Home › Engine / Hybrid System › 1NR-VE ENGINE MECHANICAL › CYLINDER HEAD › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042273 1NR-VE ENGINE MECHANICAL _0196185 CYLINDER HEAD A

1NR-VE ENGINE MECHANICAL  CYLINDER HEAD  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL SPARK PLUG TUBE

a.
A204168C10
1.521,1.344 2.042,1.76 2.042,1.76 2.354,1.76 true 2.354,0.396 3.396,0.573 1.042,0.177 10 false *a 2.406,1.667 2.75,1.823 0.344,0.156 10 false *b
*a Protrusion Height
*b Mark


Using paint, mark the standard position from the edge.

Standard protrusion height:

88.7 to 90.2 mm (3.492 to 3.551 in.)



b.
A204167C16
0.438,0.719 0.5,0.177 0.5,0.177 0.833,0.177 false 0.531,0.719 0.583,0.333 0.583,0.333 0.833,0.333 false 0.521,1.458 0.833,1.833 0.833,1.833 1.125,1.833 false 1.177,1.75 1.802,1.917 0.625,0.167 10 false *a 0.885,0.281 1.24,0.5 0.354,0.219 10 false *c 0.885,0.083 1.219,0.333 0.333,0.25 10 false *b
*a Adhesive
*b 3.0 to 9.0 mm (0.118 to 0.354 in.)
*c 1.0 to 3.0 mm (0.0394 to 0.118 in.)


Apply adhesive to the spark plug tube where it will be pressed into the cylinder head.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



c.
A286219C07
0.646,0.198 0.823,0.198 0.823,0.198 1.313,0.396 false 1.646,0.271 1.875,0.156 1.875,0.156 2.104,0.156 false 1.198,2.74 1.458,2.74 1.458,2.74 1.823,3.229 true 1,2.635 1.313,2.833 0.313,0.198 10 false *a 2.302,2.594 2.615,2.792 0.313,0.198 10 false *b 2.156,0.063 2.469,0.26 0.313,0.198 10 false *d 0.479,0.125 0.792,0.323 0.313,0.198 10 false *c
*a Mark
*b Protrusion Height
*c Wooden Block
*d Press


Using a press and wooden block, install the spark plug tube to the specified protrusion height.

Standard protrusion height:

88.7 to 90.2 mm (3.492 to 3.551 in.)


NOTICE:
·

Install the spark plug tube within 3 minutes of applying adhesive.

·

Do not start the engine within 1 hour after installation.

·

Do not deform the spark plug tube.

·

Be careful not to drip the adhesive.




Hide 13734 2.INSTALL VALVE SPRING SEAT

a.

Install the valve spring seats to the cylinder head sub-assembly.


Hide 3.INSTALL VALVE STEM OIL SEAL

a.
A146313C10
2.104,0.792 2.313,0.792 2.313,0.792 2.417,1.156 false 0.979,1.125 1.125,0.823 1.125,0.823 1.323,0.823 false 0.635,0.531 1.677,0.76 1.042,0.229 10 *a 2.552,0.531 3.021,0.906 0.469,0.375 10 *b 1.375,0.729 1.729,0.906 0.354,0.177 10 *c 1.938,0.729 2.344,0.906 0.406,0.177 10 *d
*a Intake Side
*b Exhaust Side
*c Silver
*d Black


Apply a light coat of engine oil to new valve stem oil seals.

NOTICE:

Pay close attention when installing the intake and exhaust valve stem oil seals. Installing the intake oil seal to the exhaust side or installing the exhaust valve stem oil seal to the intake side may cause installation problems later.


HINT:

The intake valve stem oil seal is silver and the exhaust valve stem oil seal is black.



b.
A198028C06
2.427,0.094 2.26,0.094 2.26,0.094 1.635,0.719 true 2.49,0.031 2.917,0.271 0.427,0.24 10 false SST 0.406,2.333 0.708,2.646 0.302,0.313 10 false *a 1.635,2.323 2.031,2.594 0.396,0.271 10 false *b
*a Correct
*b Incorrect


Using SST, push in the valve stem oil seals.

SST
09201-41020  

NOTICE:

Make sure to use SST, or the valve stem oil seals may be damaged or improperly seated.



Hide 13711 4.INSTALL INTAKE VALVE

a.
A286223C02
2.635,1.573 2.948,1.771 0.313,0.198 10 *a
*a 30 mm (1.18 in.) or more


Sufficiently apply engine oil to the tip area of the intake valve shown in the illustration.


b.
A314495C01
1.229,0.677 1.479,0.677 false 1.313,1.333 1.563,1.333 false 0.927,1.667 1.188,1.854 false 1.115,1.25 1.427,1.406 0.313,0.156 10 false *1 1.042,0.615 1.354,0.771 0.313,0.156 10 false *2 0.708,1.583 1.021,1.74 0.313,0.156 10 false *3 1.677,0.146 1.99,0.302 0.313,0.156 10 false *a
*1 Inner Compression Spring
*2 Valve Spring Retainer
*3 Cylinder Head Sub-assembly
*a Upper Side


Install the intake valve, inner compression spring and valve spring retainer to the cylinder head sub-assembly.

NOTICE:
·

Install the inner compression spring with its taper side facing upward (towards the valve spring retainer)

·

Install the same parts to their original positions.




c.
A314488C04
0.677,0.438 0.958,0.573 false 1.917,3.115 2.073,2.854 true 1.792,3.177 2.104,3.333 0.313,0.156 10 false *a 0.365,0.354 0.823,0.552 0.458,0.198 10 false SST
*a Wooden Block


Using SST and wooden blocks, compress the inner compression spring and install the 2 valve spring retainer locks.

SST
09202-70020  09202-00020  


d.
A314491

Using a plastic-faced hammer, lightly tap the intake valve stem tip to ensure a proper fit.

NOTICE:
·

Be careful not to damage the intake valve stem tip.

·

Be careful not to tap the retainer.




Hide 13715 5.INSTALL EXHAUST VALVE

a.
A286224C02
2.635,1.656 2.948,1.854 0.313,0.198 10 *a
*a 30 mm (1.18 in.) or more


Sufficiently apply engine oil to the tip area of the exhaust valve shown in the illustration.


b.
A314495C01
1.229,0.677 1.479,0.677 false 1.313,1.333 1.563,1.333 false 0.927,1.667 1.188,1.854 false 1.115,1.25 1.427,1.406 0.313,0.156 10 false *1 1.042,0.615 1.354,0.771 0.313,0.156 10 false *2 0.708,1.583 1.021,1.74 0.313,0.156 10 false *3 1.677,0.146 1.99,0.302 0.313,0.156 10 false *a
*1 Inner Compression Spring
*2 Valve Spring Retainer
*3 Cylinder Head Sub-assembly
*a Upper Side


Install the exhaust valve, inner compression spring and valve spring retainer to the cylinder head sub-assembly.

NOTICE:
·

Install the inner compression spring with its taper side facing upward (towards the valve spring retainer)

·

Install the same parts to their original positions.




c.
A314489C04
2.969,2.167 3.125,1.917 true 2.083,3.052 2.24,2.802 true 1.958,0.708 2.115,0.49 false 1.979,3.115 2.292,3.271 0.313,0.156 10 false *a 2.135,0.365 2.594,0.563 0.458,0.198 10 false SST 2.823,2.188 3.135,2.344 0.313,0.156 10 false *a
*a Wooden Block


Using SST and wooden blocks, compress the inner compression spring and install the 2 valve spring retainer locks.

SST
09202-70020  09202-00020  


d.
A314492

Using a plastic-faced hammer, lightly tap the exhaust valve stem tip to ensure a proper fit.

NOTICE:
·

Be careful not to damage the exhaust valve stem tip.

·

Be careful not to tap the retainer.




Hide 13716 6.INSTALL VALVE STEM CAP

a.

Apply a light coat of engine oil to the valve stem caps.


b.

Install the valve stem caps to the cylinder head sub-assembly.