The standard voltage between each pair of the ECM terminals is shown in the table below. The appropriate conditions for checking each pair of the terminals are also indicated.
The result of checks should be compared with the standard voltage for that pair of terminals, and displayed in the "Specified Condition" column.
The illustration above can be used as a reference to identify the ECM terminal locations.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A24-1 (+B1) - C50-4 (E01) | G - W-B | Power source of ECM | Ignition switch ON | 11 to 14 V |
| A24-2 (+B2) - C50-5 (E02) | G - W-B | Power source of ECM | Ignition switch ON | 11 to 14 V |
| A24-6 (+BM) - C50-4 (E01) | LG - W-B | Power source of throttle actuator | Ignition switch ON | 11 to 14 V |
| A24-8 (FC2) - C50-4 (E01) | BE - W-B | Fuel pump control signal | Ignition switch ON | 11 to 14 V |
| Idling | Below 1.5 V | |||
| A24-9 (FAN) - C50-4 (E01) | LG - W-B*1
V - W-B*2 |
Cooling fan control signal | Ignition switch ON, cooling fan off | 11 to 14 V |
| Cooling fan on*1
Cooling fan on (Low)*2 |
Below 1.5 V | |||
| A24-10 (FAN2) - C50-4 (E01)*2 | L - W-B | Cooling fan control signal | Ignition switch ON, cooling fan off | 11 to 14 V |
| Cooling fan on (High) | Below 1.5 V | |||
| A24-12 (REV) - C50-4 (E01) | R - W-B | Engine speed signal | Idling with warm engine | Pulse generation
(See waveform 1) |
| A24-13 (BAT) - C50-4 (E01) | G - W-B | Battery (for measuring battery voltage and for ECM memory) | Always | 11 to 14 V |
| A24-14 (IGSW) - C50-4 (E01) | Y - W-B | Ignition switch signal | Ignition switch ON | 11 to 14 V |
| A24-16 (MGC) - C50-4 (E01) | P - W-B | Magnet clutch control signal | Ignition switch ON, magnetic clutch off | 11 to 14 V |
| Magnetic clutch on | Below 1.5 V | |||
| A24-19 (ETR) - C50-4 (E01) | GR - W-B | E-THRO relay operation signal | Ignition switch ON | Below 1.5 V |
| A24-22 (CLT) - C50-4 (E01)*3 | B - W-B | Clutch start switch signal | Ignition switch ON, clutch pedal released | Below 1.5 V |
| Ignition switch ON, clutch pedal depressed | 11 to 14 V | |||
| A24-25 (HCAN) - C50-4 (E01) | GR - W-B | CAN communication line | Ignition switch ON | Pulse generation
(See waveform 2) |
| A24-26 (LCAN) - C50-4 (E01) | W - W-B | CAN communication line | Ignition switch ON | Pulse generation
(See waveform 3) |
| A24-28 (MRO) - C50-4 (E01) | W - W-B | EFI-MAIN relay operation signal | Ignition switch ON | Below 1.5 V |
| A24-29 (VCO) - A24-57 (E24) | Y - BR | Power source of air conditioner pressure sensor | Ignition switch ON | 4.75 to 5.25 V |
| A24-30 (VCP1) - A24-58 (EPA) | L - R | Power source of accelerator pedal sensor (for VPA) | Ignition switch ON | 4.5 to 5.5 V |
| A24-31 (VCP2) - A24-59 (EPA2) | V - W | Power source of accelerator pedal sensor (for VPA2) | Ignition switch ON | 4.5 to 5.5 V |
| A24-39 (CANH) - C50-4 (E01) | R - W-B | CAN communication line | Ignition switch ON | Pulse generation
(See waveform 2) |
| A24-40 (CANL) - C50-4 (E01) | G - W-B | CAN communication line | Ignition switch ON | Pulse generation
(See waveform 3) |
| A24-43 (ACAD) - A24-57 (E24) | B - BR | Air conditioner pressure sensor signal | Ignition switch ON | 0.5 to 4.8 V |
| A24-44 (VPA) - A24-58 (EPA) | G - R | Accelerator pedal sensor signal (for engine control) | Ignition switch ON, accelerator pedal fully released | 0.5 to 1.1 V |
| Ignition switch ON, accelerator pedal fully depressed | 2.6 to 4.5 V | |||
