Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) › from 2015.08
RM19Y0E _56 Audio / Visual / Telematics _003000 AUDIO / VIDEO _0015166 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Sound Signal Circuit between Radio Receiver and Stereo Jack Adapter  


DESCRIPTION

The No. 1 stereo jack adapter assembly sends and external device sound signal to the stereo component tuner assembly through this circuit.

If there is an open or short in the circuit, sound cannot be heard from the speakers even if there is no malfunction in the stereo component tuner assembly or speakers.

WIRING DIAGRAM

E324169E02
0.083,3.146 2.458,3.594 2.375,0.448 10 false Stereo Component Tuner Assembly 5.083,3.167 6.74,3.708 1.656,0.542 10 false No. 1 Stereo Jack Adapter Assembly 5.083,3 5.74,3.333 0.656,0.333 10 false E91 4.354,0.24 5.052,0.604 0.698,0.365 10 false (Shield) 2.438,0.24 3.135,0.604 0.698,0.365 10 false (Shield) 1.677,0.646 2.115,1.01 0.438,0.365 10 false E73 1.677,1.042 2.115,1.406 0.438,0.365 10 false E73 1.677,1.458 2.115,1.823 0.438,0.365 10 false E73 1.688,1.865 2.125,2.229 0.438,0.365 10 false E73 1.698,2.313 2.135,2.677 0.438,0.365 10 false E92 1.688,2.719 2.125,3.083 0.438,0.365 10 false E92 1.719,0.448 2.156,0.813 0.438,0.365 10 false 16 1.729,0.854 2.167,1.219 0.438,0.365 10 false 15 1.729,1.271 2.167,1.635 0.438,0.365 10 false 17 1.729,1.677 2.167,2.042 0.438,0.365 10 false 18 1.76,2.115 2.188,2.427 0.427,0.313 10 false 2 1.76,2.521 2.188,2.833 0.427,0.313 10 false 3 5.198,2.219 5.625,2.531 0.427,0.313 10 false 2 5.198,2.625 5.625,2.938 0.427,0.313 10 false 3 5.198,0.542 5.625,0.854 0.427,0.313 10 false 6 5.188,0.948 5.615,1.26 0.427,0.313 10 false 5 5.188,1.365 5.615,1.677 0.427,0.313 10 false 7 5.188,1.771 5.615,2.083 0.427,0.313 10 false 9 5.469,0.635 6.167,1 0.698,0.365 10 false ALO 5.469,1.042 6.167,1.406 0.698,0.365 10 false ARO 5.469,1.469 6.167,1.833 0.698,0.365 10 false ASGN 5.479,1.875 6.177,2.24 0.698,0.365 10 false AGND 5.469,2.323 6.167,2.688 0.698,0.365 10 false UDO- 5.479,2.719 6.177,3.083 0.698,0.365 10 false UDO+ 1.25,2.302 1.948,2.667 0.698,0.365 10 false UDI- 1.229,2.719 1.927,3.083 0.698,0.365 10 false UDI+ 1.146,0.635 1.844,1 0.698,0.365 10 false AGND 1.25,1.042 1.948,1.406 0.698,0.365 10 false ARO 1.25,1.469 1.948,1.833 0.698,0.365 10 false ALO 1.125,1.875 1.823,2.24 0.698,0.365 10 false ASGN

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT TUNER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.

Disconnect the E73 and E92 stereo component tuner assembly connectors.


b.

Disconnect the E91 No. 1 stereo jack adapter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
E73-15 (ARO) - E91-5 (ARO) Always Below 1 Ω
E73-16 (AGND) - E91-6 (ALO) Always Below 1 Ω
E73-17 (ALO) - E91-7 (ASGN) Always Below 1 Ω
E73-18 (ASGN) - E91-9 (AGND) Always Below 1 Ω
E92-2 (UDI-) - E91-2 (UDO-) Always Below 1 Ω
E92-3 (UDI+) - E91-3 (UDO+) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
E73-15 (ARO) or E91-5 (ARO) - Body ground Always 10 kΩ or higher
E73-16 (AGND) or E91-6 (ALO) - Body ground Always 10 kΩ or higher
E73-17 (ALO) or E91-7 (ASGN) - Body ground Always 10 kΩ or higher
E73-18 (ASGN) or E91-9 (AGND) - Body ground Always 10 kΩ or higher
E92-2 (UDI-) or E91-2 (UDO-) - Body ground Always 10 kΩ or higher
E92-3 (UDI+) or E91-3 (UDO+) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR