Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2015.08
RM19Y0E _57 Power Source / Network _003004 NETWORKING _0015181 CAN COMMUNICATION SYSTEM U

NETWORKING  CAN COMMUNICATION SYSTEM  TERMINALS OF ECU  


NOTICE:
·

Turn the ignition switch off before measuring the resistances between CAN main bus lines and between CAN branch lines.

·

Turn the ignition switch off before inspecting CAN bus lines for a short to ground.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

This section describes the standard values for all CAN related components.



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



NO. 1 CAN JUNCTION CONNECTOR


a.

Check the No. 1 CAN junction connector.

i.

Connection diagram

C243564C08
1.917,1.25 2.333,1.5 0.417,0.25 2.771,1.563 2.417,1.917 2.417,1.917 2.25,1.917 true 2.958,1.563 2.667,2.167 2.667,2.167 2.5,2.167 true 3.24,1.563 2.917,2.417 2.917,2.417 2.75,2.417 true 3.427,1.552 3.75,2.417 3.75,2.417 3.917,2.417 true 3.875,1.563 4.25,2.25 4.25,2.25 4.417,2.25 true 4.031,1.563 4.667,2 4.667,2 4.833,2 true 2.771,1.25 2.417,0.917 2.417,0.917 2.25,0.917 true 2.948,1.24 2.667,0.5 2.667,0.5 2.5,0.5 true 3.24,1.229 2.917,0.167 2.917,0.167 2.75,0.167 true 3.417,1.25 3.75,0.167 3.75,0.167 3.917,0.167 true 3.865,1.25 4.25,0.417 4.25,0.417 4.417,0.417 true 4.042,1.25 4.667,0.833 4.667,0.833 4.833,0.833 true 2.031,1.823 2.271,2.042 0.24,0.219 10 false *b 2.281,2.073 2.49,2.323 0.208,0.25 10 false *c 2.552,2.333 2.844,2.583 0.292,0.25 10 false *d 4.885,1.906 5.167,2.135 0.281,0.229 10 false *g 4.469,2.167 4.76,2.427 0.292,0.26 10 false *f 3.969,2.333 4.25,2.552 0.281,0.219 10 false *e 0.115,0.094 0.771,0.708 0.656,0.615 10 false *a 2,1.292 2.365,1.542 0.365,0.25 10 false E87 2.042,0.823 2.281,1.042 0.24,0.219 10 false *b 2.302,0.396 2.51,0.646 0.208,0.25 10 false *c 2.552,0.094 2.844,0.344 0.292,0.25 10 false *d 3.969,0.094 4.25,0.313 0.281,0.219 10 false *e 4.49,0.344 4.781,0.604 0.292,0.26 10 false *f 4.875,0.74 5.156,0.969 0.281,0.229 10 false *g
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to Airbag ECU Assembly
(for V bus)
*c to Power Steering ECU Assembly
(for V bus)
*d to DLC3
(for V bus)
*e to Combination Switch ECU (Switch Base)
(for V bus)
*f to Main Body ECU (Fuse Block Assembly)
(for V bus)
*g to Combination Meter Assembly
(for V bus)
- -



ii.

Check the connection diagram of the components which are connected to the No. 1 CAN junction connector.

Terminal No. Wiring Color Connected to
E87-1 Y Airbag ECU assembly
(for V bus)
E87-12 GR
E87-2 SB Power steering ECU assembly
(for V bus)
E87-13 BR
E87-4 G-W DLC3
(for V bus)
E87-15 L-W
E87-5 G Combination switch ECU (switch base)
(for V bus)
E87-16 B
E87-8 BE Main body ECU (fuse block assembly)
(for V bus)
E87-19 W
E87-9 W Combination meter assembly
(for V bus)
E87-20 P




DLC3


a.

