Home › Vehicle Interior › SEAT › REAR NO. 2 SEAT ASSEMBLY › from 2015.08
RM19Y0E _58 Vehicle Interior _003011 SEAT _0015216 REAR NO. 2 SEAT ASSEMBLY A

SEAT  REAR NO. 2 SEAT ASSEMBLY  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp surfaces on the No. 2 seatback frame sub-assembly and No. 2 seat cushion spring assembly could cause injuries to your hands.


HINT:

The procedure described below is for the RH side. Use the same procedure for both the RH and LH sides, unless otherwise specified.


PROCEDURE

Hide 71622A 1.INSTALL REAR SEAT CUSHION SILENCER PAD B

a.

Install the rear seat cushion silencer pad B to the No. 2 seat cushion pad sub-assembly.


Hide 79035A 2.INSTALL NO. 2 SEAT CUSHION PAD SUB-ASSEMBLY

a.

Install the No. 2 seat cushion pad sub-assembly to the No. 2 seat cushion spring assembly.


Hide 79165 3.INSTALL REAR NO. 2 SEAT LEG BRACKET RH

NOTICE:
B412669C01
0.479,1.281 0.896,1.052 false 1.938,1.438 2.448,1.229 false 0.313,1.219 0.625,1.417 0.313,0.198 10 false *1 1.5,1.854 1.813,2.052 0.313,0.198 10 false *b 0.125,0.49 0.438,0.688 0.313,0.198 10 false *a 1.74,1.354 2.052,1.552 0.313,0.198 10 false *2
*1 Rear No. 2 Seat Leg Bracket RH
*2 Rear No. 2 Seat Leg Bracket LH
*a Right Side of Vehicle
*b Front of Vehicle


Do not confuse the rear No. 2 seat leg bracket RH with the rear No. 2 seat leg bracket LH.


a.
B412027C02
0.313,0.979 0.49,0.74 false 2.583,1.75 2.802,1.49 false 1.021,0.76 2.438,0.458 2.438,0.458 2.281,1.167 false 0.198,1.01 0.51,1.208 0.313,0.198 10 false *1 2.458,0.302 2.771,0.5 0.313,0.198 10 false *2 2.49,1.781 2.802,1.979 0.313,0.198 10 false *3
*1 Spring Nut
*2 Bushing
*3 Pin


Install the rear No. 2 seat leg bracket RH with the spring nut, 2 bushings and pin.


Hide 79166 4.INSTALL REAR NO. 2 SEAT LEG BRACKET LH

NOTICE:
B412669C01
0.479,1.281 0.896,1.052 false 1.938,1.438 2.448,1.229 false 0.313,1.219 0.625,1.417 0.313,0.198 10 false *1 1.5,1.854 1.813,2.052 0.313,0.198 10 false *b 0.125,0.49 0.438,0.688 0.313,0.198 10 false *a 1.74,1.354 2.052,1.552 0.313,0.198 10 false *2
*1 Rear No. 2 Seat Leg Bracket RH
*2 Rear No. 2 Seat Leg Bracket LH
*a Right Side of Vehicle
*b Front of Vehicle


Do not confuse the rear No. 2 seat leg bracket RH with the rear No. 2 seat leg bracket LH.


a.
B412676C02
0.344,0.958 0.625,0.604 false 1.344,0.708 2.792,0.344 2.792,0.344 2.625,1.135 false 2.927,1.708 3.104,1.469 false 2.823,1.76 3.135,1.958 0.313,0.198 10 false *1 2.854,0.208 3.167,0.406 0.313,0.198 10 false *2 0.271,1.01 0.583,1.208 0.313,0.198 10 false *3
*1 Spring Nut
*2 Bushing
*3 Pin


Install the rear No. 2 seat leg bracket LH with the spring nut, 2 bushings and pin.


Hide 79021A 5.INSTALL NO. 2 SEAT CUSHION COVER SUB-ASSEMBLY

B412663C01
0.542,2.927 0.448,2.75 false 1.604,4.385 1.719,4.156 false 0.271,2.646 0.583,2.844 0.313,0.198 10 false *1 1.49,4.427 1.802,4.625 0.313,0.198 10 false *2
*1 Hog Ring
*2 Hog Ring Pliers


a.

Using hog ring pliers, install the No. 2 seat cushion cover sub-assembly to the No. 2 seat cushion pad sub-assembly with 3 new hog rings.

NOTICE:
·

Be careful not to damage the separate type rear seat cushion cover sub-assembly.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the No. 2 seat cushion cover sub-assembly.




b.
B412664C01
0.521,2.927 0.396,2.698 false 1.667,4.396 1.823,4.177 false 1.531,4.417 1.844,4.615 0.313,0.198 10 false *2 0.24,2.615 0.552,2.813 0.313,0.198 10 false *1
*1 Hog Ring
*2 Hog Ring Pliers


Using hog ring pliers, install 7 new hog rings.

NOTICE:
·

Be careful not to damage the separate type rear seat cushion cover sub-assembly.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the No. 2 seat cushion cover sub-assembly.




Hide 79107D 6.INSTALL REAR NO. 2 SEAT LEG SUB-ASSEMBLY

a.
B412026C02
0.26,0.906 0.271,0.521 false 3.052,1.719 3.063,1.333 false 1.479,0.542 2.031,0.219 2.031,0.219 1.885,0.552 false 0.219,0.938 0.531,1.135 0.313,0.198 10 false *1 2.99,1.76 3.302,1.958 0.313,0.198 10 false *1 2.042,0.073 2.354,0.271 0.313,0.198 10 false *2
*1 E-Ring
*2 Pin


Install the rear No. 2 seat leg sub-assembly with the 2 E-rings and 2 pins.


b.

