13801
1.INSPECT NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
Turn the roller by hand to check that it turns smoothly.
If the roller does not turn smoothly, replace the No. 1 valve rocker arm sub-assembly.
13750
2.INSPECT VALVE LASH ADJUSTER ASSEMBLY
Keep the valve lash adjuster assembly free of dirt and foreign matter.
Only use clean engine oil.
Place the valve lash adjuster assembly into a container filled with engine oil.
| *a | Correct |
| *b | Incorrect |
| *c | Taper Part |
| *d | Low Pressure Chamber |
| *e | High Pressure Chamber |
| *f | Plunger |
| *g | Check Ball |
Insert the tip of SST into the valve lash adjuster assembly plunger and use the tip to press down on the check ball inside the plunger.
Squeeze SST and the valve lash adjuster assembly together to move the plunger up and down 5 to 6 times.
Check the movement of the plunger and bleed it.
Plunger moves up and down.
When bleeding the high-pressure chamber, make sure that the tip of SST is actually pressing the check ball as shown in the illustration. If the check ball is not pressed, the high-pressure chamber will not be bled.
After bleeding, remove SST. Then, try to quickly and firmly press the plunger by hand.
Plunger is very difficult to move.
If the result is not as specified, replace the valve lash adjuster assembly.
13050
3.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY
Install the camshaft timing gear assembly.
Check that the straight pin is installed on the camshaft.
| *a | Key Groove |
| *b | Straight Pin |
Fit the camshaft timing gear assembly and camshaft together by aligning the key groove and straight pin.
Do not forcefully push in the camshaft timing gear assembly. This may cause the camshaft straight pin tip to damage the installation surface of the camshaft timing gear assembly.
Do not turn the camshaft timing gear assembly in the retard direction (clockwise).
Tighten the bolt with the camshaft timing gear assembly secured in place.
Check the locked state of the camshaft timing gear assembly.
Confirm that the camshaft timing gear assembly is locked.
| *a | Open |
| *b | Close |
| *c | Advance Side Path |
| *d | Retard Side Path |
| *e | Rubber |
| *f | Vinyl Tape |
Release the lock pin.
Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.
There are 4 oil paths in the groove of the camshaft. Plug 3 of the paths with pieces of rubber.
Prick a hole in the tape placed on the retard side path, on the opposite side to that of the advance side path, as shown in the illustration.
| *a | Advance Side Path |
While applying approximately 150 kPa (1.5 kgf/cm2, 22 psi) of air pressure to the oil paths, forcibly turn the camshaft timing gear assembly in the advance direction (counterclockwise).
Cover the paths with a piece of cloth when applying pressure to keep engine oil from spraying.
Do not lock the camshaft timing gear assembly. If it is locked, release the lock pin again.
The camshaft timing gear assembly may be turned in the advance direction without applying any force.
If enough air pressure cannot be applied because of air leaks from the port, releasing the lock pin may be difficult.
Check for smooth rotation.
Turn the camshaft timing gear assembly within its movable range (26.5 to 28.5°) 2 or 3 times, but do not turn it to the most retarded position. Make sure that the camshaft timing gear assembly turns smoothly.
Do not lock the camshaft timing gear assembly. If it is locked, release the lock pin again.
13070A
4.INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
Install the camshaft timing exhaust gear assembly.
Check that the straight pin is installed on the No. 2 camshaft.
| *a | Key Groove |
| *b | Straight Pin |
Fit the camshaft timing exhaust gear assembly and No. 2 camshaft together by aligning the key groove and straight pin.
Do not forcefully push in the camshaft timing exhaust gear assembly. This may cause the camshaft straight pin tip to damage the installation surface of the camshaft timing exhaust gear assembly.
Be sure not to turn the camshaft timing exhaust gear assembly in the retard direction (clockwise).
Tighten the bolt with the camshaft timing exhaust gear assembly secured in place.
Check locked state of the camshaft timing exhaust gear assembly.
