Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT ASSEMBLY(for Dual Beam Headlight) › from 2015.08
RM19Y0E _59 Vehicle Exterior _003020 LIGHTING (EXT) _0195741 HEADLIGHT ASSEMBLY(for Dual Beam Headlight) N

LIGHTING (EXT)  HEADLIGHT ASSEMBLY(for Dual Beam Headlight)  ADJUSTMENT  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. VEHICLE PREPARATION FOR HEADLIGHT AIMING ADJUSTMENT

a.

Prepare the vehicle:

·

Ensure that there is no damage or deformation of the body around the headlights.

·

Fill the fuel tank.

·

Fill the oil to the specified level.

·

Fill the coolant to the specified level.

·

Inflate the tires to the appropriate pressure.

·

Place the spare tire, tools and jack in their original positions.

·

Unload the trunk.

·

Sit a person of average weight (75 kg, 165 lb) in the driver seat.



Hide 2. PREPARATION FOR HEADLIGHT AIMING (Using a screen)

a.
E257168C01
1.021,1.135 1.479,1.531 0.458,0.396 10 *a 1.208,1.833 1.552,2.156 0.344,0.323 10 *b
*a 90°
*b 10 m (32.8 ft.) or 3 m (9.84 ft.)


Prepare the vehicle:

·

Place the vehicle in a location that is dark enough to clearly observe the cutoff line. The cutoff line is a distinct line, below which light from the headlights can be observed and above which it cannot.

·

Place the vehicle at a 90° angle to the wall.

·

Create a 10 m (32.8 ft.) distance between the vehicle (headlight bulb center) and wall.

·

Make sure that the vehicle is on a level surface.

·

Bounce the vehicle up and down to settle the suspension.


NOTICE:

A distance of 10 m (32.8 ft.) between the vehicle (headlight bulb center) and wall is necessary for proper aim adjustment. If unavailable, secure a distance of exactly 3 m (9.84 ft.) for the check and adjustment (the target zone will change with the distance, so follow the instructions in the illustration).



b.

Prepare a piece of thick white paper approximately 2 m (6.56 ft.) (height) x 4 m (13.1 ft.) (width) to use as a screen.


c.

Draw a vertical line down the center of the screen (V line).


d.

Set the screen as shown in the illustration.

E257169C01
1.448,0.396 1.844,0.76 0.396,0.365 10 *a 1.458,1.313 1.896,1.708 0.438,0.396 10 *b 2.656,0.823 3.042,1.188 0.385,0.365 10 *c 0.51,2.813 0.938,3.188 0.427,0.375 10 *d 1.417,3.438 1.823,3.771 0.406,0.333 10 *e 5,3.458 5.438,3.802 0.438,0.344 10 *f 1.146,0.656 1.625,1.031 0.479,0.375 10 *g 1.594,0.042 2.052,0.458 0.458,0.417 10 *A 5.229,0.083 5.604,0.385 0.375,0.302 10 *B 1.125,2.979 1.604,3.354 0.479,0.375 10 *g 4.021,2.823 4.448,3.198 0.427,0.375 10 *d 4.646,3 5.125,3.375 0.479,0.375 10 *g 4.958,0.375 5.354,0.74 0.396,0.365 10 *a 4.667,0.646 5.146,1.021 0.479,0.375 10 *g 4.958,1.271 5.396,1.667 0.438,0.396 10 *b 6.167,0.833 6.552,1.198 0.385,0.365 10 *c
*A Aligning distance is 10 m (32.8 ft.) *B Aligning distance is 3 m (9.84 ft.)
*a V RH Line *b V LH line
*c V Line *d H Line
*e 10 m (32.8 ft.) *f 3 m (9.84 ft.)
*g 90° - -


HINT:
·

Stand the screen perpendicular to the ground.

·

Align the V line on the screen with the center of the vehicle.




e.
I033423C02
0.365,1.698 0.792,2.073 0.427,0.375 10 *e 2.792,0.875 3.188,1.271 0.396,0.396 10 *d 1.604,0.333 2.021,0.698 0.417,0.365 10 *b 1,0.333 1.385,0.698 0.385,0.365 10 *a 2.26,0.313 2.646,0.708 0.385,0.396 10 *c
*a V LH Line
*b V Line
*c V RH Line
*d H Line
*e Ground


Draw base lines (H, V LH, and V RH Lines) on the screen as shown in the illustration.

HINT:
·

The base lines differ for "low beam inspection" and "high beam inspection".

·

Mark the headlight bulb center marks on the screen. If the center mark cannot be observed on the headlight, use the center of the headlight bulb or the name of the manufacturer marked on the headlight as the center mark.



i.

H Line (Headlight):

Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the headlight bulb center marks of the low beam headlights.


ii.

V LH Line, V RH Line (Center mark position of the left-hand (LH) and right-hand (RH) headlights):

Draw two vertical lines so that they intersect the H line at each center mark (aligned with the center of the low beam headlight bulbs).



