Home › Vehicle Exterior › WIPER / WASHER › FRONT WIPER MOTOR › from 2015.08
RM19Y0E _59 Vehicle Exterior _003019 WIPER / WASHER _0015272 FRONT WIPER MOTOR A

WIPER / WASHER  FRONT WIPER MOTOR  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RHD and LHD vehicles.

·

The procedure listed below is for the RHD vehicle.



PROCEDURE

Hide 85110 1.INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY

a.

Using a T30 "TORX" socket wrench, install the windshield wiper motor assembly to the front wiper link assembly with the 2 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


b.
E250255C02
0,0 0,0 false

Apply MP grease to the crank arm pivot of the windshield wiper motor assembly.


c.
E291225C01
0.615,0.281 0.854,0.521 false 2.219,0.25 2.75,0.156 false 0.396,0.198 0.708,0.354 0.313,0.156 10 false *1 2.792,0.073 3.104,0.229 0.313,0.156 10 false *2
*1 No. 1 Front Wiper Link Rod
*2 No. 2 Front Wiper Link Rod


Engage the No. 1 front wiper link rod on the crank arm pivot of the front wiper crank sub-assembly.


d.

Engage the No. 2 front wiper link rod on the crank arm pivot of the front wiper crank sub-assembly.


Hide 2.INSTALL WINDSHIELD WIPER MOTOR AND LINK

a.
E322472C01
2.469,3.073 2.792,2.729 true 1.083,2.875 0.885,2.698 true 2.26,3.021 2.573,3.177 0.313,0.156 10 false *1 1.177,2.813 1.49,2.969 0.313,0.156 10 false *1
*1 Grommet


Engage the grommet as shown in the illustration.


b.

Install the windshield wiper motor and link with the 2 bolts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


c.

Connect the connector.


Hide 55781E 3.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

a.

Engage the 9 guides as shown in the illustration.

E322469


b.

Engage the 7 claws to install the cowl top ventilator louver sub-assembly as shown in the illustration.

E324453


c.

Install the 2 clips.


d.

Connect the washer hose.


Hide 53383 4.INSTALL HOOD TO COWL TOP SEAL

a.

Engage the 7 clips to install the hood to cowl top seal.


Hide 53445 5.INSTALL HOOD HINGE COVER RH

a.
E324454

Engage the clip to install the hood hinge cover RH as indicated by the arrow shown in the illustration.


b.
E321993

Engage the 3 claws and guide.


Hide 53446 6.INSTALL HOOD HINGE COVER LH

HINT:

Use the same procedure as for the LH side.


Hide 85221B 7.INSTALL FRONT WIPER ARM AND BLADE LH

a.
E238922C01
1.698,1.219 2.594,0.875 true 1.979,3.479 2.75,3.344 true 0.635,4.135 0.635,3.531 true 2.625,0.781 3.083,1.208 0.458,0.427 10 *a 2.771,3.25 3.24,3.615 0.469,0.365 10 *b 0.531,4.188 0.948,4.563 0.417,0.375 10 *1
*1 Wire Brush
*a Wiper Arm Serration
*b Wiper Pivot Serration


When reinstalling:

NOTICE:

Do not grind the serrations excessively.


i.

Clean the wiper arm serrations to remove any burrs, dirt, etc.


ii.

Clean the wiper pivot serrations with a wire brush.



b.

Turn the ignition switch to ON.


c.

Operate the wiper switch and stop the windshield wiper motor assembly at the automatic stop (park) position.


d.

Turn the ignition switch off.


e.
E325063C02
1.771,1.208 2,1.229 false 1.594,1.125 1.906,1.281 0.313,0.156 10 false *a 2.333,0.76 2.646,0.917 0.313,0.156 10 false *b
*a Hood Hinge Cover Edge
*b 35.0 to 45.0 mm (1.377 to 1.771 in.)


Align the front wiper arm and blade LH as shown in the illustration.


f.

Install the front wiper arm and blade LH with the nut.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)

HINT:

Hold the wiper arm by hand while tightening the nut.



g.

Operate the front wipers while spraying washer fluid on the glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.


h.

Raise the wiper arm 2 times and check that the tip of the front wiper blade is at the position shown in the illustration.


Hide 85211B 8.INSTALL FRONT WIPER ARM AND BLADE RH

a.
E238922C03
1.698,1.219 2.594,0.875 true 1.979,3.479 2.75,3.344 true 0.635,4.135 0.635,3.531 true 2.625,0.781 3.083,1.208 0.458,0.427 10 *a 2.771,3.25 3.24,3.615 0.469,0.365 10 *b 0.531,4.188 0.948,4.563 0.417,0.375 10 *1
*1 Wire Brush
*2 Wiper Arm Serration
*3 Wiper Pivot Serration


When reinstalling:

NOTICE:

Do not grind the serrations excessively.


i.

Clean the wiper arm serrations to remove any burrs, dirt, etc.


ii.

Clean the wiper pivot serrations with a wire brush.



b.

Turn the ignition switch to ON.


c.

Operate the wiper switch and stop the windshield wiper motor assembly at the automatic stop (park) position.


d.

Turn the ignition switch off.


e.
E324968C02
1.573,1.24 1.917,0.938 true 1.385,1.198 1.698,1.354 0.313,0.156 10 false *a
*a Ceramic Dot


Align the front wiper arm and blade assembly RH as shown in the illustration.


f.

Install the front wiper arm and blade RH with the nut.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)

HINT:

Hold the wiper arm by hand while tightening the nut.



g.

Operate the front wipers while spraying washer fluid on the glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.


h.

Raise the wiper arm 2 times and check that the tip of the front wiper blade is at the position shown in the illustration.


Hide 85292B 9.INSTALL FRONT WIPER ARM HEAD CAP

a.

Engage the 3 claws to install the front wiper arm head cap.

HINT:

Use the same procedure for the other side.