Home › Engine / Hybrid System › 1NR-VE ENGINE MECHANICAL › CYLINDER BLOCK › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042273 1NR-VE ENGINE MECHANICAL _0196186 CYLINDER BLOCK A

1NR-VE ENGINE MECHANICAL  CYLINDER BLOCK  REPLACEMENT  


PROCEDURE

Hide 1.REPLACE RING PIN

NOTICE:

It is not necessary to remove the ring pins unless they are being replaced.


a.

Remove the 2 ring pins.


b.
A198047C06
0.167,0.167 0.479,0.323 0.313,0.156 10 false *a 0.854,2.677 1.167,2.833 0.313,0.156 10 false *b 1.333,3.083 1.646,3.24 0.313,0.156 10 false *c 1.896,3.698 2.208,3.854 0.313,0.156 10 false *d
*a Upper Side
*b 13 mm (0.512 in.)
*c 12 mm (0.472 in.)
*d 6.5 to 7.5 mm (0.256 to 0.295 in.)


Using a plastic hammer, tap in the 2 ring pins.

Protrusion Height:

6.5 to 7.5 mm (0.256 to 0.295 in.)



Hide 2.REPLACE STRAIGHT PIN

NOTICE:

It is not necessary to remove the straight pins unless they are being replaced.


a.

Remove the 4 straight pins.


b.

Using a plastic hammer, tap in the 4 straight pins.

A363030C01
0.667,0.083 0.979,0.24 0.313,0.156 10 false *a 4.333,0.25 4.646,0.406 0.313,0.156 10 false *b 2,3.031 2.313,3.188 0.313,0.156 10 false *c 3.917,3.073 4.229,3.229 0.313,0.156 10 false *d 6,2.99 6.313,3.146 0.313,0.156 10 false *e 1.438,1.885 1.75,2.042 0.313,0.156 10 false *f 1.729,2.281 2.063,2.531 0.333,0.25 10 false *g 3.323,1.833 3.635,1.99 0.313,0.156 10 false *h 0.854,0.406 1.01,0.604 0.156,0.198 10 false A 2.427,1.031 2.583,1.229 0.156,0.198 10 true A 0.938,0.99 1.094,1.188 0.156,0.198 10 true C 4.51,0.531 4.667,0.729 0.156,0.198 10 true B 6.479,1.208 6.635,1.406 0.156,0.198 10 true B 2.99,1.76 3.146,1.958 0.156,0.198 10 true B 1.063,1.771 1.219,1.969 0.156,0.198 10 false A 4.906,1.792 5.063,1.99 0.156,0.198 10 true C 5.448,1.615 5.76,1.771 0.313,0.156 10 false *h 3.667,2.375 3.979,2.531 0.313,0.156 10 false *i 5.802,2.219 6.115,2.375 0.313,0.156 10 false *j
*a Front Side *b Rear Side
*c 5.5 to 6.5 mm (0.217 to 0.256 in.) *d 11.5 to 12.5 mm (0.453 to 0.492 in.)
*e 23.5 to 24.5 mm (0.925 to 0.965 in.) *f 4.0 mm (0.157 in.)
*g 12.0 mm (0.472 in.) *h 10.0 mm (0.394 in.)
*i 22.0 mm (0.866 in.) *j 36.0 mm (1.417 in.)


Protrusion Height:
Item Protrusion Height
Pin A 5.5 to 6.5 mm (0.217 to 0.256 in.)
Pin B 11.5 to 12.5 mm (0.453 to 0.492 in.)
Pin C 23.5 to 24.5 mm (0.925 to 0.965 in.)