Install the tension spring.


Hide 72680B 7.INSTALL REAR NO. 2 SEAT CUSHION LOCK ASSEMBLY

a.

Install the rear No. 2 seat cushion lock assembly with the 2 bolts.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 73350 8.INSTALL REAR NO. 2 SEAT INNER BELT ASSEMBLY

Hide 79952 9.INSTALL NO. 2 SEAT CUSHION COVER

a.

Engage the 2 claws to install the No. 2 seat cushion cover.


b.

Install the No. 2 seat cushion cover with the 2 screws.


Hide 72658B 10.INSTALL REAR SEAT LOCK HANDLE KNOB

a.

Engage the claw to install the rear seat lock handle knob.


Hide 79246 11.INSTALL NO. 2 SEAT LEG COVER

a.

Install the No. 2 seat leg cover with the screw.


Hide 12.INSTALL NO. 2 SEAT CUSHION

a.

Install the No. 2 seat cushion with the screw.


Hide 71393 13.INSTALL REAR SEAT CUSHION BAND

a.

Install the rear seat cushion band with the screw.


b.

Pass the rear seat cushion band through the separate type rear seat cushion cover.


c.
B412016C01
0.396,1.833 0.885,1.531 true 0.208,1.771 0.521,1.969 0.313,0.198 10 false *1
*1 Fastener


Close the fastener.


Hide 71672 14.INSTALL REAR SEATBACK SILENCER PAD B

a.

Install the rear seatback silencer pad B to the No. 2 seatback pad sub-assembly.


Hide 79037A 15.INSTALL NO. 2 SEATBACK PAD SUB-ASSEMBLY

a.

Install the No. 2 seatback pad sub-assembly to the No. 2 seatback frame sub-assembly.


Hide 79023 16.INSTALL NO. 2 SEATBACK COVER SUB-ASSEMBLY

a.
B292478C02
0.438,2.854 0.563,2.917 true 1.875,4.177 1.75,4.354 true 0.25,2.76 0.677,3.146 0.427,0.385 10 *1 1.615,4.344 2.01,4.656 0.396,0.313 10 *2
*1 Hog Ring
*2 Hog Ring Pliers


Using hog ring pliers, install the No. 2 seatback cover sub-assembly to the No. 2 seatback pad sub-assembly with 3 new hog rings.

NOTICE:
·

Be careful not to damage the No. 2 seatback cover sub-assembly.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the No. 2 seatback cover sub-assembly.




b.
B292458C01
2.177,1.99 1.792,1.76 true 2.25,1.927 2.594,2.146 0.344,0.219 10 false *1
*1 Hook


Engage the hook and close the fastener.


Hide 71931C 17.INSTALL REAR NO. 2 SEAT HEADREST SUPPORT

a.
B296112C07
1.792,0.74 1.813,1.156 1.813,1.156 1.573,0.74 true 1.76,1.177 2.188,1.573 0.427,0.396 10 *1
*1 Protruding Portion


Align the protruding portions of the rear No. 2 seat headrest support with the installation grooves of the No. 2 seatback frame sub-assembly.


b.

Engage the 2 claws to install the rear No. 2 seat headrest support.

HINT:

Use the same procedure for both sides.



Hide 71931C 18.INSTALL REAR NO. 2 SEAT HEADREST SUPPORT ASSEMBLY

a.
B296109C07
1.813,0.813 2.583,1.177 true 1.635,0.729 2.115,1.094 0.479,0.365 10 *1
*1 Protruding Portion


Align the protruding portion of the rear No. 2 seat headrest support assembly with the installation groove of the No. 2 seatback frame sub-assembly.


b.

Engage the 2 claws and install the rear No. 2 seat headrest support assembly.

HINT:

Use the same procedure for the both sides.



Hide 19.INSTALL REAR NO. 2 SEATBACK ASSEMBLY

a.
B412014C02
2.365,2.042 2.854,1.729 false 2.896,1.625 3.208,1.823 0.313,0.198 10 false *1
*1 Bushing


Install the bushing and rear No. 2 seatback assembly.


Hide 71485 20.INSTALL REAR SEAT HINGE COVER

a.
B412013

Install the rear seat hinge cover with the screw.


b.
B412012C01
1.833,1.292 2.594,1.708 true 2.656,1.635 2.969,1.833 0.313,0.198 10 false *1
*1 Hook and Loop Fastener


Fasten the hook and loop the fastener.


Hide 71303B 21.INSTALL REAR NO. 2 SEAT HINGE SUB-ASSEMBLY

a.
B292456C04
2.26,0.313 2.531,0.365 true 2.063,0.24 2.427,0.583 0.365,0.344 10 *1 1.188,0.063 1.604,0.396 0.417,0.333 10 A 0.75,1.531 1.135,1.885 0.385,0.354 10 B 1.635,1.875 1.979,2.167 0.344,0.292 10 B
*1 Bushing


Install the rear No. 2 seat hinge sub-assembly with the 3 bolts and bushing.

Torque:
Bolt A : 24 N*m (245 kgf*cm, 18 ft.*lbf)
Bolt B : 31 N*m (316 kgf*cm, 23 ft.*lbf)


Hide 79273 22.INSTALL NO. 2 SEAT HINGE COVER

a.

Install the No. 2 seat hinge cover with the 2 screws.