Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2015.08
RM19Y0E _58 Vehicle Interior _003010 SUPPLEMENTAL RESTRAINT SYSTEMS _0015213 AIRBAG SYSTEM D

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  DIAGNOSIS SYSTEM  


SYMPTOM SIMULATION


C206435C01
1.552,0.406 1.958,0.656 0.406,0.25 10 false *a 1.177,2.75 1.521,2.948 0.344,0.198 10 false *b 1.594,4.24 1.917,4.427 0.323,0.188 10 false *c
*a Vibrate Slightly
*b Shake Slightly
*c Vibrate Slightly


HINT:

The most difficult case in troubleshooting is when no problem symptoms occur. In such a case, a thorough problem analysis must be carried out. A simulation of the same or similar conditions and environment in which the problem occurred in the customer's vehicle should be carried out. No matter how much skill or experience a technician has, troubleshooting without confirming the problem symptoms will lead to important repairs being overlooked and mistakes or delays.


a.

Vibration method: When vibration seems to be the major cause.

HINT:

Perform the simulation method only during the primary check period (for approximately 6 seconds after the ignition switch is turned to ON).


i.

Slightly vibrate the part of the sensor considered to be the cause of the problem with your fingers and check whether the malfunction occurs.

NOTICE:

Shaking the relays too strongly may result in open relays.



ii.

Slightly shake the connector vertically and horizontally.


iii.

Slightly shake the wire harness vertically and horizontally.

HINT:

The connector joint and fulcrum of the vibration are the major areas to be checked thoroughly.





FUNCTION OF SRS WARNING LIGHT


a.

Primary check.

i.

Turn the ignition switch off. Wait for at least 2 seconds, and then turn the ignition switch to ON. The SRS warning light comes on for approximately 6 seconds and diagnosis of the airbag system is performed.

HINT:

If trouble is detected during the primary check, the SRS warning light remains on even after the primary check period (approximately 6 seconds) has elapsed.




b.

Constant check.

i.

After the primary check, the airbag ECU assembly constantly monitors the airbag system for trouble.

HINT:

If trouble is detected during the constant check, the airbag ECU assembly functions as follows:

·

The SRS warning light comes on.

·

The SRS warning light goes off, and then comes on. This blinking pattern indicates a source voltage drop. The SRS warning light goes off 5 seconds after the source voltage returns to normal.





c.

Review.

i.

When the airbag system is normal:

The SRS warning light comes on only during the primary check period (for approximately 6 seconds after the ignition switch is turned to ON).


ii.

When the airbag system has trouble:

·

The SRS warning light remains on even after the primary check period has elapsed.

·

The SRS warning light goes off after the primary check, but comes on again during the constant check.

·

The SRS warning light does not come on when turning the ignition switch from off to ON.


HINT:

The airbag ECU assembly functions to keep the SRS warning blinking if the airbag has been deployed.





CHECK SRS WARNING LIGHT


a.

Turn the ignition switch to ON and check that the SRS warning light comes on for approximately 6 seconds (primary check).


b.

Check that the SRS warning light goes off approximately 6 seconds after the ignition switch is turned to ON (constant check).

HINT:

When any of the following symptoms occur, refer to the "Problem Symptoms Table".

·

The SRS warning light comes on occasionally after the primary check period has elapsed.

·

The SRS warning light comes on, but a DTC is not output.

·

The ignition switch is turned from off to ON, but the SRS warning light does not come on.


Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PROBLEM SYMPTOMS TABLE




FUNCTION OF SRS CONNECTORS


a.

SRS connectors are located as shown in the illustration.