Disconnect the cable from the negative (-) battery terminal.


b.
E231257C39
1.458,0.26 1.865,0.51 0.406,0.25 1.031,0.406 1.198,0.406 1.198,0.406 1.531,0.906 true 2.5,0.417 2.333,0.417 2.333,0.417 2,0.917 true 2.667,1.833 2.5,1.833 2.5,1.833 2.344,1.469 true 1.583,1.833 1.75,1.833 1.75,1.833 1.917,1.469 true 0.104,0.094 0.5,0.417 0.396,0.323 10 false *1 2.583,0.344 3.167,0.667 0.583,0.323 10 false CANH 0.854,0.323 1.188,0.656 0.333,0.333 10 false E 2.74,1.75 3.083,2 0.344,0.25 10 false BAT 1.156,1.76 1.573,2.01 0.417,0.25 10 false CANL 1.542,0.302 2.042,0.635 0.5,0.333 10 false E12
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
V Bus Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
E12-6 (CANH) - E12-14 (CANL) G-W - L-W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
E12-6 (CANH) - E12-4 (E) G-W - BR-W HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
E12-14 (CANL) - E12-4 (E) L-W - BR-W LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
E12-6 (CANH) - E12-16 (BAT) G-W - B-R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E12-14 (CANL) - E12-16 (BAT) L-W - B-R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




ECM


A348484C02
2.021,0.583 2.438,0.833 0.417,0.25 4.333,0.583 4.75,0.833 0.417,0.25 2.792,1.438 2.792,0.344 2.792,0.344 2.625,0.344 true 2.896,1.438 2.885,0.344 2.885,0.344 3.052,0.344 true 2.896,1.656 2.896,2.49 2.896,2.49 3.063,2.49 true 2.792,1.667 2.792,2.5 2.792,2.5 2.625,2.5 true 0.083,0.094 0.479,0.458 0.396,0.365 10 false *a 2.115,0.625 2.51,0.99 0.396,0.365 10 false A24 4.417,0.625 4.813,0.99 0.396,0.365 10 false C50 2.188,2.417 2.677,2.698 0.49,0.281 10 false CANH 3.125,2.417 3.615,2.698 0.49,0.281 10 false CANL 3.125,0.271 3.615,0.552 0.49,0.281 10 false LCAN 2.177,0.26 2.667,0.542 0.49,0.281 10 false HCAN
*a Component without harness connected
(ECM)
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.
C329971C04
1.521,2.76 1.938,3.01 0.417,0.25 1.5,0.427 1.917,0.677 0.417,0.25 2.552,3.24 2.667,2.802 2.667,2.802 2.833,2.802 true 2.573,0.927 2.74,0.427 2.74,0.427 2.906,0.427 true 0.948,1.104 0.948,0.188 0.948,0.188 1.115,0.188 true 0.833,1.115 0.833,0.438 0.833,0.438 0.667,0.438 true 0.948,1.427 0.948,2.302 0.948,2.302 1.115,2.302 true 0.833,1.427 0.833,2.313 0.833,2.313 0.667,2.313 true 0.115,0.115 0.427,0.417 0.313,0.302 10 false *a 1.594,0.469 2.031,0.771 0.438,0.302 10 false A24 1.604,2.813 2.042,3.115 0.438,0.302 10 false C50 1.167,2.24 1.677,2.552 0.51,0.313 10 false CANH 0.281,2.25 0.792,2.563 0.51,0.313 10 false CANL 0.26,0.375 0.771,0.688 0.51,0.313 10 false LCAN 1.167,0.125 1.677,0.438 0.51,0.313 10 false HCAN 2.948,0.354 3.365,0.604 0.417,0.25 10 false +B1 2.875,2.74 3.24,2.969 0.365,0.229 10 false E01
*a Front view of wire harness connector
(to ECM)


Disconnect the A24 and C50 ECM connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
V Bus Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A24-25 (HCAN) - A24-26 (LCAN) GR - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A24-25 (HCAN) - C50-4 (E01) GR - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A24-26 (LCAN) - C50-4 (E01) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A24-25 (HCAN) - A24-1 (+B1) GR - G HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A24-26 (LCAN) - A24-1 (+B1) W - G LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

V Bus Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A24-39 (CANH) - A24-40 (CANL) R - G HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 200 Ω or higher
A24-39 (CANH) - C50-4 (E01) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A24-40 (CANL) - C50-4 (E01) G - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A24-39 (CANH) - A24-1 (+B1) R - G HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A24-40 (CANL) - A24-1 (+B1) G - G LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




