Home › Vehicle Interior › SEAT › REAR NO. 1 SEAT ASSEMBLY › from 2015.08
RM19Y0E _58 Vehicle Interior _003011 SEAT _0015215 REAR NO. 1 SEAT ASSEMBLY A

SEAT  REAR NO. 1 SEAT ASSEMBLY  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp surfaces on the rear seatback frame sub-assembly and rear seat cushion spring assembly could cause injuries to your hands.


HINT:

The procedure described below is for the RH side. Use the same procedure for both the RH and LH sides, unless otherwise specified.


PROCEDURE

Hide 71621A 1.INSTALL REAR SEAT CUSHION SILENCER PAD

a.

Install the rear seat cushion silencer pad to the rear seat cushion pad.


Hide 71611A 2.INSTALL REAR SEAT CUSHION PAD

a.

Install the rear seat cushion pad to the rear seat cushion spring assembly.


Hide 71075D 3.INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER

a.
B363923C01
0.448,2.802 0.563,2.906 false 1.813,4.385 1.979,4.208 false 0.292,2.667 0.604,2.865 0.313,0.198 10 false *1 1.656,4.375 1.969,4.573 0.313,0.198 10 false *2
*1 Hog Ring
*2 Hog Ring Pliers


Using hog ring pliers, install the separate type rear seat cushion cover to the rear seat cushion pad with 14 new hog rings.

NOTICE:
·

Be careful not to damage the separate type rear seat cushion cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seat cushion cover.




b.
B363924C01
0.427,2.792 0.583,2.917 false 1.771,4.365 1.938,4.198 false 0.281,2.646 0.594,2.844 0.313,0.198 10 false *1 1.594,4.344 1.906,4.542 0.313,0.198 10 false *2
*1 Hog Ring
*2 Hog Ring Pliers


Using hog ring pliers, install the rear seat cushion spring assembly with 9 new hog rings.

NOTICE:
·

Be careful not to damage the separate type rear seat cushion cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seat cushion cover.




Hide 72695A 4.INSTALL REAR SEAT LOCK CONTROL CABLE

B411999C02
2.146,2.125 1.031,3.052 1.031,3.052 1.677,1.74 true 2.208,1.417 1.969,0.448 true 3.01,1.438 2.323,3 true 0.948,3.104 1.26,3.26 0.313,0.156 10 false *1 2.229,3.052 2.542,3.208 0.313,0.156 10 false *2 1.865,0.25 2.177,0.406 0.313,0.156 10 false *1
*1 Band
*2 Marking


a.

Engage the clamp.


b.

Install the rear seat lock control cable with 3 new bands.

NOTICE:

The marking on the rear seat lock control cable must face the outer side of the seat.



c.
B411998C01
2.25,1.885 3.063,1.219 3.063,1.219 2.323,0.271 true 3.135,1.156 3.354,1.354 0.219,0.198 10 false *1
*1 Fastener


Close the fastener.


Hide 72160C 5.INSTALL REAR NO. 1 SEAT OUTER TRACK ASSEMBLY

a.
B412002

Connect the hook of the seat track equalizing wire sub-assembly to the rear No. 1 seat outer track assembly, and then slide the coil spring in the direction of the arrow to secure it.


b.
B412003

Install the rear No. 1 seat outer track assembly with the 2 bolts.

Torque:
31 N*m (316 kgf*cm, 23 ft.*lbf)


Hide 72170C 6.INSTALL REAR NO. 1 SEAT INNER TRACK ASSEMBLY

HINT:

Use the same procedures as for the rear No. 1 seat outer track assembly.


Hide 71308E 7.INSTALL REAR SEAT LEG SUB-ASSEMBLY

a.

Install the rear seat leg sub-assembly with the 6 nuts.

Torque:
31 N*m (316 kgf*cm, 23 ft.*lbf)


Hide 72670B 8.INSTALL REAR SEAT CUSHION LOCK ASSEMBLY

a.

Install the rear seat cushion lock assembly with the 2 bolts.

Torque:
17.5 N*m (178 kgf*cm, 13 ft.*lbf)


b.

Engage the clamp and connect the rear seat lock control cable.


Hide 72670B 9.INSTALL REAR SEAT OUTER CUSHION LOCK ASSEMBLY

a.

