Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM › from 2015.08
RM19Y0E _59 Vehicle Exterior _003016 WINDOW / GLASS _0015247 POWER WINDOW CONTROL SYSTEM D

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  OPERATION CHECK  


CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (WINDOW LOCK SWITCH)


HINT:

Before performing the window lock switch operation check, make sure that the window lock switch is off (the switch is not pushed in).


a.
E324771

Check that the front passenger side and rear side windows cannot be operated when the window lock switch of the power window regulator master switch assembly is pushed in.

OK:

Front passenger side and rear side windows are disabled.



b.

Check that the front passenger side and rear side windows can be operated when the window lock switch is pressed again.

OK:

Front passenger side and rear side windows operate normally.




CHECK MANUAL UP/DOWN FUNCTION


a.

Check that the driver side power window operates as follows:

OK:
Condition Master Switch Switch Operation Power Window
Ignition switch ON Driver side Pulled halfway up UP (Closes)
Pulled halfway down DOWN (Opens)



b.

Check that the front passenger side power window and rear side power window operates as follows:

OK:
Condition Regulator Switch Switch Operation Power Window
·

Ignition switch ON

·

Window lock switch OFF


Front passenger side Pulled up UP (Closes)
Pushed down DOWN (Opens)
Rear LH side Pulled up UP (Closes)
Pushed down DOWN (Opens)
Rear RH side Pulled up UP (Closes)
Pushed down DOWN (Opens)




CHECK AUTO UP / DOWN FUNCTION


a.

Check that the driver side power window operates as follows:

OK:
Condition Master Switch Switch Operation Power Window
Ignition switch ON Driver side Fully pulled up AUTO UP (Closes)
Fully pushed down AUTO DOWN (fully opens)




CHECK REMOTE MANUAL UP/DOWN FUNCTION


a.

Check that the front passenger side power window and rear side power window operates as follows:

OK:
Condition Regulator Switch Switch Operation Power Window
·

Ignition switch ON

·

Window lock switch OFF


Front passenger side Pulled up UP (Closes)
Pushed down DOWN (Opens)
Rear LH side Pulled up UP (Closes)
Pushed down DOWN (Opens)
Rear RH side Pulled up UP (Closes)
Pushed down DOWN (Opens)




CHECK KEY-OFF OPERATION FUNCTION


a.

Check that each power window can be operated with the window regulator master switch assembly after the ignition switch is turned off.


b.

Check that all the power windows cannot be operated after more than approximately 43 seconds have elapsed since the ignition switch is turned off.



CHECK JAM PROTECTION FUNCTION (DRIVER SIDE DOOR POWER WINDOW)


a.

Check the basic function.

CAUTION:

Do not put your fingers between the door frame and door glass to check the jam protection function. Also, prevent any part of your body from being caught during inspection.


HINT:

The jam protection function is operative during both the auto up and manual up operations while the engine is running or the ignition switch is ON, and also within 43 seconds have elapsed after the ignition switch is turned off.


i.

Fully open the window.


ii.
E324770C01
1.656,0.667 2.5,0.417 true 1.417,0.583 1.917,0.25 true 2.521,0.333 2.833,0.49 0.313,0.156 10 false *1 1.917,0.167 2.229,0.323 0.313,0.156 10 false *2
*1 Thick Book
*2 Piece of Cloth


Set a thick book wrapped with a piece of cloth near the window fully closed position.


iii.

Operate the auto up or manual up function to check that the power window goes down after the book is caught between the window and door frame, and stops when the opening reaches approximately 200 mm (7.87 in.).

HINT:

The power window moves down approximately 50 mm (1.97 in.). However, when the opening does not reach 200 mm (7.87 in.), the power window continues to go down until the opening reaches 200 mm (7.87 in.) or until approximately 5 seconds elapse.



iv.

While the power window is moving down, check that the door glass cannot be raised when the power window regulator switch is used.




CHECK PTC OPERATION


HINT:

PTC operation is a function that prevents overloading of the power window regulator by stopping the motor. PTC operation activates when the power window regulator switch assembly is operated for a predetermined amount of time.


a.

Pull up and hold the power window regulator switch assembly for more than 90 seconds. Then release the switch.


b.

Check that pressing the switch does not move the window.


c.

Wait until 60 seconds have passed since the switch was released in the first step. Check that pressing the switch results in normal window movement.