| A24-45 (VPA2) - A24-59 (EPA2) | GR - W | Accelerator pedal sensor signal | Ignition switch ON, accelerator pedal fully released | 1.2 to 2.0 V |
| Ignition switch ON, accelerator pedal fully depressed | 3.4 to 4.75 V | |||
| A24-46 (STR-) - C50-4 (E01) | L - W-B | Starter signal | Cranking | Below 1.5 V |
| Idling | Below 1.5 V | |||
| A24-48 (STP) - C50-4 (E01) | Y - W-B | Stop light switch signal | Brake pedal released | Below 1.5 V |
| Brake pedal depressed | 11 to 14 V | |||
| A24-54 (SIO2) - C50-4 (E01)*4 | P - W-B | Immobiliser communication | Ignition switch ON | Pulse generation |
| A24-60 (STSW) - C50-4 (E01) | R - W-B | Starter signal | Cranking | 11 to 14 V |
| Idling | Below 1.5 V | |||
| A24-62 (ST1-) - C50-4 (E01) | V - W-B | Stop light switch signal (opposite of voltage at STP terminal) | Ignition switch ON, brake pedal released | 7.5 to 14 V |
| Ignition switch ON, brake pedal depressed | Below 1.5 V | |||
| A24-63 (PBSW) - C50-4 (E01)*5 | W-R - W-B | Vacuum warning switch signal | Ignition switch ON, brake pedal released | 11 to 14 V |
| Ignition switch ON, brake pedal depressed | Below 1.5 V | |||
| A24-64 (T) - C50-4 (E01) | L - W-B | Terminal EFIT of DLC3 | Ignition switch ON | 11 to 14 V |
| A24-68 (R) - C50-4 (E01)*3 | V - W-B | Back-up light switch signal | Ignition switch ON, shift lever in R | 11 to 14 V |
| Ignition switch ON, shift lever not in R | Below 1.5 V | |||
| C50-1 (M+) - C50-3 (MR01) | GR - W-B | Throttle actuator operation signal (positive terminal) | Idling with warm engine | Pulse generation
(See waveform 4) |
| C50-2 (M-) - C50-3 (MR01) | L - W-B | Throttle actuator operation signal (negative terminal) | Idling with warm engine | Pulse generation
(See waveform 5) |
| C50-3 (MR01) - Body ground | W-B - - | Ground circuit of throttle actuator | Always | Below 1 Ω |
| C50-4 (E01) - Body ground | W-B - - | Ground circuit of ECM | Always | Below 1 Ω |
| C50-5 (E02) - Body ground | W-B - - | Ground circuit of ECM | Always | Below 1 Ω |
| C50-8 (OXH1) - C50-4 (E01) | L - W-B | Oxygen sensor heater signal | Ignition switch ON | 11 to 14 V |
| Idling | Below 3.0 V | |||
| C50-10 (OCV+) - C50-11 (OCV-) | P - G | Camshaft timing oil control valve signal (for intake camshaft) | Idling with warm engine | Pulse generation
(See waveform 6) |
| C50-12 (OCV2+) - C50-13 (OCV2-) | GR - V | Camshaft timing oil control valve signal (for exhaust camshaft) | Idling with warm engine | Pulse generation
(See waveform 7) |
| C50-18 (#10) - C50-4 (E01) | R - W-B | No. 1 fuel injector signal | Ignition switch ON | 11 to 14 V |
| Idling with warm engine | Pulse generation
(See waveform 8) |
|||
| C50-19 (#20) - C50-4 (E01) | W - W-B | No. 2 fuel injector signal | Ignition switch ON | 11 to 14 V |
| Idling with warm engine | Pulse generation
(See waveform 8) |
|||
| C50-20 (#30) - C50-4 (E01) | B - W-B | No. 3 fuel injector signal | Ignition switch ON | 11 to 14 V |
| Idling with warm engine | Pulse generation
(See waveform 8) |
|||
| C50-21 (#40) - C50-4 (E01) | BR - W-B | No. 4 fuel injector signal | Ignition switch ON | 11 to 14 V |
| Idling with warm engine | Pulse generation
(See waveform 8) |
|||
| C50-30 (OX) - C50-51 (OX-) | W - B | Oxygen sensor signal | Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor | Pulse generation
(See waveform 9) |
| C50-32 (THW) - C50-100 (E2) | V-Y - BR-W | Engine coolant temperature sensor | Idling with warm engine, engine coolant temperature 80°C (176°F) | 0.2 to 1.0 V |
| C50-33 (VTHO) - C50-99 (ETA) | B - W | Throttle position sensor signal (for engine control) | Ignition switch ON, accelerator pedal fully released | 0.5 to 1.1 V |
| Ignition switch ON, accelerator pedal fully depressed | 3.2 to 4.8 V | |||
| C50-40 (IG1) - C50-4 (E01) | V-W - W-B | No. 1 ignition coil signal | Idling with warm engine | Pulse generation
(See waveform 10) |
| C50-41 (IG2) - C50-4 (E01) | BR-B - W-B | No. 2 ignition coil signal | Idling with warm engine | Pulse generation
(See waveform 10) |
| C50-42 (IG3) - C50-4 (E01) | G-R - W-B | No. 3 ignition coil signal | Idling with warm engine | Pulse generation
(See waveform 10) |
| C50-43 (IG4) - C50-4 (E01) | R-Y - W-B | No. 4 ignition coil signal | Idling with warm engine | Pulse generation
(See waveform 10) |
| C50-50 (NSSP) - C50-4 (E01)*3 | P-G - W-B | Ground circuit | Always | Below 1 Ω |
| C50-55 (VCTA) - C50-99 (ETA) | R - W | Power source of throttle position sensor (specific voltage) | Ignition switch ON | 4.5 to 5.5 V |
| C50-57 (VCN) - C50-101 (EN) | GR-L - W-L | Power source of crankshaft position sensor | Ignition switch ON | 4.5 to 5.5 V |
| C50-58 (VCG) - C50-102 (EGIN) | P-B - GR-R | Power source of camshaft position sensor (for intake camshaft) | Ignition switch ON | 4.5 to 5.5 V |
| C50-59 (VCG) - C50-103 (EGEX) | W-R - B-W | Power source of camshaft position sensor (for exhaust camshaft) | Ignition switch ON | 4.5 to 5.5 V |
| C50-74 (THA) - C50-100 (E2) | R-L - BR-W | Intake air temperature sensor | Idling, intake air temperature 0 to 80°C (32 to 176°F) | 0.5 to 3.5 V |
| C50-76 (VG) - C50-98 (E2G) | V-R - GR-G | Intake air flow meter signal | Idling, shift lever in P or N, A/C switch off | 0.5 to 3.0 V |
| C50-77 (VTA2) - C50-99 (ETA) | G - W | Throttle position sensor signal (for sensor malfunction detection) | Ignition switch ON, accelerator pedal fully released | 2.1 to 3.1 V |
| Ignition switch ON, accelerator pedal fully depressed | 4.6 to 5.0 V | |||
| C50-79 (N) - C50-101 (EN) | LG-R - W-L | Crankshaft position sensor signal | Idling with warm engine | Pulse generation
(See waveform 11) |
| C50-80 (GIN) - C50-102 (EGIN) | G-W - GR-R | Camshaft position sensor signal (for intake camshaft) | Idling with warm engine | Pulse generation
(See waveform 12) |
| C50-81 (GEX) - C50-103 (EGEX) | R-G - B-W | Camshaft position sensor signal (for exhaust camshaft) | Idling with warm engine | Pulse generation
(See waveform 12) |
| C50-84 (MOPS) - C50-4 (E01) | G-B - W-B | Engine oil pressure switch signal | Ignition switch ON | Below 1.5 V |
| Idling | 11 to 14 V | |||
| C50-87 (PRG) - C50-4 (E01) | BR-Y - W-B | No. 1 vacuum switching valve signal | Idling, under purge control | Pulse generation
(See waveform 13) |
| C50-100 (E2) - Body ground | BR-W - - | Ground circuit of ECM | Always | Below 1 Ω |
| C50-105 (E1) - Body ground | W-B - - | Ground circuit of ECM | Always | Below 1 Ω |
| C50-106 (KNK) - C50-100 (E2) | L - BR-W | Knock control sensor signal | Engine speed maintained at 4000 rpm after warming up engine | Pulse generation
(See waveform 14) |
*1: w/o Resistor
*2: w/ Resistor
*3: for Manual Transmission
*4: w/ Engine Immobiliser System
*5: for Automatic Transmission
WAVEFORM 1
| ECM Terminal Name | Between REV and E01 |
| Tester Range | 5 V/DIV., 20 msec./DIV. |
| Condition | Idling with warm engine |
The wavelength becomes shorter as the engine speed increases.
