Home › Engine / Hybrid System › 2NR-VE ENGINE MECHANICAL › CYLINDER BLOCK › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042274 2NR-VE ENGINE MECHANICAL _0196196 CYLINDER BLOCK A

2NR-VE ENGINE MECHANICAL  CYLINDER BLOCK  REASSEMBLY  


PROCEDURE

Hide 15708 1.INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.
A363016

Using a 5 mm socket hexagon wrench, install the 4 No. 1 oil nozzle sub-assemblies with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 13101 2.INSTALL PISTON WITH PIN SUB-ASSEMBLY

NOTICE:

If the piston pin has been removed from the piston, replace the piston, piston pin and connecting rod with new ones.


a.

Gradually heat a new connecting rod to 80 °C (176 °F) or more.


b.
A363031C01
1.083,1.302 1.75,2.042 1.75,2.042 2.51,1.479 true 1.156,3.521 1.813,4.344 1.813,4.344 2.521,4.021 true 1.76,4.396 2.073,4.552 0.313,0.156 10 false *a 1.677,2.094 1.99,2.25 0.313,0.156 10 false *a
*a Front Mark


Coat a new piston pin and pin holes of a new piston with engine oil.


c.

Align the front mark of the piston with that of the connecting rod.


d.

Using SST, press in the piston pin.

SST
09221-25026  (09221-00021, 09221-00030, 09221-00090, 09221-00100, 09221-00150)

A363032C01
4.167,0.781 4.469,0.781 false 4.49,1.229 4.708,1.229 false 6.51,1.49 6.729,1.49 false 3.417,1.115 3.594,1.115 3.594,1.115 3.958,1.24 true 6.083,1.635 6.333,2.219 6.333,2.219 6.49,2.219 true 6.281,1.594 6.479,1.927 6.479,1.927 6.635,1.927 true 2.885,1.719 3.115,1.719 true 5.833,1.656 5.417,1.771 5.417,1.771 5.854,1.406 true 0.615,0.823 0.833,0.823 false 0.594,1.344 0.813,1.344 false 0.583,1.771 0.802,1.771 false 2.688,0.542 2.906,0.542 false 2.729,2.073 2.948,2.073 false 4.531,0.708 4.844,0.865 0.313,0.156 10 false *1 3.229,1.052 3.542,1.208 0.313,0.156 10 false *2 4.771,1.156 5.083,1.313 0.313,0.156 10 false *3 3.177,1.625 3.49,1.781 0.313,0.156 10 false *a 5.271,1.802 5.583,1.958 0.313,0.156 10 false *b 6.313,0.667 6.625,0.823 0.313,0.156 10 false *c 6.76,1.417 7.073,1.573 0.313,0.156 10 false *3 6.667,1.865 6.979,2.021 0.313,0.156 10 false *1 6.531,2.156 6.844,2.313 0.313,0.156 10 false *2 2.958,0.469 3.417,0.667 0.458,0.198 10 false SST 3,2 3.458,2.198 0.458,0.198 10 false SST 0.302,0.75 0.76,0.948 0.458,0.198 10 false SST 0.281,1.271 0.74,1.469 0.458,0.198 10 false SST 0.271,1.698 0.729,1.896 0.458,0.198 10 false SST
*1 Piston Pin *2 Connecting Rod
*3 Piston - -
*a Front Mark *b Contact
*c 1.35 to 2.65 mm (0.053 to 0.104 in.) - -
V100135

Rear Side - -


NOTICE:
·

Press in the piston pin from the side of the piston with the front mark as shown in the illustration.

·

With the connecting rod fully inserted into the piston end, press in the piston pin until it is flush with the piston surface.




e.

Check the fitting condition between the piston and piston pin by trying to move the piston back and forth on the piston pin.


Hide 13011 3.INSTALL PISTON RING SET

a.
A305910C01
2.458,0.875 2.823,0.875 true 2.302,1.083 2.667,1.083 true 2.448,1.302 2.813,1.302 true 1.271,0.865 1.688,0.271 true 2.885,0.792 3.198,0.948 0.313,0.156 10 false *1 2.719,1.01 3.031,1.167 0.313,0.156 10 false *2 2.865,1.24 3.177,1.396 0.313,0.156 10 false *3 1.75,0.177 2.063,0.333 0.313,0.156 10 false *a
*1 Side Rail (Upper)
*2 Expander Spacer
*3 Side Rail (Lower)
*a Expander Spacer and Side Rail Groove


Install the expander spacer and 2 side rails by hand, as shown in the illustration.


b.
A363033C01
0.333,2.729 0.646,2.885 0.313,0.156 10 false *1 0.333,3.969 0.646,4.125 0.313,0.156 10 false *2
*1 No. 1 Compression Ring
*2 No. 2 Compression Ring
V100135

Upward


Using a piston ring expander, install the No. 1 compression ring and No. 2 compression ring as shown in the illustration.

