Home › Vehicle Exterior › WIPER / WASHER › FRONT WIPER MOTOR › from 2015.08
RM19Y0E _59 Vehicle Exterior _003019 WIPER / WASHER _0015272 FRONT WIPER MOTOR A

WIPER / WASHER  FRONT WIPER MOTOR  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RHD and LHD vehicles.

·

The procedure listed below is for the RHD vehicle.



PROCEDURE

Hide 85292B 1.REMOVE FRONT WIPER ARM HEAD CAP

a.
E252399C02
1.865,1.813 2.167,1.396 true 1.667,1.75 1.979,1.906 0.313,0.156 10 false *1
*1 Protective Tape


Using a screwdriver with its tip wrapped in protective tape, disengage the 3 claws to remove the front wiper arm head cap.

HINT:

Use the same procedure for both sides.



Hide 85211B 2.REMOVE FRONT WIPER ARM AND BLADE RH

a.
E321979

Remove the nut and the front wiper arm and blade RH.


Hide 85221B 3.REMOVE FRONT WIPER ARM AND BLADE LH

a.
E321980

Remove the nut and the front wiper arm and blade LH.


Hide 53445 4.REMOVE HOOD HINGE COVER RH

a.
E321993N02
1.365,0.469 1.521,0.667 0.156,0.198 10 false 1 1.719,1.49 1.875,1.688 0.156,0.198 10 false 2 1.229,2.188 1.385,2.385 0.156,0.198 10 false 2 1.438,1.792 1.594,1.99 0.156,0.198 10 false 3

Disengage the 3 claws and guide in the order shown in the illustration.


b.
E321981

Disengage the clip to remove the hood hinge cover RH indicated by the arrow in the illustration.


Hide 53446 5.REMOVE HOOD HINGE COVER LH

HINT:

Use the same procedure as for the RH side.


Hide 53383 6.REMOVE HOOD TO COWL TOP SEAL

a.

Disengage the 7 clips to remove the hood to cowl top seal.

E324483


Hide 55781E 7.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

a.
E322468

Disconnect the washer hose.


b.

Remove the 2 clips.

E324967


c.

Disengage the 7 claws to separate the cowl top ventilator louver sub-assembly.

E321982

NOTICE:
B332897C01
0.063,0.073 0.375,0.229 0.313,0.156 10 false *a 0.073,2.073 0.385,2.229 0.313,0.156 10 false *b
*a Incorrect
*b Correct


Pushing the claws with a screw driver or your finger may damage them, so disengage the claws by pinching them with your fingers.



d.

Disengage the 9 guides to remove the cowl top ventilator louver sub-assembly as shown in the illustration.

E321983


Hide 8.REMOVE WINDSHIELD WIPER MOTOR AND LINK

a.
E322470

Disconnect the connector.


b.

Remove the 2 bolts.


c.
E322471C02
2.521,2.844 2.729,2.677 true 0.865,2.729 1.042,2.875 true 1.083,2.813 1.396,3.01 0.313,0.198 10 false *1 2.344,2.771 2.656,2.969 0.313,0.198 10 false *1
*1 Grommet


Disengage the grommet to remove the windshield wiper motor and link as shown in the illustration.

NOTICE:

Be careful not to damage the windshield when removing the windshield wiper motor and link.



Hide 85110 9.REMOVE WINDSHIELD WIPER MOTOR ASSEMBLY

a.
E291223C01
0.729,0.771 1.083,1.073 false 1.333,0.927 1.49,0.406 false 2.5,0.708 2.781,0.292 false 0.542,0.667 0.802,0.823 0.26,0.156 10 false *1 2.823,0.219 3.135,0.375 0.313,0.156 10 false *2 1.531,0.302 1.844,0.458 0.313,0.156 10 false *3
*1 Protective Tape
*2 No. 2 Front Wiper Link Rod
*3 Crank Arm Pivot


Using a clip remover with its tip wrapped in protective tape, separate the No. 2 front wiper link rod from the crank arm pivot of the front wiper crank sub-assembly as shown in the illustration.


b.
E291224C02
0.792,0.823 0.448,0.646 false 1.573,0.417 1.969,0.802 true 2.229,0.938 2.521,0.354 true 2.594,0.271 2.906,0.427 0.313,0.156 10 false *1 0.25,0.542 0.563,0.698 0.313,0.156 10 false *2 1.385,0.313 1.698,0.469 0.313,0.156 10 false *3
*1 Protective Tape
*2 No. 1 Front Wiper Link Rod
*3 Crank Arm Pivot


Using a clip remover with its tip wrapped in protective tape, separate the No. 1 front wiper link rod from the crank arm pivot of the front wiper crank sub-assembly as shown in the illustration.


c.
E252413

Using a T30 "TORX" socket wrench, remove the 2 bolts and the windshield wiper motor assembly from the front wiper link assembly.