Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM › from 2015.08
RM19Y0E _58 Vehicle Interior _003006 THEFT DETERRENT / KEYLESS ENTRY _0015192 ENGINE IMMOBILISER SYSTEM D

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  DTC CHECK / CLEAR  


CHECK DTC (Using GTS or Techstream)


a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream ON.


d.

Enter the following menus: Body Electrical / IMB / Trouble Codes.

Body Electrical > IMB > Trouble Codes
50001 586

e.

Check for DTCs.



CHECK DTC (Not using GTS or Techstream)


a.
H102540C05
1.833,0.385 1.75,0.385 1.75,0.385 1.583,0.896 true 1.771,1.469 1.938,1.938 1.938,1.938 2.021,1.938 true 0.135,0.115 0.573,0.521 0.438,0.406 10 false *1 1.906,0.313 2.229,0.604 0.323,0.292 10 false E 2.115,1.854 2.771,2.177 0.656,0.323 10 false ECUT
*1 DLC3


Turn the ignition switch to ON.


b.

Using SST, connect terminals 13 (ECUT) and 4 (E) of the DLC3.

SST
09843-18040  


c.

Read DTCs by observing the MIL. If any DTC is not detected, the MIL blinks as shown in the illustration.

B298663C01
5.938,2.229 6.802,2.844 0.865,0.615 10 3 sec. 0.365,0.667 0.833,1.063 0.469,0.396 10 ON 0.292,1.427 0.865,1.802 0.573,0.375 10 OFF 0.365,2.677 0.885,3.031 0.521,0.354 10 ON 0.292,3.427 0.917,3.792 0.625,0.365 10 OFF 0.917,0.354 1.583,0.667 0.667,0.313 10 3 sec. 0.875,2.417 1.542,2.729 0.667,0.313 10 3 sec. 2.24,2.208 3.021,2.615 0.781,0.406 10 1.5 sec. 3.083,2.208 4.073,2.646 0.99,0.438 10 2.5 sec. 1.271,0.083 2.177,0.417 0.906,0.333 10 0.25 sec. 1.365,2.208 2.125,2.573 0.76,0.365 10 0.5 sec. 1.604,3.813 2.125,4.094 0.521,0.281 10 0.5 sec. 3.104,4.458 3.563,4.76 0.458,0.302 10 *e 1.396,1.75 2.229,2.146 0.833,0.396 10 0.25 sec. 0.146,2.125 0.677,2.469 0.531,0.344 10 *b 0.146,0.073 0.563,0.448 0.417,0.375 10 *a 2.167,4.198 2.594,4.49 0.427,0.292 10 *c 4.615,4.198 5.031,4.49 0.417,0.292 10 *d
*a Normal System Code *b Trouble Code (Example Codes 21 and 31)
*c DTC 21 *d DTC 31
*e One Cycle - -


i.

DTCs 21 and 31 are detected and the MIL starts displaying the DTCs, as shown in the illustration. The MIL blinking pattern of DTC 21 will be displayed first.


ii.

A 2.5 seconds pause will occur. This pause will occur between the MIL blinking patterns of each DTC.


iii.

The MIL blinking pattern of DTC 31 will be displayed.


iv.

A 3.0 seconds pause will occur. This pause will occur when the MIL blinking pattern is the last of a string of multiple DTCs.


v.

The MIL will repeat the display of the string of DTCs.



d.

Check the details of the malfunction using the DTC chart.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DIAGNOSTIC TROUBLE CODE CHART


e.

After completing the check, disconnect terminals 13 (ECUT) and 4 (E) and turn off the display.

HINT:

In the event that 2 or more DTCs are detected, the MIL will indicate the smaller number DTC first.





CLEAR DTC (Using GTS or Techstream)


a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch ON.


c.

Turn the GTS or Techstream ON.


d.

Enter the following menus: Body Electrical / IMB / Trouble Codes.

Body Electrical > IMB > Clear DTCs
50002 586


CLEAR DTC (Not using GTS or Techstream)


a.

Remove the EFI fuse from the engine room relay block for more than 60 seconds, or disconnect the negative battery cable for more than 60 seconds. When disconnecting the negative battery cable, perform the "INITIALIZE" procedure.