Home › Engine / Hybrid System › 2NR-VE FUEL › FUEL SYSTEM › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042276 2NR-VE FUEL _0196203 FUEL SYSTEM L

2NR-VE FUEL  FUEL SYSTEM  PRECAUTION  


PRECAUTION


a.

Before working on the fuel system, disconnect the cable from the negative battery terminal.


b.

Do not work on the fuel system near any naked flames. Never smoke during the work.


c.

Keep rubber and leather parts away from gasoline.



DISCHARGE FUEL SYSTEM PRESSURE


CAUTION:
·

Before removing the fuel system parts, take precautions to prevent gasoline spillage.

·

As some pressure remains in the fuel line even after taking precautions to prevent gasoline spillage, use a piece of cloth to prevent gasoline splashes when disconnecting the fuel line.



a.
A359801

Disconnect the fuel pump connector.


b.

Start the engine.


c.

After the engine has stopped on its own, turn the ignition switch off.


d.

Crank the engine again, and check that the engine does not start.


e.

Remove the fuel tank cap, and discharge the pressure in the fuel tank completely.


f.

Disconnect the cable from the negative battery terminal.


g.

Connect the fuel pump connector.



FUEL SYSTEM


a.

When disconnecting a high-pressure fuel line, a large amount of fuel will spray. Perform the following procedure.

i.

Discharge fuel system pressure.


ii.

Disconnect the fuel tube.


iii.

Drain the fuel remaining inside the fuel tube into a container.


iv.
A126529C06
1.76,1.458 1.615,1.708 false 1.5,3.802 1.365,4.052 false 1.49,1.74 1.677,1.896 0.188,0.156 10 false *1 0.146,0.094 0.469,0.302 0.323,0.208 12 false *A: 1.219,4.104 1.406,4.26 0.188,0.156 10 false *1 0.146,2.333 0.469,2.542 0.323,0.208 12 false *B:
*A Fuel Main Tube Side
*B Fuel Pump Tube Side
*1 Plastic Bag


Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



b.

Take the following precautions when removing the fuel tube connector (Type A).

i.

Check the fuel tube connector and fuel main tube for dirt and mud before removing the fuel tube connector.

If dirty, wipe it with a piece of cloth.


ii.
A265503C03
1.552,0.979 1.844,0.979 false 1.865,0.885 2.042,1.052 0.177,0.167 10 *1
*1 Retainer
V100135

Pinch
V100136

Pull out


Disengage the claw and push down the retainer as illustrated.


iii.

Pull the fuel tube connector out of the fuel main tube.


iv.
A126534

If the fuel tube connector and fuel main tube are stuck, pinch the fuel main tube, then push and pull the fuel tube connector to release and disconnect the fuel tube connector.

NOTICE:

Never use any tools.



v.

After removing the fuel tube connector, check the sealing surface of the fuel main tube for dirt and mud.

If dirty, wipe it with a piece of cloth.


vi.

Cover the disconnected fuel tube connector and fuel main tube with plastic bags to prevent damage and the intrusion of foreign objects.



c.

Take the following precautions when installing the fuel tube connector (Type A).

i.
A265511C04
2.094,0.406 2.323,0.406 false 2.365,0.323 2.583,0.49 0.219,0.167 10 *1
*1 Retainer
V100135

Push


Insert the fuel tube connector until it comes into contact with the fuel main tube, then push in the retainer until it makes a "click" sound.

HINT:

If connecting the tubes is too tight, apply a light coat of fresh engine oil to the tip of the fuel main tube.



ii.
A265504

After connecting the fuel tube connector, check that the fuel tube connector and fuel main tube are securely connected by pulling them.



d.

Take the following precautions when removing the fuel tube connector (Type B).

i.
A126537C03
0.74,0.813 0.49,1.198 true 0.365,1.198 0.552,1.354 0.188,0.156 10 *1
*1 Retainer
V100135

Pinch
V100136

Pull out


Check the fuel tube connector and fuel pump tube for dirt and mud before removing the fuel tube connector.

If dirty, wipe it with a piece of cloth.


ii.

Pinch the retainer as illustrated to unlock it, then pull the fuel tube connector out of the fuel pump tube.

NOTICE:

If the retainer is removed from the fuel pump tube, be sure to replace the fuel suction tube with a new one.



iii.
A126538

If the fuel tube connector and fuel pump tube are stuck, pinch the retainer, then push and pull the fuel tube connector to release and disconnect the fuel tube connector.

NOTICE:

Never use any tools.



iv.

After removing the fuel tube connector, check the sealing surface of the fuel pump tube for dirt and mud.

If dirty, wipe it with a piece of cloth.


v.

Cover the disconnected fuel tube connector and fuel pump tube with plastic bags to prevent damage and intrusion of foreign objects.



e.

Take the following precautions when installing the fuel tube connector (Type B).

i.
A265505C01
1.066,0.307 1.252,0.468 0.186,0.161 10 *1 1.541,0.744 1.256,0.461 false
*1 Retainer
V100135

Pinch
V100136

Pull out


Align a new fuel suction tube (fuel tube connector) with the fuel pump tube, then push in the fuel suction tube until the retainer makes a click sound. Then pull out the checker.

NOTICE:

If the retainer is removed from the fuel pump tube, be sure to replace the fuel suction tube with a new one.