Install the rear seat outer cushion lock assembly with the 2 bolts.

Torque:
17.5 N*m (178 kgf*cm, 13 ft.*lbf)


b.

Engage the clamp and connect the rear seat lock control cable.


Hide 73330C 10.INSTALL REAR SEAT LAP TYPE CENTER BELT ASSEMBLY

Hide 72995 11.INSTALL REAR SEAT CUSHION COVER

a.

Install the rear seat cushion cover with the 4 screws.


Hide 72159A 12.INSTALL REAR SEAT TRACK BRACKET COVER

a.

Engage the 2 claws to install the rear seat track bracket cover.

HINT:

Use the same procedure for the other rear seat track bracket covers.



Hide 71671A 13.INSTALL REAR SEATBACK SILENCER PAD A

a.

Install the rear seatback silencer pad A to the separate type rear seatback pad.


Hide 71651S 14.INSTALL SEPARATE TYPE REAR SEATBACK PAD

a.

Install the separate type rear seatback pad to the rear seatback frame sub-assembly.


Hide 71077S 15.INSTALL SEPARATE TYPE REAR SEATBACK COVER

a.
B412004C01
0.573,2.906 0.448,2.729 true 1.688,4.396 1.844,4.177 true 0.271,2.615 0.583,2.813 0.313,0.198 10 false *1 1.625,4.427 1.802,4.615 0.177,0.188 10 false *2
*1 Hog Ring
*2 Hog Ring Pliers


Using hog ring pliers, install the separate type rear seatback cover to the separate type rear seatback pad with 13 new hog rings.

NOTICE:
·

Be careful not to damage the separate type rear seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover.




b.
B411989C01
1.229,0.823 0.875,0.208 0.875,0.208 2.458,0.594 true 0.677,0.115 0.99,0.271 0.313,0.156 10 false *1
*1 Fastener


Attach the hook and close the fastener.


Hide 71956B 16.INSTALL REAR SEAT HEADREST SUPPORT

a.
B296112C06
1.792,0.75 1.813,1.167 1.813,1.167 1.573,0.75 true 1.76,1.198 2.146,1.531 0.385,0.333 10 *1
*1 Protruding Portion


Align the protruding portions of the rear seat headrest support with the installation grooves of the rear seatback frame sub-assembly.


b.

Attach the 2 claws to install the rear seat headrest support.

HINT:

Use the same procedure as for all rear seat headrest supports.



Hide 71956B 17.INSTALL REAR SEAT HEADREST SUPPORT ASSEMBLY

a.
B296109C06
1.802,0.823 2.573,1.188 true 1.635,0.729 2.083,1.135 0.448,0.406 10 *1
*1 Protruding Portion


Align the protruding portion of the rear seat headrest support assembly with the installation groove of the rear seatback frame sub-assembly.


b.

Attach the 2 claws to install the rear seat headrest support assembly.

HINT:

Use the same procedure as for all rear seat headrest support assemblies.



Hide 71878A 18.INSTALL REAR SEAT INNER RECLINING COVER

a.

Engage the 2 claws to install the rear seat inner reclining cover.


Hide 19.INSTALL REAR NO. 1 SEATBACK ASSEMBLY

a.
B411987C02
2.573,2 2.313,1.729 true 2.604,1.99 2.802,2.156 0.198,0.167 10 false *1
*1 Rear Seat Lock Control Cable


Install the rear No. 1 seatback assembly with the 4 bolts.

Torque:
31 N*m (316 kgf*cm, 23 ft.*lbf)


b.

Engage the clamp to connect the rear seat lock control cable.


Hide 79011 20.INSTALL NO. 1 SEAT CUSHION COVER SUB-ASSEMBLY

a.

Engage the 4 claws to install the No. 1 seat cushion cover sub-assembly.


b.

Install the 2 screws.


Hide 71833D 21.INSTALL REAR SEAT RECLINING COVER

a.

Engage the 2 claws to install the rear seat reclining cover.


b.

Install the screw.


Hide 72637A 22.INSTALL REAR SEAT LOCK HANDLE

a.
B292435C02
0.698,1.5 1.344,1.385 true 0.51,1.438 0.99,1.792 0.479,0.354 10 *1
*1 Snap Ring


Install the rear seat lock handle with a new snap ring.