Home › Engine / Hybrid System › 1NR-VE INTAKE / EXHAUST › EXHAUST PIPE › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042279 1NR-VE INTAKE / EXHAUST _0196222 EXHAUST PIPE A

1NR-VE INTAKE / EXHAUST  EXHAUST PIPE  INSTALLATION  


PROCEDURE

Hide 17451 1.INSTALL EXHAUST PIPE GASKET

a.
A181728C92
2.813,1.563 2.688,1.563 2.688,1.563 2.385,1.875 true 1.615,3.188 1.99,3.188 1.99,3.188 1.99,2.313 true 1.458,0.656 1.813,0.656 1.813,0.656 1.813,1.115 false 1.313,0.563 1.604,0.781 0.292,0.219 10 false *1 2.854,1.49 3.135,1.698 0.281,0.208 10 false *a 1.448,3.104 1.771,3.344 0.323,0.24 10 false *2
*1 Exhaust Manifold Converter Sub-assembly
*2 Exhaust Pipe Gasket
*a Wooden Block


Using a plastic hammer and wooden block, tap in a new exhaust pipe gasket until its surface is flush with the exhaust manifold converter sub-assembly.

NOTICE:
·

Be sure to install the exhaust pipe gasket in the correct direction.

·

Do not reuse the exhaust pipe gasket.

·

Do not damage the exhaust pipe gasket.

·

Do not push in the exhaust pipe gasket by using the exhaust pipes when connecting it.




Hide 17410 2.SET FRONT EXHAUST PIPE ASSEMBLY

a.

Set the position where the front exhaust pipe assembly can be installed.


Hide 58151A 3.INSTALL NO. 1 FLOOR HEAT INSULATOR

a.

Install the No. 1 floor heat insulator with the 2 bolts.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


Hide 17410 4.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.
A128853

Using a vernier caliper, measure the free length of the compression springs.

Minimum 41.1 mm (1.62 in.)

If the free length is less than the minimum, replace the compression spring.


b.
A361328C01
2.656,0.76 2.948,0.615 false 2.708,0.99 2.948,1.167 false 2.281,0.958 2.458,0.344 true 2.958,0.5 3.271,0.698 0.313,0.198 10 false *1 2.958,1.156 3.271,1.354 0.313,0.198 10 false *2 2.479,0.198 2.792,0.396 0.313,0.198 10 false *3 0.5,1.5 0.813,1.698 0.313,0.198 10 false *a
*1 Exhaust Manifold Converter Sub-assembly
*2 Front Exhaust Pipe Assembly
*3 Exhaust Pipe Gasket
*a Space Between Flanges: 8.5 mm (0.335 in.)


Install the front exhaust pipe assembly with the 2 bolts and 2 compression springs.

Torque:
46.5 N*m (474 kgf*cm, 34 ft.*lbf)

HINT:

After installation, check that the space between the flanges of the exhaust manifold converter sub-assembly and front exhaust pipe assembly is consistent front-to-rear and left-to-right.



c.

Connect the No. 2 exhaust pipe support.


Hide 17451 5.INSTALL EXHAUST PIPE GASKET

a.

Install a new exhaust pipe gasket to the front exhaust pipe assembly.


Hide 17430 6.INSTALL TAIL EXHAUST PIPE ASSEMBLY

a.

Connect the tail exhaust pipe assembly with the 2 No. 2 exhaust pipe support and No. 3 exhaust pipe support.


b.

Install the tail exhaust pipe assembly with the 2 bolts and 2 new nuts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide 7.INSPECT FOR EXHAUST GAS LEAK