C312961E01
5.188,0.51 6.781,1.01 1.594,0.5 10 false Airbag ECU Assembly 0.469,2.042 3.156,2.646 2.688,0.604 10 false Front Seat Outer Belt Assembly RH (Front Pretensioner Squib RH) 0.458,3.031 3.146,3.635 2.688,0.604 10 false Front Seat Outer Belt Assembly LH (Front Pretensioner Squib LH) 0.458,4.01 2.625,4.635 2.167,0.625 10 false Horn Button Assembly (Driver Side Squib) 4.021,4.042 5.177,4.594 1.156,0.552 10 false Spiral Cable Sub-assembly 0.323,5 3.167,5.625 2.844,0.625 10 false Instrument Panel Passenger Airbag Assembly (Front Passenger Side Squib) 0.729,6.125 2.375,6.677 1.646,0.552 10 false Front Airbag Sensor RH 0.708,7.198 2.354,7.75 1.646,0.552 10 false Front Airbag Sensor LH 5.115,1.073 5.271,1.271 0.156,0.198 10 false 1 5.135,1.26 5.292,1.458 0.156,0.198 10 false 2 6.417,1.073 6.573,1.271 0.156,0.198 10 false 3 6.427,1.26 6.583,1.458 0.156,0.198 10 false 4 3.26,1.854 3.49,2.063 0.229,0.208 10 false 16 3.5,2.375 3.729,2.583 0.229,0.208 10 false 15 3.229,2.844 3.458,3.052 0.229,0.208 10 false 16 3.51,3.396 3.74,3.604 0.229,0.208 10 false 15 2.771,3.865 3,4.073 0.229,0.208 10 false 8 3.031,4.385 3.26,4.594 0.229,0.208 10 false 7 5.229,3.854 5.458,4.063 0.229,0.208 10 false 6 5.51,4.365 5.74,4.573 0.229,0.208 10 false 5 3.229,4.844 3.458,5.052 0.229,0.208 10 false 10 3.542,5.375 3.771,5.583 0.229,0.208 10 false 9 2.75,5.844 2.979,6.052 0.229,0.208 10 false 14 3.021,6.365 3.25,6.573 0.229,0.208 10 false 13 2.74,6.833 2.969,7.042 0.229,0.208 10 false 14 3.021,7.365 3.25,7.573 0.229,0.208 10 false 13 4.385,6.125 4.615,6.333 0.229,0.208 10 false 12 4.802,6.125 5.031,6.333 0.229,0.208 10 false 11 4.813,7.135 5.042,7.344 0.229,0.208 10 false 11 4.375,7.135 4.604,7.344 0.229,0.208 10 false 12

Connector Type Application
Terminal Twin-Lock Mechanism Connectors 5, 9, 11, 12
Half Connection Prevention Mechanism Connectors 5, 9, 11, 12
Activation Prevention Mechanism Connectors 2, 4, 6, 8, 10, 16
Connector Lock Mechanism Connectors 7, 15
Connector Position Assurance Mechanism Connector 13


b.

Terminal twin-lock mechanism

C234183E13
1.771,0.896 2.115,0.125 2.115,0.125 1.708,0.125 true 5.792,0.615 5.719,0.229 5.719,0.229 5.469,0.229 false 0.385,0.052 1.833,0.281 1.448,0.229 10 false Lance (Primary Lock) 1.229,1.479 2.052,1.656 0.823,0.177 10 false Primary Lock 3.865,0.115 5.448,0.292 1.583,0.177 10 false Spacer (Secondary Lock) 4.885,1.479 5.896,1.656 1.01,0.177 10 false Secondary Lock

i.

This mechanism is designed to increase the ability of the terminal to remain connected and prevent it from accidentally being disconnected.


ii.

The connector has a two-piece construction consisting of the housing and spacer to securely lock the terminal using both the lance (primary lock) and spacer (secondary lock).



c.

Half connection prevention mechanism

C147461E12
1.542,1.406 1.458,1.135 1.458,1.135 1.313,1.135 false 1.823,1.354 1.729,0.833 1.729,0.833 1.531,0.833 false 2.365,1.323 2.229,0.583 2.229,0.583 2.021,0.583 true 3,1.177 3.229,0.594 3.229,0.594 3.396,0.594 false 3.25,1.302 3.385,0.896 3.385,0.896 3.583,0.896 true 6.094,1.135 5.938,0.771 5.938,0.771 5.74,0.771 true 1.167,0.479 2.052,0.698 0.885,0.219 10 Locking Arm 0.979,0.74 1.573,0.958 0.594,0.219 10 Stopper 0.469,1.042 1.333,1.26 0.865,0.219 10 Locking Part 3.469,0.5 3.906,0.688 0.438,0.188 10 Slider 3.667,0.802 4.156,1.031 0.49,0.229 10 Spring 5.177,0.677 5.76,0.865 0.583,0.188 10 Stopper 4.708,1.969 6.042,2.156 1.333,0.188 10 Rebound by Slider

i.

