Home › Engine / Hybrid System › 1NR-VE STARTING › STARTER(for Manual Transmission) › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042285 1NR-VE STARTING _0196253 STARTER(for Manual Transmission) G

1NR-VE STARTING  STARTER(for Manual Transmission)  INSPECTION  


PROCEDURE

Hide 28100 1.INSPECT STARTER ASSEMBLY

NOTICE:

The following tests must be performed within 5 seconds to prevent the coil from burning out.


a.

Perform a pull-in test.

i.
A359655C02
1.938,1.927 2.354,1.51 true 2.656,0.615 2.823,0.313 2.823,0.313 3.073,0.313 false 1.781,1.906 1.969,2.083 0.188,0.177 10 false *1 3.115,0.24 3.302,0.385 0.188,0.146 10 false *2
*1 Terminal 50
*2 Starter Body


Connect the battery to the repair service starter kit and starter body as shown in the illustration.Check that the clutch pinion gear is extended.

If the clutch pinion gear does not move, replace the repair service starter kit.



b.
A359656C02
2.74,0.583 2.917,0.323 2.917,0.323 3.115,0.323 true 1.938,1.927 2.354,1.51 true 1.771,1.906 1.969,2.094 0.198,0.188 10 false *1 3.167,0.229 3.333,0.396 0.167,0.167 10 false *2
*1 Terminal 50
*2 Starter Body


Inspect the clutch pinion gear return.

i.

Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear returns.

If the clutch pinion gear does not return inward, replace the repair service starter kit.



c.

Perform a no-load performance test.

i.

Fix the starter assembly in a vise between aluminum plates.

NOTICE:

Do not clamp the vise too tightly.



ii.
A359657C02
2.25,1.75 2.354,1.49 true 2.667,0.604 2.729,0.333 2.729,0.333 2.958,0.333 true 2.896,1.917 2.646,1.313 true 2.385,2.708 2.042,2.708 false 2.135,1.76 2.448,1.917 0.313,0.156 10 false *1 2.854,1.969 3.167,2.125 0.313,0.156 10 false *2 3,0.25 3.313,0.406 0.313,0.156 10 false *3 2.427,2.625 2.74,2.781 0.313,0.156 10 false *a
*1 Terminal 50
*2 Terminal 30
*3 Starter Body
*a Ammeter


Connect the battery and an ammeter to the starter assembly and starter body as shown in the illustration.


iii.

Check that the starter rotates smoothly and steadily with the clutch pinion gear extended.

Measure the current according to the value(s) in the table below.

Standard Current:
Tester Connection Condition Specified Condition
Battery Positive Terminal - Terminal 30 - Terminal 50
Battery Negative Terminal - Starter Body
11.5 V Below 90 A


If the result is not as specified, replace the starter assembly.



Hide 28160 2.INSPECT STARTER ARMATURE ASSEMBLY

a.
A247248C12
1.427,1.781 2.052,1.198 true 1.25,1.75 1.521,2 0.271,0.25 10 false *1
*1 Segment


Check the commutator for an open circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Segment Always Below 1 Ω


If the result is not as specified, replace the starter armature assembly.



b.

Check the commutator for a short to ground.

i.
A247247C10
2.365,0.865 2.875,0.417 true 0.698,1.281 1.208,0.833 true 2.896,0.292 3.083,0.448 0.188,0.156 10 false *1 0.542,1.219 0.854,1.375 0.313,0.156 10 false *2
*1 Segment
*2 Coil Core


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Coil Core Always 10 kΩ or higher


If the result is not as specified, replace the starter armature assembly.



c.

Check the commutator surface for dirt and burns.

If the surface is dirty or burnt, restore it with sandpaper (No. 400) or a lathe.


d.
A247250

Check the commutator for circle runout.

i.

Place the commutator on V-blocks.


ii.

Using a dial indicator, measure the circle runout.

Maximum circle runout:

0.05 mm (0.00197 in.)


If the runout is greater than the maximum, replace the starter armature assembly.



e.
A247251

Using a vernier caliper, measure the commutator diameter.

Standard diameter:

25.0 mm (0.9843 in.)


Minimum diameter:

24.0 mm (0.9449 in.)


If the diameter is less than the minimum, replace the starter armature assembly.


f.
A247252C03
3.021,0.823 3.333,0.979 0.313,0.156 10 false *a
*a Depth


Check that the undercut portion between the segments is free of foreign matter and measure its depth.

Standard undercut depth:

0.7 mm (0.0276 in.)


Minimum undercut depth:

0.2 mm (0.0079 in.)


If the undercut depth is less than the minimum, replace the starter armature assembly.


Hide 28140 3.INSPECT STARTER BRUSH HOLDER ASSEMBLY

a.
A296854C02
2.052,0.135 2.365,0.292 0.313,0.156 10 false *a
*a Length


Using a vernier caliper, measure the brush protrusion amount as indicated in the illustration.

Standard length:

8.0 mm (0.3150 in.)


Minimum length:

4.0 mm (0.1575 in.)


If the length is less than the minimum, replace the starter brush holder assembly.


Hide 28021 4.INSPECT STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY

a.
A345082C02
1.948,0.656 2.26,0.813 0.313,0.156 10 false *a 2.115,1.656 2.427,1.813 0.313,0.156 10 false *b
*a Free
*b Lock


Holding the starter center bearing clutch sub-assembly, rotate the clutch pinion gear clockwise, and check that it turns freely. Try to rotate the clutch pinion gear counterclockwise and check that it locks.

If necessary, replace the starter center bearing clutch sub-assembly.


Hide 28226B 5.INSPECT REPAIR SERVICE STARTER KIT

a.
A247243C09
2.292,0.208 2.51,0.208 2.51,0.208 2.51,0.583 false 2.104,0.125 2.25,0.281 0.146,0.156 10 false *1
*1 Plunger


Check the plunger.

i.

Push in the plunger and check that it returns quickly to its original position.

If necessary, replace the repair service starter kit.



b.
A359658C02
2.427,0.667 2.427,0.302 2.427,0.302 2.115,0.302 false 0.552,1.906 0.927,1.906 false 1.948,0.219 2.26,0.375 0.313,0.156 10 false *1 0.375,1.833 0.688,1.99 0.313,0.156 10 false *2
*1 Body
*2 Terminal 50


Check the repair service starter kit for an open circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 - Body Always Below 2 Ω


If the result is not as specified, replace the repair service starter kit.