Home › Steering › STEERING COLUMN › STEERING WHEEL › from 2015.08
RM19Y0E _55 Steering _002998 STEERING COLUMN _0015164 STEERING WHEEL G

STEERING COLUMN  STEERING WHEEL  INSPECTION  


PROCEDURE

Hide 45100 1.INSPECT STEERING WHEEL SUB-ASSEMBLY (STEERING PAD SWITCH)

a.

Measure the resistance according to the value(s) in the table below.

C334488C01
2.313,3.323 2.646,3.323 true 1.917,3.167 1.906,2.833 1.906,2.833 2.083,2.833 true 1.333,3.5 1.667,3.5 true 2.146,3.615 2.229,3.781 true 1.833,3.833 1.833,4.167 true 4.521,2.719 4.771,2.635 true 3.583,1.333 3.885,1.333 true 4.094,0.708 4.177,0.708 4.177,0.708 4.177,1.271 true 4.573,0.76 4.323,0.76 4.323,0.76 4.323,1.26 true 4.5,1.333 4.802,1.333 true 3.708,0.938 4.042,0.938 4.042,0.938 4.042,1.271 true 2.125,2.76 2.438,2.917 0.313,0.156 10 false *1 1.167,3.417 1.479,3.573 0.313,0.156 10 false *2 2.698,3.25 3.01,3.406 0.313,0.156 10 false *3 2.219,3.823 2.531,3.979 0.313,0.156 10 false *4 1.771,4.198 2.083,4.354 0.313,0.156 10 false *5 4.823,2.552 5.135,2.708 0.313,0.156 10 false *6 3.156,0.781 3.469,0.938 0.313,0.156 10 false *a 3.354,1.25 3.646,1.469 0.292,0.219 10 false HO 3.792,0.625 4.167,0.844 0.375,0.219 10 false AU2 4.625,0.667 4.948,0.917 0.323,0.25 10 true AU1 4.854,1.26 5.229,1.479 0.375,0.219 10 false EAU 3.406,0.854 3.865,1.104 0.458,0.25 10 false IL+2
*1 Volume+ Switch *2 Volume- Switch
*3 Seek+ Switch *4 Seek- Switch
*5 MODE Switch *6 Terminal B
*a Component without harness connector
(Steering Wheel Sub-assembly (Steering Pad Switch Assembly))
- -


Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 (HO) - Terminal B Always Below 2.5 Ω
4 (AU1) - 5 (EAU) Volume+ Switch pushed 95 to 105 kΩ
Volume- Switch pushed 3105 to 3115 Ω
Seek+ Switch pushed Below 2.5 Ω
Seek- Switch pushed 324 to 334 Ω
3 (AU2) - 5 (EAU) MODE Switch pushed Below 2.5 Ω


If the result is not as specified, replace the steering wheel sub-assembly.


b.

Check the illumination.

i.

Connect the battery positive (+) lead to terminal 2 (IL+2) and the negative (-) lead to terminal 5 (EAU) of the steering pad switch assembly connector.


ii.

Check that the switch illumination comes on.

OK:

Steering pad switch illumination comes on.


If the result is not as specified, replace the steering wheel sub-assembly.