Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT DIMMER SWITCH › from 2015.08
RM19Y0E _59 Vehicle Exterior _003020 LIGHTING (EXT) _0015287 HEADLIGHT DIMMER SWITCH G

LIGHTING (EXT)  HEADLIGHT DIMMER SWITCH  INSPECTION  


PROCEDURE

Hide 84140 1.INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY (for RHD)

a.
E333875C01
0.615,0.583 1.198,1.052 true 0.427,1.719 0.906,1.135 true 1.042,1.74 1.333,1.146 true 1.677,1.729 1.573,1.135 true 2.375,1.719 2.125,1.146 true 2.958,1.729 2.385,1.135 true 1.292,0.604 1.458,1.052 true 1.969,0.615 1.719,1.052 true 2.708,0.604 2.271,1.052 true 0.125,0.094 0.438,0.25 0.313,0.156 10 false *a 0.219,1.792 0.667,1.99 0.448,0.198 10 false TLR2 0.927,1.802 1.375,2 0.448,0.198 10 false TL1 1.542,1.802 1.99,2 0.448,0.198 10 false HL_T 2.198,1.802 2.646,2 0.448,0.198 10 false DIM HI 2.885,1.802 3.333,2 0.448,0.198 10 false T_E 0.479,0.365 0.927,0.563 0.448,0.198 10 false FFG 1.146,0.365 1.594,0.563 0.448,0.198 10 false HL_L 1.906,0.365 2.354,0.563 0.448,0.198 10 false TR1 2.531,0.365 3.156,0.563 0.625,0.198 10 false PASS
*a Component without harness connected
(Headlight Dimmer Switch Assembly)


Inspect the light control switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
5 (HL_L) - 6 (HL_T) - 12 (T_E) Light control switch off 10 kΩ or higher
6 (HL_T) - 12 (T_E) Light control switch tail Below 1 Ω
5 (HL_L) - 6 (HL_T) - 12 (T_E) Light control switch head




b.

Inspect the headlight dimmer switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
11 (PASS) - 12 (T_E) Headlight dimmer switch flash Below 1 Ω
10 (DIM HI) - 12(T_E) Headlight dimmer switch high beam


HINT:

Perform the flash and high beam inspection with the light control switch on head.




c.

Inspect the turn signal switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
7 (TR1) - 12 (T_E) Turn signal switch in right turn position Below 1 Ω
1 (TLR2) - 7 (TR1) - 12 (T_E) Turn signal switch in full right turn position Below 1 Ω
1 (TLR2) - 12 (T_E) Turn signal switch in neutral position 10 kΩ or higher
4 (TL1) - 12 (T_E)
7 (TR1) - 12 (T_E)
4 (TL1) - 12 (T_E) Turn signal switch in left turn position Below 1 Ω
1 (TLR2) - 4 (TL1) - 12 (T_E) Turn signal switch in full left turn position Below 1 Ω




d.

Inspect the fog light switch (w/ Front Fog Light).

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
3 (FFG) - 12 (T_E) Fog light switch off 10 kΩ or higher
3 (FFG) - 12 (T_E) Front fog light switch on Below 1 Ω


If the result is not as specified, replace the headlight dimmer switch assembly.



Hide 84140 2.INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY (for LHD)

a.
E333876C01
1.094,1.042 0.625,0.5 true 0.906,1.125 0.469,1.823 true 1.177,1.135 1.063,1.833 true 1.594,1.042 1.302,0.5 true 1.75,1.135 1.76,1.823 true 1.875,1.042 1.969,0.5 true 2.031,1.135 2.302,1.823 true 2.156,1.042 2.708,0.51 true 2.396,1.146 2.833,1.833 true 0.354,1.833 0.75,2 0.396,0.167 10 false T_E 0.854,1.833 1.438,2 0.583,0.167 10 false DIM HI 1.604,1.833 2.188,2 0.583,0.167 10 false HL_T 1.167,0.333 1.75,0.5 0.583,0.167 10 false TL1 2.688,1.833 3.188,2 0.5,0.167 10 false TLR2 0.458,0.333 1.042,0.5 0.583,0.167 10 false PASS 2.188,1.833 2.771,2 0.583,0.167 10 false TR1 1.813,0.333 2.396,0.5 0.583,0.167 10 false HL_L 2.583,0.333 3.167,0.5 0.583,0.167 10 false FFG 0.104,0.073 0.688,0.24 0.583,0.167 10 false *a
*a Component without harness connected
(Headlight Dimmer Switch Assembly)


Inspect the light control switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
8 (HL_L) - 7 (HL_T) - 1 (T_E) Light control switch off 10 kΩ or higher
7 (HL_T) - 1 (T_E) Light control switch tail Below 1 Ω
8 (HL_L) - 7 (HL_T) - 1 (T_E) Light control switch head




b.

Inspect the headlight dimmer switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
2 (PASS) - 1 (T_E) Headlight dimmer switch flash Below 1 Ω
3 (DIM HI) - 1 (T_E) Headlight dimmer switch high beam


HINT:

Perform the flash and high beam inspection with the light control switch on head.




c.

Inspect the turn signal switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
9 (TR1) - 1 (T_E) Turn signal switch in right turn position Below 1 Ω
12 (TLR2) - 9 (TR1) - 1 (T_E) Turn signal switch in full right turn position Below 1 Ω
12 (TLR2) - 1 (T_E) Turn signal switch in neutral position 10 kΩ or higher
6 (TL1) - 1 (T_E)
9 (TR1) - 1 (T_E)
6 (TL1) - 1 (T_E) Turn signal switch in left turn position Below 1 Ω
12 (TLR2) - 6 (TL1) - 1 (T_E) Turn signal switch in full left turn position Below 1 Ω




d.

Inspect the fog light switch (w/ Front Fog Light).

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
10 (FFG) - 1 (T_E) Fog light switch off 10 kΩ or higher
10 (FFG) - 1 (T_E) Front fog light switch on Below 1 Ω


If the result is not as specified, replace the headlight dimmer switch assembly.