This mechanism is designed to prevent the connector from being connected only halfway.


ii.

If the connector is not completely connected, the connector is disconnected by the force of the spring so that no continuity exists.



d.

Activation prevention mechanism

C144513E02
2.042,0.74 2.417,0.417 true 1.833,1.958 2.302,2.417 true 2.354,1.052 2.448,1.198 false 1.396,0.802 0.802,0.375 false 5.51,0.917 5.833,1.208 true 5.771,2.021 6.083,2.115 true 5.094,1.979 5.292,2.417 true 1.51,2.083 1.615,2.302 1.615,2.302 1.677,2.125 false 1.583,1.823 1.604,1.479 1.604,1.479 1.667,1.823 true 0.948,0.042 3.073,0.313 2.125,0.271 10 When Connector is Connected 4.49,0.052 6.917,0.302 2.427,0.25 10 When Connector is Disconnected 2.458,0.333 3.979,0.542 1.521,0.208 10 Short Spring Plate 0.26,0.26 0.917,0.479 0.656,0.219 10 Housing 2.271,1.177 2.927,1.396 0.656,0.219 10 Housing 1.333,1.292 2.063,1.479 0.729,0.188 10 Terminal 1.292,2.323 2.125,2.531 0.833,0.208 10 Connectors 2.167,2.469 3.688,2.677 1.521,0.208 10 Short Spring Plate 2.281,1.521 2.708,1.677 0.427,0.156 10 Squib 5.656,1.521 6.042,1.677 0.385,0.156 10 Squib 5.438,1.208 7.156,1.438 1.719,0.229 10 Contacting Male Terminal 4.615,2.427 6.167,2.635 1.552,0.208 10 Short Spring Plate ON 6.135,2.042 7.094,2.292 0.958,0.25 10 Closed Circuit

i.

The activation prevention mechanism is designed to create a short circuit automatically between the positive (+) and negative (-) terminals of an airbag power source connector when disconnected.


ii.

The short spring plate contained in the connector creates a closed circuit on the airbag side (no potential difference can occur between both terminals), preventing accidental airbag deployment when servicing.



e.

Connector lock mechanism

C147462E22
2.51,0.344 2.01,0.219 false 2.615,0.781 2.26,0.906 true 2.448,1.25 2.25,1.333 false 4.938,0.896 5.24,0.708 false 0.927,0.073 1.979,0.5 1.052,0.427 10 false Lock the airbag connector lock 1.906,0.833 2.281,1 0.375,0.167 10 false Claw 1.792,1.26 2.281,1.427 0.49,0.167 10 false Groove 5.292,0.49 6.813,1.417 1.521,0.927 10 false Claw on the e airbag connector lock is locked in the groove

i.

This mechanism is designed to prevent the connector from accidentally being disconnected.


ii.

Locking the connector lock engages the e airbag connector lock claw in the groove of the other connector to connect the connector securely.



f.

Connector Position Assurance (CPA) mechanism

C161464E08
0.531,1.823 0.729,2.292 0.729,2.292 0.927,2.292 true 0.833,1.146 0.833,0.219 0.833,0.219 0.958,0.219 true 0.938,1.229 1.052,0.49 1.052,0.49 1.208,0.49 true 5.49,0.792 5.635,0.792 5.635,0.792 5.646,1.115 true 1.063,0.125 2.302,0.365 1.24,0.24 10 Female Connector 1.26,0.406 2.208,0.646 0.948,0.24 10 Locking Part 1,2.219 2.063,2.396 1.063,0.177 10 Male Connector 2.958,0.302 4.542,0.458 1.583,0.156 10 Primary Lock Completed 5.073,0.302 6.844,0.458 1.771,0.156 10 Secondary Lock Completed 4.896,0.698 5.521,0.875 0.625,0.177 10 Retainer

i.