Make sure that the camshaft timing exhaust gear assembly is locked.
| *a | Open |
| *b | Close |
| *c | Advance Side Path |
| *d | Retard Side Path |
| *e | Rubber |
| *f | Vinyl Tape |
Release the lock pin.
Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.
The 4 oil paths are provided in the grooves. Plug 2 paths with rubber pieces.
Prick a hole in the tape placed on the advance side path. Prick a hole in the tape placed on the retard side path, on the opposite side to that of the advance side path, as shown in the illustration.
| *a | Advance Side Path |
| *b | Retard Side Path |
Apply approximately 200 kPa (2.0 kgf/cm2, 29 psi) of air pressure to the 2 paths (the advance side path and the retard side path).
Cover the paths with a piece of cloth when applying pressure to keep engine oil from spraying.
| *a | Hold Pressure |
| *b | Release Pressure |
| *c | Advance Side Path |
| *d | Retard Side Path |
Make sure that the camshaft timing exhaust gear assembly turns in the retard direction (clockwise) when reducing the air pressure applied to the advance side path.
The lock pin is released and the camshaft timing exhaust gear assembly turns in the retard direction.
When the camshaft timing exhaust gear assembly moves to the most retarded position, release the air pressure from the advance side path, then release the air pressure from the retard side path.
Be sure to release the air pressure from the advance side path first. If the air pressure of the retard side path is released first, the camshaft timing exhaust gear assembly may abruptly shift in the advance direction and break the lock pin or other parts.
Check for smooth rotation.
Turn the camshaft timing exhaust gear assembly within its movable range (19 to 21°) 2 or 3 times, but do not turn it to the most advanced position. Make sure that the camshaft timing exhaust gear assembly turns smoothly.
When the air pressure is released from the advance side path, then from the retard side path, the camshaft timing exhaust gear assembly automatically returns to the most advanced position due to the advance assist spring operation and locks. Gradually release the air pressure from the retard side path before performing the smooth rotation check.
Check the locked state at the most advanced position.
Make sure that the camshaft timing exhaust gear assembly is locked at the most advanced position.
13506
5.INSPECT CHAIN SUB-ASSEMBLY
| *a | Measurement Area |
Pull the chain sub-assembly with a force of 147 N (15 kgf, 33 lbf) as shown in the illustration.
Using a vernier caliper, measure the length of 15 links.
114.8 mm (4.519 in.)
Perform the measurement at 3 random places. Use the average of the measurements.
If the average elongation is greater than the maximum, replace the chain sub-assembly.
13050
6.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY
| *a | Chain Roller |
Place the chain sub-assembly around the camshaft timing gear assembly.
Using a vernier caliper, measure the diameter of the camshaft timing gear assembly and chain sub-assembly.
96.8 mm (3.811 in.)
The vernier caliper must be in contact with the chain sub-assembly rollers when measuring.
If the diameter is less than the minimum, replace the chain sub-assembly and camshaft timing gear assembly.
13070A
7.INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
| *a | Chain Roller |
Place the chain sub-assembly around the camshaft timing exhaust gear assembly.
Using a vernier caliper, measure the diameter of the camshaft timing exhaust gear assembly and chain sub-assembly.
96.8 mm (3.811 in.)
The vernier caliper must be in contact with the chain sub-assembly rollers when measuring.
If the diameter is less than the minimum, replace the chain sub-assembly and camshaft timing exhaust gear assembly.
13521
8.INSPECT CRANKSHAFT TIMING GEAR OR SPROCKET
| *a | Chain Roller |
Place the chain sub-assembly around the crankshaft timing gear or sprocket.
Using a vernier caliper, measure the diameter of the crankshaft timing gear or sprocket and chain sub-assembly.
51.1 mm (2.012 in.)
The vernier caliper must be in contact with the chain sub-assembly rollers when measuring.
