Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW REGULATOR MOTOR(for Front Door) › from 2015.08
RM19Y0E _59 Vehicle Exterior _003016 WINDOW / GLASS _0015252 POWER WINDOW REGULATOR MOTOR(for Front Door) G

WINDOW / GLASS  POWER WINDOW REGULATOR MOTOR(for Front Door)  INSPECTION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RHD and LHD vehicles.

·

The procedure listed below is for the LHD vehicle.



PROCEDURE

Hide 85720C 1.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NOTICE:
·

Do not apply positive (+) battery voltage to any terminals other than terminal 1 and terminal 3 to avoid damaging the pulse sensor inside the motor.

·

When a front door window regulator sub-assembly or a power window regulator motor assembly RH is replaced, the power window control system must be initialized (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



a.
B415915C01
0.469,0.531 1.219,1.344 true 1.021,3.281 1.354,3.583 true 2.344,3.292 1.844,3.583 true 0.24,0.417 0.552,0.573 0.313,0.156 10 false *1 2.448,1.26 2.76,1.417 0.313,0.156 10 false *a 2.313,1.698 2.625,1.854 0.313,0.156 10 false *b 0.365,2.771 0.677,2.927 0.313,0.156 10 false *c 2.417,3.104 2.781,3.333 0.365,0.229 10 false U+ 0.854,3.083 1.219,3.313 0.365,0.229 10 false D+
*1 Motor Gear
*a Counterclockwise
*b Clockwise
*c Component without harness connected
(Power Window Regulator Motor Assembly LH)


Check the operation of the power window regulator motor assembly LH.

i.

Apply battery voltage to the power window regulator motor assembly LH and check the operation of the power window regulator motor assembly LH.

Standard:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 1 (U+)
Battery negative (-) → Terminals 3 (D+)
Motor gear rotates counterclockwise
Battery positive (+) → Terminal 3 (D+)
Battery negative (-) → Terminals 1 (U+)
Motor gear rotates clockwise


If the result is not as specified, replace the power window regulator motor assembly LH.



Hide 85710D 2.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

a.
B415916C01
2.979,2.271 2.344,1.406 true 2.302,4.198 1.896,3.719 true 1.042,4.208 1.396,3.719 true 2.969,2.354 3.281,2.51 0.313,0.156 10 false *1 0.885,1.281 1.198,1.438 0.313,0.156 10 false *a 1.031,1.635 1.344,1.792 0.313,0.156 10 false *b 0.688,2.813 1,2.969 0.313,0.156 10 false *c 2.365,4.25 2.75,4.427 0.385,0.177 10 false U+ 0.917,4.24 1.302,4.417 0.385,0.177 10 false D+
*1 Motor Gear
*a Clockwise
*b Counterclockwise
*c Component without harness connected
(Power Window Regulator Motor Assembly RH)


Check the operation of the power window regulator motor assembly RH.

i.

Apply battery voltage to the power window regulator motor assembly RH and check the operation of the power window regulator motor assembly RH.

Standard:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 2 (D+)
Battery negative (-) → Terminal 1 (U+)
Motor gear rotates counterclockwise
Battery positive (+) → Terminal 1 (U+)
Battery negative (-) → Terminal 2 (D+)
Motor gear rotates clockwise


If the result is not as specified, replace the power window regulator motor assembly RH.