Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM › from 2015.08
RM19Y0E _59 Vehicle Exterior _003016 WINDOW / GLASS _0015247 POWER WINDOW CONTROL SYSTEM J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  Power Windows do not Operate at All  


DESCRIPTION

If all of the power windows do not operate, the power window regulator master switch assembly may have no power or may be malfunctioning.

WIRING DIAGRAM

B424481E01
4.906,2.073 6.896,2.76 1.99,0.688 10 false Power Window Regulator Master Switch Assembly 4.927,1.885 6.917,2.573 1.99,0.688 10 false F9*1 5.323,1.885 7.156,2.583 1.833,0.698 10 false G9*2 5.333,1.115 7.156,1.802 1.823,0.688 10 false E 5.333,0.563 7.156,1.25 1.823,0.688 10 false IG 5.094,1.125 6.917,1.813 1.823,0.688 10 false 3 4.927,0.563 6.75,1.25 1.823,0.688 10 false 10*2 4.927,0.333 6.75,1.021 1.823,0.688 10 false 16*1 2.427,0.896 4.25,1.583 1.823,0.688 10 false POWER 0.583,0.667 2.406,1.354 1.823,0.688 10 false from IG POWER Relay 0.25,2.417 1.083,2.792 0.833,0.375 10 false *1: for RHD 1.094,2.417 2.917,2.792 1.823,0.375 10 false *2: for LHD

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - POWER SOURCE)
a.
B396099C02
1.073,0.177 1.49,0.427 0.417,0.25 1.917,0.167 2.333,0.417 0.417,0.25 2.563,1.365 2.979,1.365 true 0.167,0.167 0.938,0.667 0.771,0.5 10 false *a 1.198,0.229 1.885,0.75 0.688,0.521 10 false F9 3.031,1.292 3.427,1.844 0.396,0.552 10 false IG 2.042,0.219 2.74,0.74 0.698,0.521 10 false G9 0.865,0.219 1.635,0.719 0.771,0.5 10 false *A 1.708,0.208 2.479,0.708 0.771,0.5 10 false *B
*A for RHD
*B for LHD
*a Front view of wire harness connector
(to Power Window Regulator Master Switch Assembly)


Disconnect the F9*1 or G9*2 power window regulator master switch assembly connector.

*1: for RHD

*2: for LHD



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RHD
Tester Connection Switch Condition Specified Condition
F9-16 (IG) - Body ground Ignition switch ON 11 to 14 V

for LHD
Tester Connection Switch Condition Specified Condition
G9-10 (IG) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG




OK

2.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - BODY GROUND)
a.

Disconnect the F9*1 or G9*1 power window regulator master switch assembly connector.

*1: for RHD

*2: for LHD



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
F9-3 (E) - Body ground Always Below 1 Ω

for LHD
Tester Connection Condition Specified Condition
G9-3 (E) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG




OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR