Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM › from 2015.08
RM19Y0E _58 Vehicle Interior _003006 THEFT DETERRENT / KEYLESS ENTRY _0015192 ENGINE IMMOBILISER SYSTEM U

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the GTS or Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Body Electrical / IMB / Data List.


e.

According to the display on the GTS or Techstream, read the Data List.

Body Electrical > IMB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
TEST terminal DLC3 ECUT terminal status GND or OPEN GND: DLC3 ECUT terminal and E terminal connected
OPEN: DLC3 ECUT terminal and E terminal not connected
-
IG Ignition switch signal ON or OFF ON: Ignition switch ON
OFF: Ignition switch ACC or off
-
KEY SW(KSW) Key switch signal ON or OFF ON: Key inserted in ignition key cylinder
OFF: No key in ignition key cylinder
-
REQ permission signal Request permission signal status Output or Stop Output: Request permission signal output
Stop: Request permission signal stopped
-
Transponder commu. Result of transponder communication Accord or Discord Accord: Key code matches code registered in transponder key ECU assembly
Discord: Key code does not match code registered in transponder key ECU assembly
-
Immobilizer condition Immobiliser system status determined by transponder key ECU assembly UNSET or SET UNSET: Immobiliser unset (engine start permitted [key inserted in ignition key cylinder])
SET: Immobiliser set (engine start prohibited [no key in ignition key cylinder])
-
KEY8 Registration status of No. 8 key N.Reg, Master, Sub, Supp. Mst, Supp. sub or Unknown N.Reg: Not registered
Sub: Sub key registered
Supp. Mst: Additional master key registered
Supp. sub: Additional sub key registered
Unknown: Unknown
-
KEY7 Registration status of No. 7 key N.Reg, Master, Sub, Supp. Mst, Supp. sub or Unknown N.Reg: Not registered
Sub: Sub key registered
Supp. Mst: Additional master key registered
Supp. sub: Additional sub key registered
Unknown: Unknown
-
KEY6 Registration status of No. 6 key N.Reg, Master, Sub, Supp. Mst, Supp. sub or Unknown N.Reg: Not registered
Sub: Sub key registered
Supp. Mst: Additional master key registered
Supp. sub: Additional sub key registered
Unknown: Unknown
-
KEY5 Registration status of No. 5 key N.Reg, Master, Sub, Supp. Mst, Supp. sub or Unknown N.Reg: Not registered
Sub: Sub key registered
Supp. Mst: Additional master key registered
Supp. sub: Additional sub key registered
Unknown: Unknown
-
KEY4 Registration status of No. 4 key N.Reg, Master, Sub, Supp. Mst, Supp. sub or Unknown N.Reg: Not registered
Sub: Sub key registered
Supp. Mst: Additional master key registered
Supp. sub: Additional sub key registered
Unknown: Unknown
-
KEY3 Registration status of No. 3 key N.Reg, Master, Sub, Supp. Mst, Supp. sub or Unknown N.Reg: Not registered
Sub: Sub key registered
Supp. Mst: Additional master key registered
Supp. sub: Additional sub key registered
Unknown: Unknown
-
KEY2 Registration status of No. 2 key N.Reg, Master, Sub, Supp. Mst, Supp. sub or Unknown N.Reg: Not registered
Sub: Sub key registered
Supp. Mst: Additional master key registered
Supp. sub: Additional sub key registered
Unknown: Unknown
-
KEY1 Registration status of No. 1 key N.Reg, Master, Sub, Supp. Mst, Supp. sub or Unknown N.Reg: Not registered
Sub: Sub key registered
Supp. Mst: Additional master key registered
Supp. sub: Additional sub key registered
Unknown: Unknown
-
+B +B judgment ON or OFF(OPEN) ON: Battery power supply normal
OFF: Battery power supply malfunctioning
-
Mode Key code registration mode status Reg mode or Usual Reg mode: During key code registration mode
Usual: Not during key code registration mode
-
Manual register. Whether manual key code registration is possible or not Possible or Impossible Possible: Manual key code registration possible
Impossible: Manual key code registration impossible
-
EFI communication Result of SFI communication Accord or Discord Accord: SFI communication code confirmed
Discord: SFI communication code not confirmed
-
Transponder commu. mode Specification of transponder communication mode Unknown, DMC spec or TMC spec Unknown: Specification unknown
DMC spec: Transponder communication mode for DMC
TMC spec: Transponder communication mode for TMC
-
EFI commu. mode Specification of SFI communication mode Unknown, old spec or new spec Unknown: Specification unknown
old spec: Old specification SFI communication mode
new spec: New specification SFI communication mode
-
Incompleting frequen.(Manual) Number of times of manual key code registration forced termination Min.: 0, Max.: 15 Number of times manual key code registration forced termination performed -
Incompleting frequen.(Tool) Number of times of tool key code registration forced termination Min.: 0, Max.: 15 Number of times tool key code registration forced termination performed -
Add. reg. frequen.(Manual) Number of times of manual key code additional registration Min.: 0, Max.: 15 Number of times manual key code additional registration performed -
Add. reg. frequen.(Tool) Number of times of tool key code additional registration Min.: 0, Max.: 15 Number of times tool key code additional registration performed -
Key erased frequen.(Manual) Number of times of manual key code erasure Min.: 0, Max.: 15 Number of times manual key code erasure performed -
Key erased frequen.(Tool) Number of times of tool key code erasure Min.: 0, Max.: 15 Number of times tool key code erasure performed -
Diag. code number Number of DTCs Min.: 0, Max.: 255 Number of stored DTCs -


ACTIVE TEST


HINT:

Using the GTS or Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Body Electrical / IMB / Active Test.


e.

Perform the Active Test according to the display on the GTS or Techstream.

Body Electrical > IMB > Active Test
Tester Display Control Range Inspection Item Diagnostic Note
Immobilizer amp drive ON/OFF Transponder key coil Output the electric wave from the antenna coil of the Immobiliser
Security indicator ON/OFF Combination meter assembly (security indicator light) The test is possible when the following condition is met: The key is in the ignition key cylinder.