Hide 3.INSPECT HEADLIGHT AIMING

a.
E257168C03
1.042,1.156 1.479,1.521 0.438,0.365 10 *a 1.281,1.854 1.604,2.146 0.323,0.292 10 *b
*a 90°
*b 10 m (32.8 ft.) or 3 m (9.84 ft.)


Cover the headlight or disconnect the connector of the headlight on the opposite side to prevent light from the headlight that is not being inspected from affecting the headlight aiming.

NOTICE:

Do not keep the headlight covered for more than 3 minutes. The headlight lens is made of synthetic resin, which may melt or be damaged due to excessive heat.


HINT:

When checking the aim of the high beam, cover the low beam or disconnect the connector.



b.

Start the engine.

NOTICE:

Engine speed must be 1500 rpm or more.



c.

Turn on the headlight and check if the cutoff line matches the preferred cutoff line in the following illustration.

E231824C06
5.896,1.688 6.188,2.177 true 2.74,1.688 3.031,2.177 true 5.094,0.854 5.5,1.167 0.406,0.313 10 false *a 1.927,0.854 2.385,1.229 0.458,0.375 10 false *a 0.875,1.302 1.427,1.677 0.552,0.375 10 false *c 3.052,2.125 3.479,2.49 0.427,0.365 10 false *d 6.219,2.135 6.656,2.51 0.438,0.375 10 false *d 4.031,1.292 4.469,1.688 0.438,0.396 10 false *c 2.281,0.865 2.729,1.24 0.448,0.375 10 false *b 5.448,0.854 5.969,1.229 0.521,0.375 10 false *b 0.875,0.167 1.458,0.615 0.583,0.448 12 false *A 4.052,0.167 4.563,0.615 0.51,0.448 12 false *B 1.177,1.521 1.969,1.917 0.792,0.396 10 false 150 mm 4.375,1.531 5.073,1.948 0.698,0.417 10 false 45 mm 3.323,1.479 4.135,1.875 0.813,0.396 10 false 100 mm 6.469,1.458 7.156,1.917 0.688,0.458 10 false 30 mm 1.719,2.063 2.427,2.573 0.708,0.51 10 false 99 mm 2.26,2.073 3.031,2.469 0.771,0.396 10 false 99 mm 4.896,2.042 5.667,2.479 0.771,0.438 10 false 81 mm 5.448,2.052 6.135,2.427 0.688,0.375 10 false 81 mm 5.563,1.198 6.313,1.604 0.75,0.406 10 false 6 mm 2.385,1.198 3.104,1.552 0.719,0.354 10 false 20 mm
*A Aligning distance is 10 m (32.8 ft.) *B Aligning distance is 3 m (9.84 ft.)
*a V RH Line *b V LH line
*c H Line *d Cutoff Line


HINT:
·

Since the low beam light and the high beam light are a unit, if the aim on the low beam is correct, the high beam should also be correct. However, check both beams just to make sure.

·

If the alignment distance is 10 m (32.8 ft.):

The low beam cutoff line should be within 99 mm (3.91 in.) and 150 mm (5.91 in.) below the H line as well as 99 mm (3.91 in.) left or right of the V LH or V RH line.

·

If the alignment distance is 3.0 m (9.84 ft.):

The low beam cutoff line should be within 30 mm (1.18 in.) and 45 mm (1.77 in.) below the H line as well as 30 mm (1.18 in.) left or right of the V LH or V RH line.

·

If the alignment distance is 10 m (32.8 ft.):

The horizontal line of the preferred low beam cutoff line is 100 mm (3.91 in.) below the H line and point A of the preferred low beam cutoff line is on the V LH or V RH line.

·

If the alignment distance is 3.0 m (9.84 ft.):

The horizontal line of the preferred low beam cutoff line is 30 mm (1.18 in.) below the H line and point A of the preferred low beam cutoff line is on the V LH or V RH line.




Hide 4.ADJUST HEADLIGHT AIMING

a.
E321211C01
0.896,1.948 1.302,3.073 true 2.344,0.479 3,0.385 3,0.385 3.073,1.125 false 1.635,2.563 2.094,3.073 true 1.26,3.125 1.573,3.281 0.313,0.156 10 false *1 2.094,3.125 2.406,3.281 0.313,0.156 10 false *2 3,0.177 3.313,0.333 0.313,0.156 10 false *3
*1 Horizontal Aiming Screw
*2 Vertical Aiming Screw
*3 Screwdriver


Adjust the aim of each headlight to the specified range by turning each aiming screw with a screwdriver.

NOTICE:

The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it, and then retighten it so that the final turn of the screw is in the clockwise direction.


HINT:
·

If it is not possible to correctly adjust headlight aim, check the bulb, headlight unit and headlight unit reflector installation.

·

The headlight aim moves up when turning the vertical aiming screw clockwise, and moves down when turning the vertical aiming screw counterclockwise. The headlight aim moves right when turning the horizontal aiming screw clockwise, and moves left when turning the horizontal aiming screw counterclockwise.