Home › Engine / Hybrid System › 1NR-VE STARTING › STARTER(for Manual Transmission) › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042285 1NR-VE STARTING _0196253 STARTER(for Manual Transmission) A

1NR-VE STARTING  STARTER(for Manual Transmission)  REASSEMBLY  


PROCEDURE

Hide 28021 1.INSTALL STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY

a.
A248656C08
0,0 0,0 false
V100135

High-temperature Grease


Apply high-temperature grease to the 3 starter planetary gears and the starter center bearing clutch sub-assembly.

HINT:

Apply approximately 0.5 g (0.018 oz) of high-temperature grease in total to the starter planetary gear section, end section, and pins without depressions.



b.
A248654C11
1.156,1.448 0.656,1.552 0.656,1.552 1.271,1.063 true 0.677,1.552 1.5,1.531 true 0.469,1.458 0.781,1.615 0.313,0.156 10 false *a
*a Pins without Depressions


Install the 3 starter planetary gears to the pins without depressions on the starter center bearing clutch sub-assembly.


c.
A296697

Engage the 3 claws and install the starter internal gear to the starter center bearing clutch sub-assembly.


d.
A296814C02
0.479,0.896 0.479,0.458 0.479,0.458 0.688,0.458 false 0.729,0.365 1.042,0.521 0.313,0.156 10 false *1
*1 Starter Drive Lever
V100135

High-temperature Grease


Apply high-temperature grease to the starter drive lever contact surface.

HINT:

Apply approximately 0.1 g (0.004 oz) of high-temperature grease to each section.



e.
A359659C03
1.906,0.885 2.24,0.313 2.24,0.313 2.417,0.313 false 2.521,0.781 2.75,0.438 2.75,0.438 2.948,0.438 false 2.438,0.219 2.75,0.375 0.313,0.156 10 false *a 3,0.375 3.313,0.531 0.313,0.156 10 false *b
*a Depression
*b Protrusion


Align the depression in the starter drive housing assembly with the protrusion on the starter center bearing clutch sub-assembly and install the starter center bearing clutch sub-assembly.


f.

Install the rubber seal to the starter drive housing assembly.


Hide 28140 2.INSTALL STARTER BRUSH HOLDER ASSEMBLY

a.
A248658

Install the starter commutator end frame assembly to the starter brush holder assembly as shown in the illustration.

HINT:

If the attachment location is not correct, the through bolt cannot be attached.



b.
A248796

Spread the brushes on the starter brush holder assembly, and install the starter armature assembly to the starter brush holder assembly.


Hide 28160 3.INSTALL STARTER ARMATURE ASSEMBLY

a.
A297042C01
1.74,0.865 2.063,0.865 false 2.104,0.792 2.417,0.99 0.313,0.198 10 false *a
*a Hammer


Install the starter armature assembly and the starter brush holder assembly while holding down the starter yoke assembly with the handle of a hammer.

HINT:

The starter armature assembly will be attracted by the magnetic field of the starter yoke assembly, so the starter armature assembly is held with the handle of the hammer.



Hide 28120 4.INSTALL STARTER YOKE ASSEMBLY

A359660C02
1.021,0.844 1.021,0.323 1.021,0.323 1.188,0.323 true 1.49,0.698 1.49,0.177 1.49,0.177 1.656,0.177 false 1.219,0.229 1.531,0.385 0.313,0.156 10 false *a 1.688,0.104 2,0.26 0.313,0.156 10 false *b
*a Protrusion
*b Depression


a.

Align the depression in the starter yoke assembly with the protrusion on the starter center bearing clutch sub-assembly.


b.
A359653

Install the starter yoke assembly with the 3 through bolts.

Torque:
3.0 N*m (31 kgf*cm, 27 in.*lbf)


Hide 28226B 5.INSTALL REPAIR SERVICE STARTER KIT

a.
A359652C04
1.469,0.542 1.844,0.542 false 1.677,1.344 1.875,1.344 1.875,1.344 1.875,1.073 false 1.875,0.469 2.073,0.625 0.198,0.156 10 false *1 1.51,1.26 1.698,1.427 0.188,0.167 10 false *2
*1 Starter Drive Lever
*2 Hook


Attach the hook on the starter drive lever.


b.
A359661C02
1.354,2.854 1.354,3.063 1.354,3.063 1.51,3.063 false 1.521,2.979 1.833,3.135 0.313,0.156 10 false *1
*1 Terminal C


Push down the back of the repair service starter kit and connect it to the terminal C.

NOTICE:
·

Connect the repair service starter kit securely to the terminal C.


·

Check that the parts are free of foreign matter, oil, or grease.




c.
A359651

Install the repair service starter kit with the 2 bolts.

Torque:
3.0 N*m (31 kgf*cm, 27 in.*lbf)