Home › Engine / Hybrid System › 1NR-VE LUBRICATION › OIL AND OIL FILTER › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042283 1NR-VE LUBRICATION _0196244 OIL AND OIL FILTER A

1NR-VE LUBRICATION  OIL AND OIL FILTER  REPLACEMENT  


CAUTION / NOTICE / HINT

CAUTION:
·

Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

·

Wear protective clothing and gloves. Avoid contact with used oil. If contact occurs, wash your skin thoroughly with soap or waterless hand cleaner. Never use gasoline, thinners, or solvents to wash the skin.

·

In order to protect the environment, dispose of used oil and used oil filters at designated disposal sites only.



PROCEDURE

Hide 12108 1.REMOVE OIL FILLER CAP SUB-ASSEMBLY

A361317

a.

Remove the oil filler cap sub-assembly.


Hide 51474 2.REMOVE ENGINE SIDE COVER SUB-ASSEMBLY LH

A361318

a.

Remove the 2 clips and engine side cover sub-assembly LH.


Hide 3.DRAIN ENGINE OIL

a.

Remove the oil pan drain plug and gasket, and drain the engine oil into a container.


b.

Clean and install a new gasket to the oil pan drain plug.


c.

Install the oil pan drain plug.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 15601 4.REMOVE OIL FILTER SUB-ASSEMBLY

a.
A361319E01
1.385,1.594 1.729,0.917 true 1.094,1.604 1.458,1.865 0.365,0.26 10 true SST

Using SST, loosen the oil filter sub-assembly, and drain the remaining engine oil from the oil filter sub-assembly.

SST
09228-06501  

HINT:

Set a container below the oil filter sub-assembly before loosening oil filter sub-assembly.



b.

Remove the oil filter sub-assembly.


Hide 15601 5.INSTALL OIL FILTER SUB-ASSEMBLY

a.

Apply a small amount of engine oil to the O-ring and temporarily tighten a new oil filter sub-assembly.


b.
A361330E01
1.448,1.292 1.677,0.906 true 1.135,1.271 1.594,1.469 0.458,0.198 10 true SST

Using SST, tighten the oil filter sub-assembly.

SST
09228-06501  

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)


Hide 6.ADD ENGINE OIL

a.

Add new engine oil.

Standard Oil Grade
Oil Grade Oil Viscosity (SAE)
API grade SN "Resource-Conserving" or ILSAC multigrade engine oil 0W-20

Standard Capacity
Item Standard Condition
Drain and refill with oil filter change 3.5 liters (3.7 US qts, 3.1 Imp. qts)
Drain and refill without oil filter change 3.3 liters (3.5 US qts, 2.9 Imp. qts)
Dry fill 4.0 liters (4.2 US qts, 3.5 Imp. qts)


Hide 12108 7.INSTALL OIL FILLER CAP SUB-ASSEMBLY

a.

Install the oil filler cap sub-assembly.


Hide 8.INSPECT FOR ENGINE OIL LEAK

a.

Warm up the engine. Make sure that there are no engine oil leaks from the area that was worked on.


Hide 51474 9.INSTALL ENGINE SIDE COVER SUB-ASSEMBLY LH

a.

Install the engine side cover sub-assembly LH with the 2 clips.