HINT:

If connecting the tubes is too tight, apply a light coat of fresh engine oil to the tip of the fuel pump tube.



ii.
A265506

After connecting the fuel tube connector, check that the fuel tube connector and fuel pump tube are securely connected by pulling them.



f.

Take the following precautions when removing the fuel tube connector (Type C).

i.
A360461C01
0.292,0.146 0.625,0.292 0.333,0.146 10 false *a 1.625,0.104 2.031,0.25 0.406,0.146 10 false *b
*a Fuel Tank to Canister Tube Sub-assembly Side
*b Fuel Delivery Pipe Side


Remove the 2 EFI fuel pipe clamps.


ii.

Check for dirt or other foreign matter on the parts to be disconnected and clean them if necessary.


iii.
A159424C07
2.542,1.479 2.677,1.188 2.677,1.188 2.469,1.26 true 2.25,3.042 2.625,3.385 true 2.177,3.729 2.115,3.938 2.115,3.938 2.01,3.74 true 2.698,1.063 3.302,1.417 0.604,0.354 10 *1 2.104,2.938 2.281,3.094 0.177,0.156 10 *1 2.031,3.969 2.198,4.146 0.167,0.177 10 *2
*1 Retainer
*2 O-ring
V100135

Pinch
V100136

Pull


Pinch the retainer of the fuel tube connector, and then pull out the fuel tube connector to disconnect the fuel tube from the fuel pipe.

NOTICE:

Do not use any tools.



iv.
A193370C12
3.333,2.167 3.417,2.167 false
V100135

Pull
V100136

Push


If the connector and pipe are stuck, pinch the retainer with your hand, and then push and pull the connector to disconnect them.

NOTICE:

Do not use any tools.



v.

Check for dirt or other foreign matter on the parts to be disconnected and clean them if necessary.


vi.
A158902C17
1.219,1.635 1.688,1.302 false 1.063,1.615 1.229,1.781 0.167,0.167 10 false *1
*1 Plastic Bag


Protect the contact surface by covering it with a plastic bag.

NOTICE:

Do not damage the pipe or fuel tube connector, and prevent entry of foreign objects.




g.
A125134C07
3.344,2.167 3.427,2.167 false
V100135

Push


Observe the following precautions when connecting the fuel tube connector.

i.

Check that there is no damage or foreign matter on the part of the pipe that comes into contact with the connector.


ii.

Align the axis of the connector with the axis of the pipe. Push the pipe into the connector until the connector makes a click sound. If the connection is too tight, apply a small amount of fresh engine oil to the tip of the pipe.


iii.
A125201C07
3.344,2.167 3.427,2.167 false
V100135

Pull


After connecting the pipe and connector, try to pull them apart to confirm that they are securely connected.


iv.

Inspect for fuel leaks.




INJECTOR


a.
A280208C07
0.146,0.125 3.271,1.365 3.125,1.24 0.146,1.479 3.271,3.146 3.125,1.667 0.865,0.813 0.865,1.115 false 1.438,1.073 1.438,1.167 false 0.854,2.26 0.854,2.688 false 1.438,2.531 1.438,2.677 false 0.552,2.208 0.552,2.656 false 0.552,0.813 0.552,1.115 false 0.5,1.135 0.677,1.281 0.177,0.146 10 false *1 0.792,1.146 0.938,1.313 0.146,0.167 10 false *2 1.365,1.177 1.542,1.333 0.177,0.156 10 false *3 0.24,0.188 0.427,0.344 0.188,0.156 10 false *a 0.24,1.552 0.417,1.719 0.177,0.167 10 false *b 0.49,2.719 0.667,2.865 0.177,0.146 10 false *1 0.792,2.719 0.938,2.885 0.146,0.167 10 false *2 1.365,2.708 1.542,2.865 0.177,0.156 10 false *3
*1 Fuel Injector Assembly
*2 O-ring
*3 Fuel Delivery Pipe
*a OK
*b NG


Take the following precautions when removing and installing the fuel injector assemblies.

i.

Do not reuse the O-ring.


ii.

Do not damage a new O-ring when installing it onto the fuel injector assembly.


iii.

Before installing a new O-ring, apply appropriate lubricant or gasoline.

NOTICE:

Do not use engine oil, gear oil or brake oil.



iv.
A281787C01
2.875,0.833 3.031,0.99 3.031,0.99 3.135,0.99 false 2.344,0.76 2.531,0.958 2.531,0.958 2.531,1.115 false 1.333,1.781 1.521,1.958 1.521,1.958 1.635,1.958 false 3.198,0.885 3.406,1.083 0.208,0.198 10 *1 2.469,1.135 2.719,1.333 0.25,0.198 10 *2 1.677,1.875 1.979,2.073 0.302,0.198 10 *3
*1 Fuel Delivery Pipe
*2 O-ring
*3 Injector Vibration Insulator


Install the fuel injector assembly onto the fuel delivery pipe and cylinder head sub-assembly as illustrated.

NOTICE:

Apply appropriate lubricant or spindle oil to the contact surface of the fuel delivery pipe before installing the fuel injector assembly.





INSPECT FOR FUEL LEAK


a.

Check that there is no fuel leakage after doing maintenance on the fuel system.