COMBINATION METER ASSEMBLY


E177004C03
3.396,0.313 3.813,0.563 0.417,0.25 3.979,1.104 4.354,0.417 4.354,0.417 4.521,0.417 true 3.76,1.104 3,0.417 3,0.417 2.833,0.417 true 2.385,0.354 2.969,0.698 0.583,0.344 10 false CANH 4.583,0.354 5.146,0.635 0.563,0.281 10 false CANL 3.49,0.365 3.958,0.594 0.469,0.229 10 false E34 0.115,0.094 0.448,0.375 0.333,0.281 10 false *a
*a Component without harness connected
(Combination Meter Assembly)
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.
E208723C03
1.49,0.271 1.906,0.521 0.417,0.25 0.781,1.104 0.5,0.667 0.5,0.667 0.333,0.667 true 1.24,1.115 0.667,0.417 0.667,0.417 0.5,0.417 true 1.396,1.104 1.083,0.167 1.083,0.167 0.917,0.167 true 1.552,1.104 2.25,0.417 2.25,0.417 2.417,0.417 true 0.115,0.104 0.448,0.396 0.333,0.292 10 false *a 1.573,0.313 1.906,0.604 0.333,0.292 10 false E34 0.094,0.583 0.427,0.875 0.333,0.292 10 false +B 0.323,0.344 0.656,0.635 0.333,0.292 10 false E 2.479,0.344 2.979,0.635 0.5,0.292 10 false CANH 0.531,0.094 1.031,0.385 0.5,0.292 10 false CANL
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the E34 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
V Bus Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
E34-9 (CANH) - E34-8 (CANL) W - P HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
E34-9 (CANH) - E34-7 (E) W - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
E34-8 (CANL) - E34-7 (E) P - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
E34-9 (CANH) - E34-3 (+B) W - P HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E34-8 (CANL) - E34-3 (+B) P - P LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)


C330018C04
3.302,0.229 3.719,0.479 0.417,0.25 2.917,1.063 2.5,0.333 2.5,0.333 2.333,0.333 true 2.917,1.385 2.583,2.333 2.583,2.333 2.417,2.333 true 0.125,0.115 0.458,0.438 0.333,0.323 10 false *a 3.385,0.271 3.802,0.594 0.417,0.323 10 false A13 1.948,2.26 2.531,2.594 0.583,0.333 10 false CANH 1.927,0.25 2.51,0.583 0.583,0.333 10 false CANL
*a Component without harness connected
(Skid Control ECU (Brake Actuator Assembly))
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.
C330019C15
1.51,0.25 1.927,0.5 0.417,0.25 2.333,0.333 2.167,0.333 2.167,0.333 2.021,0.99 true 1.5,1.917 1.667,1.917 1.667,1.917 2.01,1.229 true 0.583,1.927 0.75,1.927 0.75,1.927 0.896,1.354 true 2.75,1.917 2.583,1.917 2.583,1.917 2.5,1.375 true 0.115,0.094 0.427,0.344 0.313,0.25 10 false *a 1.583,0.292 1.979,0.583 0.396,0.292 10 false A13 1.073,1.844 1.604,2.094 0.531,0.25 10 false CANH 2.365,0.26 2.875,0.563 0.51,0.302 10 false CANL 2.823,1.844 3.25,2.083 0.427,0.24 10 false +BS 0.146,1.854 0.667,2.094 0.521,0.24 10 false GND1
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Disconnect the A13 skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
V Bus Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A13-22 (CANH) - A13-10 (CANL) R - G HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
A13-22 (CANH) - A13-25 (GND1) R - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A13-10 (CANL) - A13-25 (GND1) G - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A13-22 (CANH) - A13-38 (+BS) R - P HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A13-10 (CANL) - A13-38 (+BS) G - P LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




MAIN BODY ECU (FUSE BLOCK ASSEMBLY)