NOTICE:

Install the No. 2 compression ring with the code mark (T2) facing upward.



c.
A363034C01
2.073,0.917 2.302,0.583 2.302,0.583 2.448,0.583 true 1.615,0.073 1.927,0.229 0.313,0.156 10 false *1 0.688,1.021 1,1.177 0.313,0.156 10 false *2 1.625,1.958 1.938,2.115 0.313,0.156 10 false *3 2.583,1.031 2.896,1.188 0.313,0.156 10 false *4 2.5,0.49 2.813,0.688 0.313,0.198 10 false *a
*1 Side Rail (Upper)
*2 No. 1 Compression Ring and Expander Spacer
*3 Side Rail (Lower)
*4 No. 2 Compression Ring
*a F Mark


Position the piston rings so that the ring ends are as shown in the illustration.

HINT:

The end gap of each piston ring must be positioned as shown in the illustration regardless of the position of the F mark on the piston.



Hide 11711 4.INSTALL CRANKSHAFT BEARING

a.

Install the 5 upper crankshaft bearings to the cylinder block sub-assembly.

A363035C01
4.646,2.844 4.958,3 0.313,0.156 10 false *a 5.375,2.844 5.688,3 0.313,0.156 10 false *b
*a Correct *b Incorrect
V100135

Engine Front - -


NOTICE:
·

Align the oil holes in the crankshaft bearing with the oil holes in the cylinder block sub-assembly.

·

Do not apply engine oil to the crankshaft bearings or the contact surfaces.




b.

Install the lower crankshaft bearing.

i.

Install the 5 lower crankshaft bearings onto the crankshaft bearing cap.


ii.
A198656N02
1.574,2.128 1.703,2.302 0.128,0.175 10 A 1.574,2.712 1.703,2.887 0.128,0.175 10 B

Using a vernier caliper, measure the distance between the crankshaft bearing cap edge and lower crankshaft bearing edge.

Difference between (A) and (B):

0.8 mm (0.0315 in.) or less


NOTICE:

Do not apply engine oil to the crankshaft bearings or the contact surfaces.




Hide 11791 5.INSTALL UPPER CRANKSHAFT THRUST WASHER

a.
A198042C03
1.344,1.083 1.219,1.427 1.219,1.427 1.5,1.156 true 1.094,1.448 1.646,1.813 0.552,0.365 10 *a
*a Oil Grooves


Install the 2 upper crankshaft thrust washers under the No. 3 journal of the cylinder block sub-assembly with the oil grooves facing outward.


b.

Apply engine oil to the 2 upper crankshaft thrust washers.


Hide 13411 6.INSTALL CRANKSHAFT

a.

Apply engine oil to the upper crankshaft bearings, crankshaft journal and install the crankshaft on the cylinder block sub-assembly.


b.

Apply engine oil to the lower crankshaft bearings.


c.
A198657C04
0.594,2.948 1.125,3.302 0.531,0.354 10 *a
*a Number Mark
V100135

Engine Front


Confirm the number marks and install the crankshaft bearing caps and No. 3 crankshaft bearing cap on the cylinder block sub-assembly.


d.

Apply a light coat of engine oil to the threads and under the crankshaft bearing cap set bolts.


e.
A363014

Temporarily install the 10 crankshaft bearing cap set bolts.


f.

Step 1

i.
A363014N02
1.75,0.198 1.906,0.396 0.156,0.198 10 true 1 1.76,1.573 1.917,1.771 0.156,0.198 10 true 2 1.229,0.208 1.385,0.406 0.156,0.198 10 true 3 1.229,1.594 1.385,1.792 0.156,0.198 10 true 4 2.271,0.208 2.427,0.406 0.156,0.198 10 true 5 2.271,1.573 2.427,1.771 0.156,0.198 10 true 6 0.719,0.208 0.875,0.406 0.156,0.198 10 true 7 0.729,1.583 0.885,1.781 0.156,0.198 10 true 8 2.76,0.208 2.917,0.406 0.156,0.198 10 true 9 2.76,1.552 3.042,1.75 0.281,0.198 10 true 10

Uniformly tighten the 10 crankshaft bearing cap set bolts in the order shown in the illustration.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)



g.

Step 2

i.
A302206C04
2.26,0.729 2.635,0.406 true 2.667,0.281 2.979,0.438 0.313,0.156 10 false *a 1.552,0.385 1.865,0.542 0.313,0.156 10 false *b
*a Paint Mark
*b 90°
V100135

Engine Front


Mark the front of the crankshaft bearing cap set bolts with paint.


ii.

