Home › Vehicle Interior › SEAT › REAR NO. 1 SEAT ASSEMBLY › 2014.04–2015.08
RM19Y0E _58 Vehicle Interior _003011 SEAT _0015215 REAR NO. 1 SEAT ASSEMBLY A

SEAT  REAR NO. 1 SEAT ASSEMBLY  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp surfaces on the rear seat back frame sub-assembly and rear seat cushion spring assembly could cause injuries to your hands.


HINT:

The procedure described below is for the RH side. Use the same procedure for both the RH and LH sides, unless otherwise specified.


PROCEDURE

Hide 71621A 1.INSTALL REAR SEAT CUSHION SILENCER PAD

B292447

a.

Install the rear seat cushion silencer pad to the rear seat cushion pad.


Hide 71611A 2.INSTALL REAR SEAT CUSHION PAD

B366790

a.

Install the rear seat cushion pad to the rear seat cushion spring assembly.


Hide 71075D 3.INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER

a.
B363923C01
0.448,2.802 0.563,2.906 false 1.813,4.385 1.979,4.208 false 0.292,2.667 0.604,2.865 0.313,0.198 10 false *1 1.656,4.375 1.969,4.573 0.313,0.198 10 false *2
*1 Hog Ring
*2 Hog Ring Pliers


Using hog ring pliers, install the separate type rear seat cushion cover to the rear seat cushion pad with 14 new hog rings.

NOTICE:
·

Do not soil or scratch the separate type rear seat cushion cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seat cushion cover.




b.
B363924C01
0.427,2.792 0.583,2.917 false 1.771,4.365 1.938,4.198 false 0.281,2.646 0.594,2.844 0.313,0.198 10 false *1 1.594,4.344 1.906,4.542 0.313,0.198 10 false *2
*1 Hog Ring
*2 Hog Ring Pliers


Using hog ring pliers, install the rear seat cushion spring assembly with 9 new hog rings.

NOTICE:
·

Do not soil or scratch the separate type rear seat cushion cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seat cushion cover.




c.
B363917

Close the fastener.


Hide 72695A 4.INSTALL REAR SEAT LOCK CONTROL CABLE (for Slide Seat Type)

B296100C02
1.49,1.083 1.458,2.125 1.458,2.125 1.031,1.094 true 1.396,2.135 1.802,2.521 0.406,0.385 10 *1
*1 Band


a.

Engage the clamp.


b.

Install the rear seat lock control cable with 2 new bands.


Hide 72695A 5.INSTALL REAR SEAT LOCK CONTROL CABLE (for Non-slide Seat Type)

B292442C03
2.188,1.573 1.854,1.323 true 1.656,1.219 2.073,1.625 0.417,0.406 10 false *1
*1 Band


a.

Engage the 2 clamps.


b.

Install the rear seat lock control cable with a new band.


Hide 72695A 6.INSTALL REAR SEAT LOCK CONTROL CABLE (w/ Rear Seat Cushion Cover)

B373134C02
0.792,2.927 1.333,1.25 true 0.802,2.917 1.302,1.917 false 2.354,3.094 1.885,1.656 true 0.26,2.51 0.521,1.927 true 0.708,2.958 1.021,3.156 0.313,0.198 10 false *1 2.281,3.115 2.594,3.313 0.313,0.198 10 false *1 0.188,2.542 0.5,2.74 0.313,0.198 10 false *2
*1 Band
*2 Marking


a.

Engage the clamp.


b.

Install the rear seat lock control cable with 3 new bands.

NOTICE:

The marking on the rear seat lock control cable must face the outer side of the seat.



Hide 7.INSTALL REAR NO. 1 SEAT CUSHION OUTER LEG (for Non-slide Seat Type)

a.
B296878C01
0.677,0.5 1.26,0.708 true 0.99,0.177 1.563,0.573 true 0.688,1.177 1.229,0.792 true 0.49,0.417 0.885,0.802 0.396,0.385 10 *1 0.51,1.125 0.906,1.5 0.396,0.375 10 *2 0.802,0.073 1.167,0.375 0.365,0.302 10 *3
*1 E-Ring
*2 Pin
*3 Rear No. 1 Seat Turn Spring


Install the rear No. 1 seat turn spring and rear No. 1 seat cushion outer leg with the E-ring and pin.


Hide 8.INSTALL REAR NO. 1 SEAT CUSHION INNER LEG (for Non-slide Seat Type)

HINT:

Use the same procedures as for the rear No. 1 seat cushion outer leg.


