1.INSTALL SPARK PLUG TUBE
| *a | Protrusion Height |
| *b | Mark |
Using paint, mark the standard position from the edge.
88.7 to 90.2 mm (3.492 to 3.551 in.)
| *a | Adhesive |
| *b | 3.0 to 9.0 mm (0.118 to 0.354 in.) |
| *c | 1.0 to 3.0 mm (0.0394 to 0.118 in.) |
Apply adhesive to the spark plug tube where it will be pressed into the cylinder head.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
| *a | Mark |
| *b | Protrusion Height |
| *c | Wooden Block |
| *d | Press |
Using a press and wooden block, install the spark plug tube to the specified protrusion height.
88.7 to 90.2 mm (3.492 to 3.551 in.)
Install the spark plug tube within 3 minutes of applying adhesive.
Do not start the engine within 1 hour after installation.
Do not deform the spark plug tube.
Be careful not to drip the adhesive.
13734
2.INSTALL VALVE SPRING SEAT
Install the valve spring seats to the cylinder head sub-assembly.
3.INSTALL VALVE STEM OIL SEAL
| *a | Intake Side |
| *b | Exhaust Side |
| *c | Silver |
| *d | Black |
Apply a light coat of engine oil to new valve stem oil seals.
Pay close attention when installing the intake and exhaust valve stem oil seals. Installing the intake oil seal to the exhaust side or installing the exhaust valve stem oil seal to the intake side may cause installation problems later.
The intake valve stem oil seal is silver and the exhaust valve stem oil seal is black.
| *a | Correct |
| *b | Incorrect |
Using SST, push in the valve stem oil seals.
Make sure to use SST, or the valve stem oil seals may be damaged or improperly seated.
13711
4.INSTALL INTAKE VALVE
| *a | 30 mm (1.18 in.) or more |
Sufficiently apply engine oil to the tip area of the intake valve shown in the illustration.
| *1 | Inner Compression Spring |
| *2 | Valve Spring Retainer |
| *3 | Cylinder Head Sub-assembly |
| *a | Upper Side |
Install the intake valve, inner compression spring and valve spring retainer to the cylinder head sub-assembly.
Install the inner compression spring with its taper side facing upward (towards the valve spring retainer)
Install the same parts to their original positions.
| *a | Wooden Block |
Using SST and wooden blocks, compress the inner compression spring and install the 2 valve spring retainer locks.
Using a plastic-faced hammer, lightly tap the intake valve stem tip to ensure a proper fit.
Be careful not to damage the intake valve stem tip.
Be careful not to tap the retainer.
13715
5.INSTALL EXHAUST VALVE
| *a | 30 mm (1.18 in.) or more |
Sufficiently apply engine oil to the tip area of the exhaust valve shown in the illustration.
| *1 | Inner Compression Spring |
| *2 | Valve Spring Retainer |
| *3 | Cylinder Head Sub-assembly |
| *a | Upper Side |
Install the exhaust valve, inner compression spring and valve spring retainer to the cylinder head sub-assembly.
Install the inner compression spring with its taper side facing upward (towards the valve spring retainer)
Install the same parts to their original positions.
| *a | Wooden Block |
Using SST and wooden blocks, compress the inner compression spring and install the 2 valve spring retainer locks.
Using a plastic-faced hammer, lightly tap the exhaust valve stem tip to ensure a proper fit.
Be careful not to damage the exhaust valve stem tip.
Be careful not to tap the retainer.
13716
6.INSTALL VALVE STEM CAP
Apply a light coat of engine oil to the valve stem caps.
Install the valve stem caps to the cylinder head sub-assembly.