E317948C01
0.781,4.688 1.198,4.938 0.417,0.25 1.896,4.688 2.313,4.938 0.417,0.25 1.323,5.698 1.74,5.948 0.417,0.25 0.594,6.823 1.01,7.073 0.417,0.25 2.031,6.813 2.448,7.063 0.417,0.25 1.344,7.75 1.76,8 0.417,0.25 5.885,6.813 6.302,7.063 0.417,0.25 4.26,4.698 4.677,4.948 0.417,0.25 5.844,4.677 6.26,4.927 0.417,0.25 5.854,5.688 6.271,5.938 0.417,0.25 4.219,5.698 4.635,5.948 0.417,0.25 4.25,6.813 4.667,7.063 0.417,0.25 1.417,6.417 2.083,5.833 2.083,5.833 2.25,5.833 true 1.385,6.333 0.917,5.833 0.917,5.833 0.75,5.833 true 6.115,7.521 6.365,7.854 6.365,7.854 6.531,7.854 true 6,7.521 5.75,7.854 5.75,7.854 5.583,7.854 true 1.781,2.885 2.167,3.177 0.385,0.292 10 false 3B 2.115,2.906 2.51,3.208 0.396,0.302 10 false 3C 1.708,3.219 2.115,3.5 0.406,0.281 10 false 3D 4.781,2.01 5.25,2.333 0.469,0.323 10 false 3E 4.792,2.625 5.167,2.917 0.375,0.292 10 false 3F 4.771,3.25 5.25,3.583 0.479,0.333 10 false 3G 1.344,3.479 1.74,3.781 0.396,0.302 10 false 3K 1.365,2.99 1.76,3.292 0.396,0.302 10 false 3L 4.521,3.802 4.917,4.104 0.396,0.302 10 false 3H 5.083,3.802 5.479,4.104 0.396,0.302 10 false 3I 5.604,3.792 6.083,4.167 0.479,0.375 10 false 3J 1.729,2.563 2.083,2.833 0.354,0.271 10 false 3A 0.906,4.729 1.333,5 0.427,0.271 10 false 3A 2.01,4.729 2.396,5.021 0.385,0.292 10 false 3B 1.448,5.74 1.917,6.083 0.469,0.344 10 false 3C 0.719,6.865 1.125,7.146 0.406,0.281 10 false 3D 5.979,5.74 6.417,6.083 0.438,0.344 10 false 3E 4.385,6.865 4.802,7.188 0.417,0.323 10 false 3F 6.01,6.865 6.427,7.188 0.417,0.323 10 false 3G 4.385,4.75 4.781,5.052 0.396,0.302 10 false 3H 6,4.729 6.396,5.031 0.396,0.302 10 false 3I 4.365,5.74 4.76,6.042 0.396,0.302 10 false 3J 1.469,7.802 1.865,8.104 0.396,0.302 10 false 3K 2.167,6.865 2.563,7.167 0.396,0.302 10 false 3L 5.167,7.781 5.635,8.042 0.469,0.26 10 false CANH 2.323,5.76 2.792,6.021 0.469,0.26 10 false CANL 6.573,7.771 7.042,8.031 0.469,0.26 10 false CANL 0.313,5.76 0.781,6.021 0.469,0.26 10 false CANH 0.115,0.104 0.594,0.438 0.479,0.333 10 false *a
*a Component without harness connected
(Main Body ECU (Fuse Block Assembly))
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.
C329970C02
1.51,2.667 1.927,2.917 0.417,0.25 1.438,0.469 1.854,0.719 0.417,0.25 2.052,1.281 2.406,0.542 2.406,0.542 2.573,0.542 true 2.042,1.51 2.323,2.052 2.323,2.052 2.49,2.052 true 1.865,3.823 2.094,4.396 2.094,4.396 2.26,4.396 true 1.719,3.823 1.469,4.375 1.469,4.375 1.302,4.375 true 1.073,3.552 0.74,3.135 0.74,3.135 0.573,3.135 true 0.604,1.125 0.677,0.479 0.677,0.479 0.844,0.479 true 0.125,0.135 0.458,0.406 0.333,0.271 10 false *a 1.625,2.719 2.042,3 0.417,0.281 10 false 3G 1.563,0.521 1.979,0.802 0.417,0.281 10 false 3C 2.313,4.313 2.885,4.583 0.573,0.271 10 false CANH 2.635,0.479 3.146,0.792 0.51,0.313 10 false CANH 2.552,1.979 3.063,2.292 0.51,0.313 10 false CANL 0.906,4.302 1.542,4.563 0.635,0.26 10 false CANL 0.292,3.063 0.802,3.375 0.51,0.313 10 false E11 0.896,0.417 1.406,0.729 0.51,0.313 10 false MIRB
*a Front view of wire harness connector
(to Main Body ECU (Fuse Block Assembly))