Hide 72160C 9.INSTALL REAR NO. 1 SEAT OUTER TRACK ASSEMBLY (for Slide Seat Type)

a.
B292441

Install the rear No. 1 seat outer track assembly with the 2 bolts.

Torque:
31 N*m (316 kgf*cm, 23 ft.*lbf)


Hide 72170C 10.INSTALL REAR NO. 1 SEAT INNER TRACK ASSEMBLY (for Slide Seat Type)

HINT:

Use the same procedures as for the rear No. 1 seat outer track assembly.


Hide 72160C 11.INSTALL REAR NO. 1 SEAT OUTER TRACK ASSEMBLY (w/ Rear Seat Cushion Cover)

a.
B377990

Connect the hook of the seat track equalizing wire sub-assembly to the rear No. 1 seat outer track assembly, and then slide the coil spring in the direction of the arrow to secure it.


b.
B377951

Install the rear No. 1 seat outer track assembly with the 2 bolts.

Torque:
31 N*m (316 kgf*cm, 23 ft.*lbf)


Hide 72170C 12.INSTALL REAR NO. 1 SEAT INNER TRACK ASSEMBLY (w/ Rear Seat Cushion Cover)

HINT:

Use the same procedures as for the rear No. 1 seat outer track assembly.


Hide 71308E 13.INSTALL REAR SEAT LEG SUB-ASSEMBLY (for Slide Seat Type)

B296097

a.

Install the rear seat leg sub-assembly with the 3 nuts.

Torque:
31 N*m (316 kgf*cm, 23 ft.*lbf)


Hide 71308E 14.INSTALL REAR SEAT LEG SUB-ASSEMBLY (w/ Rear Seat Cushion Cover)

B377708

a.

Install the rear seat leg sub-assembly with the 6 nuts.

Torque:
31 N*m (316 kgf*cm, 23 ft.*lbf)


Hide 72670B 15.INSTALL REAR SEAT CUSHION LOCK ASSEMBLY (for Slide Seat Type)

a.
B296096C03
0.385,1.448 1.021,1.573 true 0.198,1.354 0.594,1.74 0.396,0.385 10 *1
*1 Rear Seat Lock Control Cable


Install the rear seat cushion lock assembly with the 2 bolts.

Torque:
31 N*m (316 kgf*cm, 23 ft.*lbf)


b.

Engage the clamp and connect the rear seat lock control cable.


Hide 72670B 16.INSTALL REAR SEAT CUSHION LOCK ASSEMBLY (for Non-slide Seat Type)

a.
B292439C01
0.552,1.271 1.24,1.75 true 0.375,1.156 0.792,1.573 0.417,0.417 10 *1
*1 Rear Seat Lock Control Cable


Install the rear seat cushion lock assembly with the 2 bolts.

Torque:
31 N*m (316 kgf*cm, 23 ft.*lbf)


b.

Engage the clamp and connect the rear seat lock control cable.


Hide 72670B 17.INSTALL REAR SEAT CUSHION LOCK ASSEMBLY (w/ Rear Seat Cushion Cover)

a.
B296096C03
0.385,1.448 1.021,1.573 true 0.198,1.354 0.594,1.74 0.396,0.385 10 *1
*1 Rear Seat Lock Control Cable


Install the rear seat cushion lock assembly with the 2 bolts.

Torque:
31 N*m (316 kgf*cm, 23 ft.*lbf)


b.

Engage the clamp and connect the rear seat lock control cable.


Hide 72670B 18.INSTALL REAR SEAT OUTER CUSHION LOCK ASSEMBLY (w/ Rear Seat Cushion Cover)

a.
B364836C01
2.771,1.042 2.125,1.646 true 2.823,0.927 3.063,1.125 0.24,0.198 10 false *1
*1 Rear Seat Lock Control Cable


Install the rear seat outer cushion lock assembly with the 2 bolts.

Torque:
31 N*m (316 kgf*cm, 23 ft.*lbf)


b.

Engage the clamp and connect the rear seat lock control cable.


Hide 73330C 19.INSTALL REAR SEAT LAP TYPE BELT ASSEMBLY

Hide 72665C 20.INSTALL REAR SEAT LOCK COVER (for Slide Seat Type)

B296094

a.

Install the rear seat lock cover with the 2 screws.


Hide 72694 21.INSTALL REAR SEAT LOCK COVER (for Non-slide Seat Type)

B296880

a.

Install the rear seat lock cover with the 2 screws.


Hide 72995 22.INSTALL REAR SEAT CUSHION COVER (w/ Rear Seat Cushion Cover)

B364870

a.

