Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM › from 2015.08
RM19Y0E _58 Vehicle Interior _003006 THEFT DETERRENT / KEYLESS ENTRY _0015192 ENGINE IMMOBILISER SYSTEM U

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  TERMINALS OF ECU  


CHECK TRANSPONDER KEY COIL


a.

Measure the voltage and check for pulses according to the value(s) in the table below.

B393753N02
3.333,0.083 3.75,0.333 0.417,0.25 3.417,0.135 3.979,0.417 0.563,0.281 10 false E80

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
E80-1 (COL+) - E80-5 (COL-) Input/Output G - W Key code communication No key in ignition key cylinder → Key inserted in ignition key cylinder Below 1 V → Pulse generation (See waveform) → Below 1 V -


b.

Inspect using an oscilloscope.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
B366383N01
2.969,0.979 3.365,1.292 0.396,0.313 10 false GND

Waveform (Reference)

Measurement Condition:
Item Content
Tester Connection E80-1 (COL+) - E80-5 (COL-)
Tool Setting 5 V/DIV., 200 ms./DIV.
Condition No key in ignition key cylinder → Key inserted in ignition key cylinder





CHECK TRANSPONDER KEY ECU ASSEMBLY


a.

Disconnect the E58 transponder key ECU assembly connector.

B393754N02
3.417,0.406 3.833,0.656 0.417,0.25 3.5,0.458 3.969,0.75 0.469,0.292 10 false E58


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
E58-1 (+B) - E58-14 (E) Input GR - W-B Battery power supply Always 11 to 14 V +B
E58-2 (IG) - E58-14 (E) Input Y - W-B Ignition switch power supply Ignition switch off → ON Below 1 V → 11 to 14 V IG SW
E58-4 (KSW) - Body ground Input R - Body ground Unlock warning switch No key in ignition key cylinder → Key inserted in ignition key cylinder Below 1 V → 11 to 14 V KEY SW(KSW) / B2780/15
E58-14 (E) - Body ground - W-B - Body ground Ground Always Below 1 Ω -

If the result is not as specified, there may be a malfunction on the wire harness side.



c.

Reconnect the E58 transponder key ECU assembly connector.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
E58-5 (COL+) - E58-16 (COL-) Input/Output G - W Key code communication No key in ignition key cylinder → Key inserted in ignition key cylinder Below 1 V → Pulse generation (See waveform 1) → Below 1 V -
E58-9 (SIO2) - E58-14 (E) Input/Output P - W-B Immobiliser communication Ignition switch off → ON Below 1 V → Pulse generation (See waveform 2) -
E58-10 (SIO) - E58-14 (E) Input/Output V-R - W-B Diagnosis tester communication Always 11 to 14 V -
E58-12 (IND) - E58-14 (E) Output V - W-B Security indicator light signal No key in ignition key cylinder Pulse generation (See waveform 3) -
E58-13 (T) - E58-14 (E) Input BR - W-B Terminal T of DLC3 DLC3 terminals 13 (ECUT) - 4 (E) connected 11 to 14 V -

If the result is not as specified, the ECU may have a malfunction.



e.

Inspect using an oscilloscope.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
B366383N01
2.969,0.979 3.365,1.292 0.396,0.313 10 false GND

Waveform 1 (Reference)

Measurement Condition:
Item Content
Tester Connection E58-5 (COL+) - E58-16 (COL-)
Tool Setting 5 V/DIV., 200 ms./DIV.
Condition No key in ignition key cylinder → Key inserted in ignition key cylinder



ii.
B426229N01
2.969,0.969 3.406,1.396 0.438,0.427 10 false GND

Waveform 2 (Reference)

Measurement Condition:
Item Content
Tester Connection E58-9 (SIO2) - E58-14 (E)
Tool Setting 5 V/DIV., 200 ms./DIV.
Condition Ignition switch off → ON



iii.
B366385E01
2.969,0.969 3.417,1.229 0.448,0.26 10 false GND

Waveform 3 (Reference)

Measurement Condition:
Item Content
Tester Connection E58-12 (IND) - E58-14 (E)
Tool Setting 5 V/DIV., 500 ms./DIV.
Condition No key in ignition key cylinder





CHECK ECM


A348484N06
2.01,0.625 2.427,0.875 0.417,0.25 4.365,0.625 4.781,0.875 0.417,0.25 2.104,0.677 2.688,0.969 0.583,0.292 10 false A24 4.448,0.677 5.031,0.969 0.583,0.292 10 false C50

a.

Measure the resistance and voltage, and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
A24-1 (+B1) - C50-4 (E01) Input G - W-B Power source of ECM Ignition switch ON 11 to 14 V -
C50-4 (E01) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
A24-13 (BAT) - C50-4 (E01) Input G - W-B Battery (for measuring battery voltage and for ECM memory) Always 11 to 14 V -
A24-54 (SIO2) - C50-4 (E01) Input/Output P - W-B Transponder key ECU communication Ignition switch off → ON Below 1 V → Pulse generation (See waveform) -

If the result is not as specified, the ECM may have a malfunction.


i.
B426229N01
2.969,0.969 3.406,1.396 0.438,0.427 10 false GND

Waveform (Reference)

Measurement Condition:
Item Content
Tester Connection A24-54 (SIO2) - C50-4 (E01)
Tool Setting 5 V/DIV., 200 ms./DIV.
Condition Ignition switch off → ON