Home › Engine / Hybrid System › 2NR-VE EMISSION CONTROL › CANISTER › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042278 2NR-VE EMISSION CONTROL _0196215 CANISTER G

2NR-VE EMISSION CONTROL  CANISTER  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 77740 1.INSPECT CHARCOAL CANISTER ASSEMBLY (for Fuel Tank Cap Method)


b.

Check for clogs in the air filter (when not using GTS or Techstream).

i.

Start the engine.


ii.

Warm up the engine.


iii.

Allow the engine to idle after the engine has warmed up.


iv.

After 15 minutes, open the fuel tank cap assembly to discharge the pressure in the fuel tank assembly.


v.

Close the fuel tank cap assembly and allow the engine to idle for 30 seconds.


vi.
A202994

Open the fuel tank cap assembly again and check for inhalation sounds.

OK:

No whooshing sounds (inhalation sounds) are heard.


HINT:

If there is a smell of gasoline and a whooshing sound (exhalation sound) is heard, positive pressure in the fuel tank assembly is being discharged. This does not indicate a malfunction.




c.

Check for clogs in the air filter (when using the GTS or Techstream).

i.

Connect the GTS or Techstream to the DLC3.


ii.

Start the engine.


iii.

Turn the GTS or Techstream on.


iv.

Enter the following menus: Powertrain / EFI / Active Test / Purge VSV.


v.

Open the fuel tank cap assembly to discharge the pressure in the fuel tank assembly.


vi.

Perform the "Purge VSV" Active Test while the engine is idling.


vii.

Close the fuel tank cap assembly and allow the engine to idle for 30 seconds.


viii.

Open the fuel tank cap assembly again and check for inhalation sounds.

OK:

No whooshing sounds (inhalation sounds) are heard.


HINT:

If there is a smell of gasoline and a whooshing sound (exhalation sound) is heard, positive pressure in the fuel tank assembly is being discharged. This does not indicate a malfunction.




Hide 77740 2.INSPECT CHARCOAL CANISTER ASSEMBLY (for Vacuum Measurement Method)

a.

Visually check the charcoal canister for airtightness.

i.

Visually check the charcoal canister for cracks or damage, and check that there is no gasoline smell.



b.

Inspect the check valve.

i.

Disconnect the fuel emission hose.


ii.
A361118C01
0.833,0.396 1.479,0.635 true 0.646,0.302 0.958,0.458 0.313,0.156 10 false *a 0.635,1.25 0.948,1.406 0.313,0.156 10 false *b
*a Port A
*b Air


Apply the compressed air from the port A.

OK:

Air enters the canister through port A.



iii.
A361119C01
2.49,2.406 2.646,1.99 2.646,1.99 2.906,1.99 false 0.458,0.406 1.177,0.531 true 0.26,0.302 0.573,0.458 0.313,0.156 10 false *a 2.958,1.906 3.271,2.063 0.313,0.156 10 false *b
*a Port A
*b Vacuum Pump


Apply a vacuum from the port A, using a vacuum pump.

OK:

The vacuum is maintained at first. By gradually increasing the vacuum, air flows and the vacuum decreases after the vacuum reaches the specified level.





d.
A363875C01
0.979,1.365 0.729,1.198 true 0.833,2.969 0.698,2.792 true 0.979,0.885 0.594,0.844 true 1.281,3.427 1.167,3.115 true 1.146,0.75 0.802,0.625 true 1.688,3.51 1.479,3.24 true 2.302,0.104 2.073,0.188 true 2.458,2.542 2.229,2.625 true 0,0 0.469,0.396 0.469,0.396 10 false *A 0.052,2.469 0.438,2.781 0.385,0.313 10 false *B 1.031,1.354 1.281,1.552 0.25,0.198 10 true *1 0.99,0.823 1.25,1.01 0.26,0.188 10 true *a 1.188,0.698 1.458,0.906 0.271,0.208 10 true *b 0.552,2.646 0.802,2.844 0.25,0.198 10 true *1 1.281,3.438 1.542,3.656 0.26,0.219 10 true *a 1.708,3.5 1.979,3.708 0.271,0.208 10 true *b 2.344,0.01 2.656,0.167 0.313,0.156 10 false *c 2.51,2.427 2.823,2.583 0.313,0.156 10 false *c
*A for LHD
*B for RHD
*1 Fuel Emission Hose
*a 3-way Connector
*b Hose
*c Vacuum Pump


Check for clogs in the air filter (when not using GTS or Techstream).

i.

As shown in the illustration, connect the fuel emission hose to the canister via the 3-way connector, hose and vacuum pump.


ii.

Start the engine.


iii.

Warm up the engine.


iv.

Allow the engine to idle after the engine has warmed up.


v.

After 15 minutes, check the indicator needle on the vacuum pump.

OK:

Indicator needle of vacuum pump does not rise from its initial position.


HINT:

The indicator needle may shake due to engine vibration, etc., but if it immediately returns to its initial position, there is no problem.




e.
A363875C01
0.979,1.365 0.729,1.198 true 0.833,2.969 0.698,2.792 true 0.979,0.885 0.594,0.844 true 1.281,3.427 1.167,3.115 true 1.146,0.75 0.802,0.625 true 1.688,3.51 1.479,3.24 true 2.302,0.104 2.073,0.188 true 2.458,2.542 2.229,2.625 true 0,0 0.469,0.396 0.469,0.396 10 false *A 0.052,2.469 0.438,2.781 0.385,0.313 10 false *B 1.031,1.354 1.281,1.552 0.25,0.198 10 true *1 0.99,0.823 1.25,1.01 0.26,0.188 10 true *a 1.188,0.698 1.458,0.906 0.271,0.208 10 true *b 0.552,2.646 0.802,2.844 0.25,0.198 10 true *1 1.281,3.438 1.542,3.656 0.26,0.219 10 true *a 1.708,3.5 1.979,3.708 0.271,0.208 10 true *b 2.344,0.01 2.656,0.167 0.313,0.156 10 false *c 2.51,2.427 2.823,2.583 0.313,0.156 10 false *c
*A for LHD
*B for RHD
*1 Fuel Emission Hose
*a 3-way Connector
*b Hose
*c Vacuum Pump


Check for clogs in the air filter (when using the GTS or Techstream).

i.

As shown in the illustration, connect the fuel emission hose to the canister via the 3-way connector, hose and vacuum pump.


ii.

Connect the GTS or Techstream to the DLC3.


iii.

Start the engine.


iv.

Turn the GTS or Techstream on.


v.

Enter the following menus: Powertrain / EFI / Active Test / Purge VSV.


vi.

Perform the "Purge VSV" Active Test while the engine is idling.


vii.

Check the indicator needle on the vacuum pump.

OK:

Indicator needle of vacuum pump does not rise from its initial position.


HINT:

The indicator needle may shake due to engine vibration, etc., but if it immediately returns to its initial position, there is no problem.