Home › Engine / Hybrid System › 2NR-VE ENGINE MECHANICAL › CYLINDER HEAD › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042274 2NR-VE ENGINE MECHANICAL _0196195 CYLINDER HEAD A

2NR-VE ENGINE MECHANICAL  CYLINDER HEAD  REPLACEMENT  


PROCEDURE

Hide 11122 1.REPLACE INTAKE VALVE GUIDE BUSH

a.

Heat the cylinder head sub-assembly to 80 to 100°C (176 to 212°F).


b.

Place the cylinder head sub-assembly on wooden blocks.


c.
A198021N06
1.5,1.333 0.75,0.49 0.75,0.49 1.479,0.917 true 0.365,0.417 0.688,0.594 0.323,0.177 10 false SST

Using SST and a hammer, tap out the intake valve guide bush.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)


d.
A198025

Using a caliper gauge, measure the intake valve guide bush bore diameter of the cylinder head sub-assembly.

Standard bush bore diameter:

10.285 to 10.306 mm (0.40492 to 0.40575 in.)



e.

Heat the cylinder head sub-assembly to 80 to 100°C (176 to 212°F).


f.

Place the cylinder head sub-assembly on wooden blocks.


g.
A198022N03
1.521,1.354 0.75,0.49 0.75,0.49 1.479,0.865 true 0.385,0.417 0.698,0.563 0.313,0.146 10 false SST

Using SST and a hammer, tap a new intake valve guide bush into the specified protrusion height.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

Standard protrusion height:

14.6 to 15.0 mm (0.575 to 0.591 in.)



h.
A198023

Using a sharp 5.5 mm (0.217 in.) reamer, ream the intake valve guide bush to obtain the standard oil clearance between the intake valve guide bush and intake valve stem.

Standard oil clearance:

0.025 to 0.060 mm (0.000984 to 0.00236 in.)



Hide 11126 2.REPLACE EXHAUST VALVE GUIDE BUSH

a.

Heat the cylinder head sub-assembly to 80 to 100°C (176 to 212°F).


b.

Place the cylinder head sub-assembly on wooden blocks.


c.
A198018N05
1.688,1.406 0.802,0.323 0.802,0.323 1.729,1.021 true 0.438,0.24 0.74,0.396 0.302,0.156 10 false SST

Using SST and a hammer, tap out the exhaust valve guide bush.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)


d.
A198024

Using a caliper gauge, measure the exhaust valve guide bush bore diameter of the cylinder head sub-assembly.

Standard bush bore diameter:

10.285 to 10.306 mm (0.40492 to 0.40575 in.)



e.

Heat the cylinder head sub-assembly to 80 to 100°C (176 to 212°F).


f.

Place the cylinder head sub-assembly on wooden blocks.


g.
A198019N04
1.677,1.448 0.802,0.354 0.802,0.354 1.75,1 true 0.438,0.292 0.75,0.438 0.313,0.146 10 false SST

Using SST and a hammer, tap a new exhaust valve guide bush into the specified protrusion height.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

Standard protrusion height:

14.6 to 15.0 mm (0.575 to 0.591 in.)



h.
A198020

Using a sharp 5.5 mm reamer, ream the exhaust valve guide bush to obtain the standard oil clearance between the exhaust valve guide bush and exhaust valve stem.

Standard oil clearance:

0.025 to 0.060 mm (0.000984 to 0.00236 in.)



Hide 3.REPLACE RING PIN

NOTICE:

It is not necessary to remove the ring pins unless they are being replaced.


a.

Remove the 4 ring pins.


b.

Using a plastic-faced hammer, tap in 4 new ring pins to the specified protrusion height.

Protrusion Height:

4.0 to 6.0 mm (0.157 to 0.236 in.)


A363009C01
0.167,0.167 0.479,0.323 0.313,0.156 10 false *a 4.542,0.417 4.854,0.573 0.313,0.156 10 false *b 4.938,0.833 5.25,0.99 0.313,0.156 10 false *c 5.688,0.417 6,0.573 0.313,0.156 10 false *d 1.427,0.333 1.583,0.531 0.156,0.198 10 false B 1.76,0.333 1.917,0.531 0.156,0.198 10 false B 0.75,1.583 0.906,1.781 0.156,0.198 10 false A 3.677,1.75 3.833,1.948 0.156,0.198 10 false A 4.25,0.385 4.406,0.583 0.156,0.198 10 false A 5.427,0.417 5.583,0.615 0.156,0.198 10 false B 6.104,1.906 6.417,2.063 0.313,0.156 10 false *e 6.115,0.844 6.427,1 0.313,0.156 10 false *d
*a Upper Side *b 11.0 mm (0.433 in.)
*c 9.0 mm (0.354 in.) *d 12.0 mm (0.472 in.)
*e 4.0 to 6.0 mm (0.157 to 0.236 in.) - -



Hide 4.REPLACE STUD BOLT

NOTICE:

If any of the stud bolts is deformed or the threads are damaged, replace it.


a.

Remove the 9 stud bolts.


b.

Using E6 and E8 "TORX" socket wrenches, install the 9 stud bolts.

A363010C01
0.167,0.167 0.479,0.323 0.313,0.156 10 false *a 3.917,0.177 4.229,0.333 0.313,0.156 10 false *b 0.417,1.01 0.729,1.167 0.313,0.156 10 false *c 2.969,1.917 3.281,2.073 0.313,0.156 10 false *d 2.979,2.396 3.292,2.552 0.313,0.156 10 false *e 3.531,2 3.844,2.156 0.313,0.156 10 false *f 4.552,1.573 4.906,1.833 0.354,0.26 10 false *g 4.563,2.396 4.875,2.552 0.313,0.156 10 false *h 5.104,1.979 5.417,2.135 0.313,0.156 10 false *i 6.104,1.917 6.417,2.073 0.313,0.156 10 false *j 6.104,2.458 6.417,2.615 0.313,0.156 10 false *k 6.688,2.083 7,2.24 0.313,0.156 10 false *l 1.406,0.083 1.563,0.281 0.156,0.198 10 false B 1.802,0.083 1.958,0.281 0.156,0.198 10 false B 4.26,0.167 4.417,0.365 0.156,0.198 10 false A 5.177,0.167 5.333,0.365 0.156,0.198 10 false A 6.083,0.323 6.333,0.5 0.25,0.177 10 true A 5.385,1 5.542,1.198 0.156,0.198 10 false A 4.958,1 5.115,1.198 0.156,0.198 10 false A 0.708,1.583 0.865,1.781 0.156,0.198 10 false C 0.667,1.052 0.823,1.25 0.156,0.198 10 false C 2.583,1.333 2.74,1.531 0.156,0.198 10 false A 4.177,1.167 4.333,1.365 0.156,0.198 10 false B 5.75,1.417 5.906,1.615 0.156,0.198 10 false C
*a Intake Side *b Exhaust Side
*c Front Side *d 27.0 mm (1.063 in.)
*e 13.0 mm (0.512 in.) *f 42.0 mm (1.654 in.)
*g 27.0 mm (1.063 in.) *h 13.0 mm (0.512 in.)
*i 80.0 mm (3.150 in.) *j 24.5 mm (0.965 in.)
*k 9.0 mm (0.35 in.) *l 40.5 mm (1.594 in.)


Torque:
Stud bolt (A) and (B) : 9.5 N*m (97 kgf*cm, 84 in.*lbf)
Stud bolt (C) : 5.0 N*m (51 kgf*cm, 44 in.*lbf)