Further tighten the crankshaft bearing cap set bolts an additional 90° in the order shown in the previous illustration.



h.

Check that the paint mark is now at a 90° angle to the front.


i.

Check that the crankshaft turns smoothly.


j.

Check the crankshaft thrust clearance.

Click hereEngine / Hybrid System>2NR-VE ENGINE MECHANICAL>CYLINDER BLOCK>INSPECTION


Hide 13041 7.INSTALL CONNECTING ROD BEARING

a.

Install the connecting rod bearing to the connecting rod and connecting rod cap.


b.
A363878N01
1.229,2.031 1.385,2.229 0.156,0.198 10 false A 2.042,2.031 2.198,2.229 0.156,0.198 10 false B

Using a vernier caliper, measure the distance between the connecting rod edge and connecting rod bearing edge.

Difference between (A) and (B):

0.5 mm (0.0197 in.) or less


NOTICE:

Do not apply engine oil to the connecting rod bearings or the contact surfaces.



c.
A363879N01
1.25,2.01 1.406,2.208 0.156,0.198 10 false A 2.063,2 2.219,2.198 0.156,0.198 10 false B

Using a vernier caliper, measure the distance between the connecting rod cap edge and connecting rod bearing edge.

Difference between (A) and (B):

0.5 mm (0.0197 in.) or less


NOTICE:

Do not apply engine oil to the connecting rod bearings or the contact surfaces.



Hide 8.INSTALL PISTON SUB-ASSEMBLY WITH CONNECTING ROD

a.

Apply engine oil to the cylinder walls, the pistons, and the surfaces of the connecting rod bearings.


b.
A363034C01
2.073,0.917 2.302,0.583 2.302,0.583 2.448,0.583 true 1.615,0.073 1.927,0.229 0.313,0.156 10 false *1 0.688,1.021 1,1.177 0.313,0.156 10 false *2 1.625,1.958 1.938,2.115 0.313,0.156 10 false *3 2.583,1.031 2.896,1.188 0.313,0.156 10 false *4 2.5,0.49 2.813,0.688 0.313,0.198 10 false *a
*1 Side Rail (Upper)
*2 No. 1 Compression Ring and Expander Spacer
*3 Side Rail (Lower)
*4 No. 2 Compression Ring
*a F Mark


Position the piston rings so that the ring ends are as shown in the illustration.

HINT:

The end gap of each piston ring must be positioned as shown in the illustration regardless of the position of the F mark on the piston.



c.
A363036C01
2.677,4.063 1.438,3.448 1.438,3.448 2.625,2.677 true 1.26,3.354 1.573,3.51 0.313,0.156 10 false *a
*a Front Mark


Using a piston ring compressor, push the correctly numbered piston sub-assembly with connecting rod sub-assembly into the cylinder block sub-assembly with the front mark of the piston facing forward.

NOTICE:
·

When inserting the piston with pin sub-assembly with connecting rod, do not allow it to make contact with the No. 1 oil nozzle sub-assembly.

·

Match the numbered connecting rod cap with the connecting rod.




d.
A363017C01
0.698,0.188 1.042,0.333 true 0.5,0.083 0.813,0.24 0.313,0.156 10 false *a
*a Front Mark


Check that the front mark of the connecting rod cap is facing in the correct direction.


e.

Apply a light coat of engine oil to the threads and under the heads of the connecting rod bolts.


f.

Install the connecting rod bolts.


g.

Step 1

i.
A198665N06
2.339,0.277 2.634,0.433 0.295,0.156 10 SST 1.66,0.952 2.157,0.368 2.157,0.368 2.306,0.368 false

Using SST, install and alternately tighten the connecting rod bolts of the connecting rod cap in several steps.

SST
09205-16010  

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)



h.

Step 2

i.
A304509C13
2.083,0.729 2.417,0.333 2.417,0.333 2.667,0.333 true 1.115,0.448 1.427,0.604 0.313,0.156 10 false *b 2.729,0.26 3.042,0.417 0.313,0.156 10 false *a
*a Paint Mark
*b 90°
V100135

Engine Front


Mark the front of the connecting rod bolts with paint.


ii.

Further tighten the connecting rod bolts an additional 90° as shown in the illustration.


iii.

Check that the paint mark is now at a 90° angle to the front.



i.

Check that the crankshaft turns smoothly.


j.

Check the connecting rod thrust clearance.

Click hereEngine / Hybrid System>2NR-VE ENGINE MECHANICAL>CYLINDER BLOCK>INSPECTION


Hide 13521A 9.INSTALL CRANKSHAFT TIMING GEAR KEY

a.

Install the crankshaft timing gear key to the crankshaft.