This mechanism is designed to detect when the connector is connected only halfway.


ii.

The CPA and female connector slide to the male connector side at the same time and the primary lock is completed when the female connector is engaged with the male connector. From this point, only the CPA slides to the male connector side. The secondary lock is completed when the CPA retainer is engaged with the female connector. When the CPA and female connector ends are aligned, the connectors are completely engaged.




ACTIVATION PREVENTION MECHANISM


a.

Function of activation prevention mechanism

i.

An activation prevention mechanism is built into the connector (on the airbag ECU assembly side) of the airbag system squib circuit to prevent accidental airbag activation.


ii.

This mechanism closes the circuit when the connector is disconnected by bringing the short spring into contact with the terminals and insulating the circuit from external power sources to prevent accidental airbag activation.



b.

Releasing of activation prevention mechanism

i.

To release the activation prevention mechanism, insert a piece of paper with the same thickness as the male terminal (approximately 0.5 mm [0.0197 in.]) between the terminals and short spring to break the connection.


ii.

Refer to the following illustrations concerning connectors utilizing the activation prevention mechanism and its release method.

CAUTION:

Never release the activation prevention mechanism on the squib connector even when inspecting with the squib disconnected.


NOTICE:
·

Do not release the activation prevention mechanism unless specially directed by the troubleshooting procedure.

·

To prevent the terminal and short spring from being damaged, always use a piece of paper with the same thickness as the male terminal.



C312963E01
2.052,1.594 2.271,1.99 2.271,1.99 2.51,1.615 true 2.208,1.604 2.271,1.979 2.271,1.979 2.365,1.594 true 4.49,1.531 4.573,1.896 4.573,1.896 4.646,1.521 true 4.365,1.51 4.573,1.896 4.573,1.896 4.771,1.521 true 3.115,3.146 3.219,2.802 3.219,2.802 3.375,2.802 false 2.729,3.198 2.99,3.677 2.99,3.677 3.208,3.677 true 5.292,3.177 5.5,2.771 5.5,2.771 5.667,2.771 false 5.073,3.208 5.5,3.656 5.5,3.656 5.781,3.656 true 2.458,5.542 2.5,5.958 2.5,5.958 2.573,5.552 true 3.542,4.969 3.76,4.969 3.76,4.969 3.958,5.365 true 4.76,5.427 4.844,5.042 4.844,5.042 4.99,5.042 false 6.115,4.938 5.938,4.938 5.938,4.938 5.792,5.396 true 1.885,0.292 2.729,0.5 0.844,0.208 10 false Connector 2 4.458,0.302 5.302,0.51 0.844,0.208 10 false Connector 4 1.865,2.042 2.708,2.25 0.844,0.208 10 false Short Spring 4.198,2 5.042,2.208 0.844,0.208 10 false Short Spring 3.438,2.729 4,2.958 0.563,0.229 10 false Paper 3.302,3.615 4.208,3.833 0.906,0.219 10 false Short Spring 1.979,3.938 3.323,4.229 1.344,0.292 10 false Before Release 5.729,2.698 6.292,2.927 0.563,0.229 10 false Paper 5.865,3.573 6.771,3.792 0.906,0.219 10 false Short Spring 4.375,3.938 5.719,4.229 1.344,0.292 10 false After Release 2.115,6.042 2.958,6.25 0.844,0.208 10 false Short Spring 2.708,4.875 3.615,5.094 0.906,0.219 10 false Short Spring 5.073,4.958 5.635,5.188 0.563,0.229 10 false Paper 6.177,4.865 7.083,5.083 0.906,0.219 10 false Short Spring 3.76,6.073 5.104,6.365 1.344,0.292 10 false Before Release 5.625,6.083 6.969,6.375 1.344,0.292 10 false After Release 0.479,5.375 1.323,5.583 0.844,0.208 10 false Connector 6