Install the rear seat cushion cover with the 4 screws.


Hide 79959 23.INSTALL REAR SEAT LEG COVER (for Slide Seat Type)

B296093

a.

Install the rear seat cushion and rear seat leg cover with the screw.


Hide 71324A 24.INSTALL REAR SEAT CUSHION (for Non-slide Seat Type)

a.
B296879

Install the rear seat cushion with the screw.


Hide 72159A 25.INSTALL REAR SEAT TRACK BRACKET COVER (for Slide Seat Type)

B364149

a.

Engage the 2 claws to install the rear seat track bracket cover.

HINT:

Use the same procedure for the other rear seat track bracket covers.



Hide 71671A 26.INSTALL REAR SEAT BACK SILENCER PAD A

B292433

a.

Install the rear seat back silencer pad A to the separate type rear seat back pad.


Hide 71651S 27.INSTALL SEPARATE TYPE REAR SEAT BACK PAD

B292432

a.

Install the separate type rear seat back pad to the rear seat back frame sub-assembly.


Hide 71077S 28.INSTALL SEPARATE TYPE REAR SEAT BACK COVER

a.
B364733C01
1.729,4.438 1.865,4.177 false 0.406,2.74 0.531,2.927 false 0.25,2.625 0.563,2.823 0.313,0.198 10 false *1 1.583,4.438 1.896,4.635 0.313,0.198 10 false *2
*1 Hog Ring
*2 Hog Ring Pliers


Using hog ring pliers, install the separate type rear seat back cover to the separate type rear seat back pad with 13 new hog rings.

NOTICE:
·

Do not soil or scratch the separate type rear seat back cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seat back cover.




b.
B364062C02
2.521,1.708 2.833,1.667 true 2.875,1.573 3.188,1.771 0.313,0.198 10 false *1
*1 Hook


Attach the hook and close the fastener.


Hide 71956B 29.INSTALL REAR SEAT HEADREST SUPPORT

a.
B296112C06
1.792,0.75 1.813,1.167 1.813,1.167 1.573,0.75 true 1.76,1.198 2.146,1.531 0.385,0.333 10 *1
*1 Protruding Portion


Align the protruding portions of the rear seat headrest support with the installation grooves of the rear seat back frame sub-assembly.


b.

Attach the 2 claws to install the rear seat headrest support.


Hide 71956B 30.INSTALL REAR SEAT HEADREST SUPPORT ASSEMBLY

a.
B296109C06
1.802,0.823 2.573,1.188 true 1.635,0.729 2.083,1.135 0.448,0.406 10 *1
*1 Protruding Portion


Align the protruding portion of the rear seat headrest support assembly with the installation groove of the rear seat back frame sub-assembly.


b.

Attach the 2 claws to install the rear seat headrest support assembly.


Hide 71940A 31.INSTALL REAR SEAT HEADREST ASSEMBLY

a.
B363920C01
3.031,1.073 3.156,1.406 true 3.115,1.448 3.427,1.646 0.313,0.198 10 false *1
*1 Lock Button


Push in the lock button of the rear seat headrest support assembly and install the rear seat headrest assembly.


Hide 32.INSTALL REAR NO. 1 SEAT BACK ASSEMBLY

a.
B292427C03
2.021,2.292 2.698,2.063 true 2.344,0.938 2.458,1.229 true 1.823,2.188 2.219,2.5 0.396,0.313 10 *1 2.448,1.26 2.802,1.604 0.354,0.344 10 *2
*1 E-Ring
*2 Bushing


Install the bushing.


b.

Install the rear No. 1 seat back assembly with the 2 bolts and E-ring.

Torque:
31 N*m (316 kgf*cm, 23 ft.*lbf)


Hide 71878A 33.INSTALL REAR SEAT INNER RECLINING COVER

a.
B292426

Engage the claw to install the rear seat inner reclining cover.


Hide 79011 34.INSTALL NO. 1 SEAT CUSHION COVER SUB-ASSEMBLY

a.
B292424

Engage the 4 claws to install the No. 1 seat cushion cover sub-assembly.


b.

Install the 2 screws.


Hide 71833D 35.INSTALL REAR SEAT RECLINING COVER

a.
B292425

Engage the 2 claws to install the rear seat reclining cover.


b.

Install the screw.


Hide 72637A 36.INSTALL REAR SEAT LOCK HANDLE

a.
B292435C02
0.698,1.5 1.344,1.385 true 0.51,1.438 0.99,1.792 0.479,0.354 10 *1
*1 Snap Ring


Install the rear seat lock handle with a new snap ring.