If the diameter is less than the minimum, replace the chain sub-assembly and crankshaft timing gear or sprocket.
13591
9.INSPECT TIMING CHAIN TENSION ARM
Using a vernier caliper, measure the timing chain tension arm for wear.
1.0 mm (0.0394 in.)
If the wear is greater than the maximum, replace the timing chain tension arm.
13566B
10.INSPECT TIMING CHAIN GUIDE
Using a vernier caliper, measure the timing chain guide for wear.
1.0 mm (0.0394 in.)
If the wear is greater than the maximum, replace the timing chain guide.
13562
11.INSPECT NO. 2 CHAIN VIBRATION DAMPER
Using a vernier caliper, measure the No. 2 chain vibration damper for wear.
1.0 mm (0.0394 in.)
If the wear is greater than the maximum, replace the No. 2 chain vibration damper.
13540
12.INSPECT NO. 1 CHAIN TENSIONER ASSEMBLY
| *a | Raise |
| *b | Move |
| *c | Lock |
Check that the plunger moves smoothly when the ratchet pawl is raised by hand.
Release the ratchet pawl, then check that the plunger is locked in place by the ratchet pawl and does not move when pushed by hand.
13511
13.INSPECT CAMSHAFT
Inspect the camshaft for runout.
Place the camshaft on V-blocks.
Using a dial indicator, measure the runout at the center journal.
0.04 mm (0.00157 in.)
If the runout is greater than the maximum, replace the camshaft.
Inspect the cam lobes.
Using a micrometer, measure the cam lobe height.
41.749 to 41.849 mm (1.6437 to 1.6476 in.)
41.499 mm (1.6338 in.)
If the cam lobe height is less than the minimum, replace the camshaft.
Inspect the camshaft journals.
Using a micrometer, measure the journal diameter.
| Journal Position | Specified Condition |
|---|---|
| No. 1 | 34.454 to 34.470 mm (1.3565 to 1.3571 in.) |
| Other | 22.954 to 22.970 mm (0.9037 to 0.9043 in.) |
If the journal diameter is not as specified, check the camshaft oil clearance.
Click hereEngine / Hybrid System>1NR-VE ENGINE MECHANICAL>CYLINDER HEAD>INSPECTION
13512
14.INSPECT NO. 2 CAMSHAFT
Inspect the No. 2 camshaft for runout.
Place the No. 2 camshaft on V-blocks.
Using a dial indicator, measure the runout at the center journal.
0.04 mm (0.00157 in.)
If the runout is greater than the maximum, replace the No. 2 camshaft.
Inspect the cam lobes.
Using a micrometer, measure the cam lobe height.
41.0 to 41.1 mm (1.6142 to 1.6181 in.)
40.80mm (1.6063 in.)
If the cam lobe height is less than the minimum, replace the No. 2 camshaft.
Inspect the No. 2 camshaft journals.
Using a micrometer, measure the journal diameter.
| Journal Position | Specified Condition |
|---|---|
| No. 1 | 34.454 to 34.470 mm (1.3565 to 1.3571 in.) |
| Other | 22.954 to 22.970 mm (0.9037 to 0.9043 in.) |
If the journal diameter is not as specified, check the camshaft oil clearance.
Click hereEngine / Hybrid System>1NR-VE ENGINE MECHANICAL>CYLINDER HEAD>INSPECTION
11101A
15.INSPECT CYLINDER HEAD SET BOLT
| *a | Measurement Length |
Using a vernier caliper, measure the length of the cylinder head set bolt from the seat to the end.
125.3 to 126.7 mm (4.9331 to 4.9882 in.)
128.2 mm (5.047 in.)
If the length is greater than the maximum, replace the cylinder head set bolt with a new one.
25051
16.INSPECT EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
Using a straightedge and feeler gauge, check the surface cylinder head sub-assembly for warpage.
0.8 mm (0.0315 in.)
If the warpage is greater than the maximum, replace the exhaust manifold converter sub-assembly.