WAVEFORM 2
| ECM Terminal Name | Between HCAN and E01, or CANH and E01 |
| Tester Range | 1 V/DIV., 10 μsec./DIV. |
| Condition | Ignition switch ON |
The waveform varies depending on the CAN communication signal.
WAVEFORM 3
| ECM Terminal Name | Between LCAN and E01, or CANL and E01 |
| Tester Range | 1 V/DIV., 10 μsec./DIV. |
| Condition | Ignition switch ON |
The waveform varies depending on the CAN communication signal.
WAVEFORM 4
| ECM Terminal Name | Between M+ and MR01 |
| Tester Range | 5 V/DIV., 1 msec./DIV. |
| Condition | Idling with warm engine |
The duty ratio varies depending on the throttle actuator operation.
WAVEFORM 5
| ECM Terminal Name | Between M- and MR01 |
| Tester Range | 5 V/DIV., 1 msec./DIV. |
| Condition | Idling with warm engine |
The duty ratio varies depending on the throttle actuator operation.
WAVEFORM 6
| ECM Terminal Name | Between OCV+ and OCV- |
| Tester Range | 5 V/DIV., 1 msec./DIV. |
| Condition | Idling with warm engine |
WAVEFORM 7
| ECM Terminal Name | Between OCV2+ and OCV2- |
| Tester Range | 5 V/DIV., 1 msec./DIV. |
| Condition | Idling with warm engine |
WAVEFORM 8
| ECM Terminal Name | Between #10 (to #40) and E01 |
| Tester Range | 10 V/DIV., 2 msec./DIV. |
| Condition | Idling with warm engine |
The wavelength becomes shorter as the engine speed increases.
WAVEFORM 9
| ECM Terminal Name | Between OX and OX- |
| Tester Range | 0.2 V/DIV., 200 msec./DIV. |
| Condition | Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor |
WAVEFORM 10
| ECM Terminal Name | Between IG1 (to IG4) and E01 |
| Tester Range | 2 V/DIV., 20 msec./DIV. |
| Condition | Idling with warm engine |
The wavelength becomes shorter as the engine speed increases.
WAVEFORM 11
| ECM Terminal Name | Between N and EN |
| Tester Range | 2 V/DIV., 5 msec./DIV. |
| Condition | Idling with warm engine |
The wavelength becomes shorter as the engine speed increases.
WAVEFORM 12
| ECM Terminal Name | CH1: Between GIN and EGIN
CH2: Between GEX and EGEX |
| Tester Range | 5 V/DIV., 20 msec./DIV. |
| Condition | Idling with warm engine |
The wavelength becomes shorter as the engine speed increases.
WAVEFORM 13
| ECM Terminal Name | Between PRG and E01 |
| Tester Range | 10 V/DIV., 20 msec./DIV. |
| Condition | Idling, under purge control |
If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.
WAVEFORM 14
| ECM Terminal Name | Between KNK and E2 |
| Tester Range | 1 V/DIV., 1 msec./DIV. |
| Condition | Engine speed maintained at 4000 rpm after warming up engine |
The wavelength becomes shorter as the engine speed increases.
The waveforms and amplitudes displayed differ slightly depending on the vehicle condition.