Home › Engine / Hybrid System › 2NR-VE COOLING › COOLANT › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042282 2NR-VE COOLING _0196237 COOLANT A

2NR-VE COOLING  COOLANT  REPLACEMENT  


PROCEDURE

Hide 51473A 1.REMOVE ENGINE SIDE COVER SUB-ASSEMBLY RH

a.
A359827

Remove the clip and engine side cover sub-assembly RH.


Hide 2.DRAIN ENGINE COOLANT

CAUTION:

Do not remove the radiator cap sub-assembly, air-bleeding valve or radiator drain cock plug while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.


a.

Loosen the radiator drain cock plug.


b.

Remove the radiator cap sub-assembly.


c.

Loosen the radiator drain cock plug, then drain the coolant.

A360749C01
1.885,1.26 2.177,0.979 2.177,0.979 2.385,0.979 false 5.542,2.063 5.948,0.917 5.948,0.917 6.156,0.917 true 0.385,3.823 0.594,3.823 0.594,3.823 0.833,3.302 true 6.25,0.844 6.563,1 0.313,0.156 10 false *1 0.188,3.74 0.5,3.896 0.313,0.156 10 false *2 2.448,0.885 2.76,1.042 0.313,0.156 10 false *3
*1 Air-Bleeding Valve *2 Radiator Drain Cock Plug
*3 Radiator Cap Sub-assembly - -



Hide 3.ADD ENGINE COOLANT

a.

Tighten the radiator drain cock plug by hand.


b.

Install the vinyl tube to the air-bleeding valve.


c.
A359828C01
2.24,0.74 2.323,0.51 2.323,0.51 2.521,0.51 true 2.594,0.427 2.906,0.583 0.313,0.156 10 true *1
*1 Air-Bleeding Valve


Loosen the air-bleeding valve.


d.

Add engine coolant from the radiator filler.

Standard Capacity (w/o Heater):

4.2 liters (4.4 US qts, 3.7 Imp. qts) for Automatic Transmission

4.3 liters (4.5 US qts, 3.8 Imp. qts) for Manual Transmission


Standard Capacity (w/ Heater):

4.5 liters (4.8 US qts, 4.0 Imp. qts) for Automatic Transmission

4.6 liters (4.9 US qts, 4.0 Imp. qts) for Manual Transmission


Standard Capacity (for Tropic):

5.1 liters (5.4 US qts, 4.5 Imp. qts) for Automatic Transmission

5.2 liters (5.5 US qts, 4.6 Imp. qts) for Manual Transmission


NOTICE:

Do not substitute plain water for engine coolant.


HINT:

TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).



e.

Tighten the air-bleeding valve when the coolant overflows from the air-bleeding valve.

NOTICE:

If the coolant does not overflow from the air-bleeding valve, tighten the valves after the coolant overflows from the radiator assembly.



f.

Remove the vinyl tube from the air-bleeding valve.


g.

Install the radiator cap sub-assembly when the coolant overflows from the radiator assembly.

HINT:

Observe the coolant level inside the radiator by squeezing the No. 1 radiator hose and No. 2 radiator hose several times by hand. If the coolant level goes down, add coolant.



h.

Fill the radiator reservoir tank with coolant up to the full level.


i.

Start the engine and keep the engine speed at 2000 rpm. Warm up the engine until the cooling fan operates twice.

HINT:

When warming up the engine, squeeze the radiator No. 1 radiator hose and No. 2 radiator hose a few times.



j.

Stop the engine, then wait until the coolant cools down. Remove the radiator cap and check the coolant level.


k.

If the coolant level goes down, fill the radiator with coolant. If the coolant level is low, add coolant to the radiator reservoir tank FULL line.

Click hereEngine / Hybrid System>2NR-VE COOLING>COOLING SYSTEM>ON-VEHICLE INSPECTION


Hide 51473A 5.INSTALL ENGINE SIDE COVER SUB-ASSEMBLY RH

a.

Install the engine side cover sub-assembly RH with the clip.