Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM › from 2015.08
RM19Y0E _58 Vehicle Interior _003012 SEAT BELT _0015223 SEAT BELT WARNING SYSTEM G

SEAT BELT  SEAT BELT WARNING SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 73210 1.INSPECT DRIVER SIDE SEAT BELT WARNING LIGHT

a.

Turn the ignition switch to ON.


b.

When the driver side seat belt is not fastened, check that the driver side seat belt warning light on the combination meter assembly blinks.


c.

Lift up the vehicle using a swing arm type lift.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS


d.

Start the engine.


e.

When the driver side seat belt is not fastened and the vehicle is driven at approximately 20 km/h (12 mph) or more, check that the driver side seat belt warning light on the combination meter assembly blinks at an interval of 1.2 seconds for 30 seconds.

After that, check that the driver side seat belt warning light on the combination meter assembly blinks at an interval of 0.4 seconds.


f.

When the driver side seat belt is fastened, check that the driver side seat belt warning light on the combination meter assembly is off.


Hide 73240 2.INSPECT FRONT PASSENGER SIDE SEAT BELT WARNING LIGHT

a.

Turn the ignition switch to ON.


b.

Place a weight of 20 kg (44.0 lb) on the front passenger side seat.

NOTICE:

Place the weight on the seat cushion and do not allow it to come into contact with the seatback.



c.

When the front passenger side seat belt is not fastened, check that the front passenger side seat belt warning light on the telltale light assembly blinks.


d.

Lift up the vehicle using a swing arm type lift.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS


e.

Start the engine.


f.

When the front passenger side seat is occupied, the front passenger side seat belt is not fastened and the vehicle is driven at approximately 20 km/h (12 mph) or more, check that the front passenger side seat belt warning light on the telltale light assembly blinks at an interval of 1.2 seconds for 30 seconds.

After that, check that the front passenger side seat belt warning light on the telltale light assembly blinks at an interval of 0.4 seconds.


g.

When the front passenger side seat belt is fastened, check that the front passenger side seat belt warning light on the telltale light assembly turns off.


Hide 83100 3.INSPECT SEAT BELT WARNING BUZZER

a.

Place a weight of 20 kg (44.0 lb) on the front passenger side seat.

NOTICE:

Place the weight on the seat cushion and do not allow it to come into contact with the seatback.



b.

Lift up the vehicle using a swing arm type lift.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS


c.

Start the engine.


d.

Check that the seat belt warning buzzer in the combination meter assembly sounds at an interval of 1.2 seconds for 30 seconds.


e.

After the seat belt warning buzzer has been sounding for 30 seconds at an interval of 1.2 seconds, check that the seat belt warning buzzer in the combination meter assembly sounds at an interval of 0.4 seconds for 90 seconds.


f.

Check that the seat belt warning buzzer in the combination meter assembly stops 2 minutes after it started sounding at an interval of 1.2 seconds.


g.

After the buzzer has stopped, turn the ignition switch off and then start the engine again. Drive the vehicle at approximately 20 km/h (12 mph) or more while the driver side or front passenger side seat belt is not fastened, and check that the buzzer sounds again.


h.

After the buzzer has stopped, fasten the driver side or front passenger side seat belt. Drive the vehicle at approximately 20 km/h (12 mph) or more and unfasten the driver side front passenger side seat belt, and check that the buzzer sounds again.


i.

After the buzzer has stopped, fasten the driver side or front passenger side seat belt. Drive the vehicle at approximately 20 km/h (12 mph) or more and unfasten the driver side or front passenger side seat belt, and check that the buzzer sounds again.


j.

After the buzzer has stopped, stop the vehicle, move the shift lever to R, and then move it to D. Drive the vehicle at approximately 20 km/h (12 mph) or more, and check that the buzzer sounds again.*1


k.

After the buzzer has stopped, stop the vehicle, select reverse gear and then select 1st gear. Drive the vehicle at approximately 20 km/h (12 mph) or more, and check that he buzzer sounds again.*2

*1: for Automatic Transmission

*2: for Manual Transmission