Disconnect the 3C and 3G main body ECU (fuse block assembly) connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
V Bus Main Lines (to ECM)
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
3C-21 (CANH) - 3C-30 (CANL) GR - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
3C-21 (CANH) - 3G-1 (E11) GR - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
3C-30 (CANL) - 3G-1 (E11) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
3C-21 (CANH) - 3C-1 (MIRB) GR - GR HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
3C-30 (CANL) - 3C-1 (MIRB) W - GR LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

V Bus Main Lines (to No. 1 CAN junction connector)
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
3G-17 (CANH) - 3G-16 (CANL) BE - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
3G-17 (CANH) - 3G-1 (E11) BE - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
3G-16 (CANL) - 3G-1 (E11) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
3G-17 (CANH) - 3C-1 (MIRB) BE - GR HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
3G-16 (CANL) - 3C-1 (MIRB) W - GR LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




AIRBAG ECU ASSEMBLY


C329958C02
3.563,0.385 3.979,0.635 0.417,0.25 2.438,0.385 2.854,0.635 0.417,0.25 3.188,1.76 2,0.417 2,0.417 1.833,0.417 true 3.344,1.75 4.583,0.417 4.583,0.417 4.75,0.417 true 1.385,0.344 2.042,0.594 0.656,0.25 10 false CANH 4.813,0.354 5.469,0.604 0.656,0.25 10 false CANL 0.094,0.104 0.417,0.438 0.323,0.333 10 false *a 3.656,0.438 4.042,0.729 0.385,0.292 10 false E76 2.542,0.438 2.927,0.729 0.385,0.292 10 false J18
*a Component without harness connected
(Airbag ECU Assembly)
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.
C329972C02
1.51,2.635 1.927,2.885 0.417,0.25 1.552,0.604 1.969,0.854 0.417,0.25 2.365,3.833 2.531,4.25 2.531,4.25 2.698,4.25 true 0.917,1.667 0.75,2.167 0.75,2.167 0.583,2.167 true 2.448,1.667 2.417,2.167 2.417,2.167 2.25,2.167 true 2.635,1.667 2.667,2.167 2.667,2.167 2.833,2.167 true 0.146,2.51 0.49,2.792 0.344,0.281 10 false *1 0.135,0.146 0.479,0.427 0.344,0.281 10 false *a 2.75,4.156 3.167,4.438 0.417,0.281 10 false BAT 2.885,2.094 3.385,2.375 0.5,0.281 10 false CANH 1.823,2.083 2.323,2.365 0.5,0.281 10 false CANL 0.333,2.083 0.833,2.365 0.5,0.281 10 false E1 1.604,2.677 2.021,2.969 0.417,0.292 10 false E12 1.646,0.646 2.063,0.938 0.417,0.292 10 false E76
*1 DLC3
*a Front view of wire harness connector
(to Airbag ECU Assembly)


Disconnect the E76 airbag ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
V Bus Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
E76-26 (CANH) - E76-25 (CANL) Y - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
E76-26 (CANH) - E76-16 (E1) Y - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
E76-25 (CANL) - E76-16 (E1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
E76-26 (CANH) - E12-16 (BAT) Y - B-R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E76-25 (CANL) - E12-16 (BAT) W - B-R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




POWER STEERING ECU ASSEMBLY


C329956C03
2.042,0.323 2.458,0.573 0.417,0.25 2.542,0.323 2.958,0.573 0.417,0.25 3.292,0.323 3.708,0.573 0.417,0.25 4.281,0.333 4.698,0.583 0.417,0.25 2.458,1.51 2.729,2.531 2.729,2.531 2.896,2.531 true 2.417,1.406 2,2.521 2,2.521 1.833,2.521 true 0.104,0.094 0.542,0.406 0.438,0.313 10 false *a 4.375,0.396 4.802,0.719 0.427,0.323 10 false E74 2.135,0.375 2.563,0.698 0.427,0.323 10 false E75 2.677,0.365 3.104,0.688 0.427,0.323 10 false z6 3.427,0.385 3.854,0.708 0.427,0.323 10 false z1 1.438,2.448 1.938,2.688 0.5,0.24 10 false CANL 2.979,2.448 3.479,2.688 0.5,0.24 10 false CANH
*a Component without harness connected
(Power Steering ECU Assembly)
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.
C332397C03
1.49,2.771 1.906,3.021 0.417,0.25 1.479,0.5 1.896,0.75 0.417,0.25 1.417,3.75 1.167,4.25 1.167,4.25 1,4.25 true 2,3.75 2.25,4.25 2.25,4.25 2.417,4.25 true 1.417,1.698 1,2.115 1,2.115 0.833,2.115 true 1.417,1.375 1,0.958 1,0.958 0.833,0.958 true 0.094,0.094 0.469,0.448 0.375,0.354 10 false *a 1.573,2.813 1.99,3.104 0.417,0.292 10 false E74 1.563,0.542 1.979,0.833 0.417,0.292 10 false E75 0.583,4.167 1.083,4.458 0.5,0.292 10 false BAT+ 2.479,4.167 2.979,4.458 0.5,0.292 10 false GND 0.396,2.042 0.896,2.333 0.5,0.292 10 false CANH 0.417,0.875 0.917,1.167 0.5,0.292 10 false CANL
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


Disconnect the E74 and E75 power steering ECU assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
V Bus Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
E75-5 (CANH) - E75-1 (CANL) SB - BR HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
E75-5 (CANH) - E74-2 (GND) SB - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
E75-1 (CANL) - E74-2 (GND) BR - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
E75-5 (CANH) - E74-1 (BAT+) SB - B HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E75-1 (CANL) - E74-1 (BAT+) BR - B LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




COMBINATION SWITCH ECU (SWITCH BASE)


C329954C02
4.021,0.219 4.438,0.469 0.417,0.25 4.396,1.667 4.646,2.417 4.646,2.417 4.813,2.417 true 4.177,1.667 3.906,2.417 3.906,2.417 3.74,2.417 true 0.104,0.104 0.469,0.479 0.365,0.375 10 false *a 3.302,2.344 3.854,2.656 0.552,0.313 10 false CANH 4.885,2.344 5.438,2.656 0.552,0.313 10 false CANL 4.104,0.26 4.573,0.573 0.469,0.313 10 false E68
*a Component without harness connected
(Combination Switch ECU (Switch Base))
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.
C329955C05
1.479,0.271 1.896,0.521 0.417,0.25 1.76,1.563 2,1.927 2,1.927 2.167,1.927 true 1.521,1.573 1.281,1.938 1.281,1.938 1.115,1.938 true 1.354,1.448 0.917,1 0.917,1 0.75,1 true 1.938,1.448 2.5,0.917 2.5,0.917 2.667,0.917 true 0.104,0.104 0.427,0.396 0.323,0.292 10 false *a 1.563,0.313 1.938,0.563 0.375,0.25 10 false E68 2.229,1.844 2.969,2.042 0.74,0.198 10 false CANH 0.677,1.854 1.052,2.104 0.375,0.25 10 false CANL 0.302,0.917 0.76,1.208 0.458,0.292 10 false GND2 2.729,0.833 3.188,1.125 0.458,0.292 10 false +B
*a Front view of wire harness connector
(to Combination Switch ECU (Switch Base))


Disconnect the E68 combination switch ECU (switch base) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
V Bus Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
E68-8 (CANH) - E68-7 (CANL) G - B HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
E68-8 (CANH) - E68-6 (GND2) G - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
E68-7 (CANL) - E68-6 (GND2) B - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
E68-8 (CANH) - E68-9 (+B) G - P HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E68-7 (CANL) - E68-9 (+B) B - P LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher