Home › Engine / Hybrid System › 1NR-VE ENGINE MECHANICAL › CYLINDER BLOCK › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042273 1NR-VE ENGINE MECHANICAL _0196186 CYLINDER BLOCK A

1NR-VE ENGINE MECHANICAL  CYLINDER BLOCK  DISASSEMBLY  


PROCEDURE

Hide 13521A 1.REMOVE CRANKSHAFT TIMING GEAR KEY

a.

Remove the crankshaft timing gear key from the crankshaft.


Hide 2.REMOVE PISTON SUB-ASSEMBLY WITH CONNECTING ROD

a.
A198034

Using a ridge reamer, remove all the carbon from the top of the cylinder.


b.
A198035N04
1.656,0.938 2.073,0.208 2.073,0.208 2.208,0.208 false 2.271,0.135 2.625,0.323 0.354,0.188 10 false SST

Using SST, uniformly loosen the 2 connecting rod bolts.

SST
09205-16010  


c.
A198036

Using the 2 removed connecting rod bolts, remove the connecting rod cap and lower connecting rod bearing by wiggling the connecting rod cap back and forth.

HINT:

Keep the lower connecting rod bearing inserted in the connecting rod cap.



d.

Push the piston sub-assembly with connecting rod sub-assembly and upper connecting rod bearing through the top of the cylinder block sub-assembly.

NOTICE:

Do not disassemble the piston, piston pin and connecting rod. If the piston pin is removed, the piston, piston pin and connecting rod cannot be reused.


HINT:
·

Keep each connecting rod bearing, connecting rod and connecting rod cap as a set.

·

Arrange the removed parts in the correct order.




Hide 13041 3.REMOVE CONNECTING ROD BEARING

a.

Remove the connecting rod bearings from the connecting rod cap and connecting rod.

HINT:

Arrange the removed parts in the correct order.



Hide 13011 4.REMOVE PISTON RING SET

a.
A363013

Using a piston ring expander, remove the No. 1 compression ring and No. 2 compression ring.


b.

Remove the 2 side rails and expander spacer by hand.

HINT:

Arrange the removed parts in the correct order.



Hide 13411 5.REMOVE CRANKSHAFT

a.
A363014N01
2.76,0.208 2.917,0.406 0.156,0.198 10 true 2 2.26,0.208 2.417,0.406 0.156,0.198 10 true 6 1.729,0.188 1.938,0.385 0.208,0.198 10 true 10 1.219,0.219 1.375,0.417 0.156,0.198 10 true 8 0.708,0.219 0.865,0.417 0.156,0.198 10 true 4 0.729,1.583 0.885,1.781 0.156,0.198 10 true 3 1.229,1.583 1.396,1.75 0.167,0.167 10 true 7 1.76,1.573 1.917,1.771 0.156,0.198 10 true 9 2.271,1.583 2.427,1.781 0.156,0.198 10 true 5 2.771,1.583 2.927,1.781 0.156,0.198 10 true 1

Uniformly loosen and remove the 10 crankshaft bearing cap set bolts in the order shown in the illustration.


b.
A198040

Using the 2 removed crankshaft bearing cap set bolts, remove the 5 crankshaft bearing caps and 5 lower crankshaft bearings.

NOTICE:

Insert the crankshaft bearing cap set bolts into the crankshaft bearing caps in turn. Ease the crankshaft bearing cap out by gently pulling it up while wiggling it back and forth, as shown in the illustration. Be careful not to damage the contact surfaces of the crankshaft bearing cap and cylinder block sub-assembly.


HINT:
·

Keep each lower crankshaft bearing and crankshaft bearing cap as a set.

·

Arrange the crankshaft bearing caps in the correct order.




c.
A363015

Remove the crankshaft from the cylinder block sub-assembly.


Hide 11791 6.REMOVE UPPER CRANKSHAFT THRUST WASHER

a.
A198042

Remove the 2 upper crankshaft thrust washers from the cylinder block sub-assembly.


Hide 11711 7.REMOVE CRANKSHAFT BEARING

a.
A198044

Remove the 5 upper crankshaft bearings from the cylinder block sub-assembly.

HINT:

Arrange the removed parts in the correct order.



b.
A198046

Remove the 5 lower crankshaft bearings from the 5 crankshaft bearing caps.

HINT:

Arrange the removed parts in the correct order.



Hide 15708 8.REMOVE NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.
A363016

Using a 5 mm socket hexagon wrench, remove the 4 bolts and 4 No. 1 oil nozzle sub-assemblies from the cylinder block sub-assembly.


Hide 11401 9.CLEAN CYLINDER BLOCK SUB-ASSEMBLY

NOTICE:

If the cylinder is washed at high temperature, the cylinder liner will stick out beyond the cylinder block sub-assembly. Always wash the cylinder block sub-assembly at a temperature of 45°C (113°F) or less.