Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM › from 2015.08
RM19Y0E _58 Vehicle Interior _003006 THEFT DETERRENT / KEYLESS ENTRY _0015192 ENGINE IMMOBILISER SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  B2792/13  Antenna Coil Open / Short  B2796/12  Transponder / Antenna Coil Malfunction  


DESCRIPTION

The antenna coil receives key code signals from the transponder chip in the key grip. The antenna coil is built into the transponder key coil, which amplifies the key code signals and outputs the signals to the transponder key ECU assembly.

DTC B2792/13 is stored when there is an open in the antenna coil.

DTC B2796/12 is stored when after the immobiliser coil is energized, no response is received from the key.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2792/13 Antenna Coil Open / Short The antenna coil built into the transponder key coil is open (determined by communication with transponder key ECU assembly) (1 trip detection logic*).
·

Terminal COL+ or COL- is open.

·

The antenna coil built into the transponder key coil is open.


·

Wire harness or connector

·

Transponder key coil

·

Transponder key ECU assembly


DTC Output Confirmation Operation

·

Insert the key into the ignition key cylinder.



B2796/12 Transponder / Antenna Coil Malfunction After the immobiliser coil is energized, no response is received from the key
·

Wire harness or connector

·

Transponder key coil

·

Transponder key ECU assembly


DTC Output Confirmation Operation

·

Insert the key into the ignition key cylinder.




*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started -

Related Data List and Active Test
DTC No. Data List and Active Test
B2792/13 -
B2796/12 -

WIRING DIAGRAM

B366391E02
4.635,2.198 6.927,2.615 2.292,0.417 10 false Transponder Key ECU Assembly 5.219,0.708 5.729,1.021 0.51,0.313 10 false COL+ 5.24,1.635 5.75,1.948 0.51,0.313 10 false COL- 4.99,0.594 5.219,0.854 0.229,0.26 10 false 5 4.938,1.521 5.271,1.792 0.333,0.271 10 false 16 2.438,0.594 2.813,0.917 0.375,0.323 10 false 1 1.927,0.594 2.438,0.906 0.51,0.313 10 false COL+ 1.979,1.531 2.49,1.844 0.51,0.313 10 false COL- 2.438,1.531 2.844,1.875 0.406,0.344 10 false 5 0.917,2.177 2.396,2.573 1.479,0.396 10 false Transponder Key Coil 4.646,2.021 5.052,2.323 0.406,0.302 10 false E58 0.927,2.01 1.333,2.313 0.406,0.302 10 false E80 0.906,1.135 1.49,1.75 0.583,0.615 10 false Antenna Coil

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the transponder key ECU assembly, refer to the Service Bulletin.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > IMB > Clear DTCs
50002 586
Result:
Proceed to
NEXT




NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > IMB > Trouble Codes
50001 586
OK:

DTC B2792/13 is not output.


Result:
Proceed to
OK
NG




OK

NG

3.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - TRANSPONDER KEY COIL)
3.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - TRANSPONDER KEY COIL)
a.

Disconnect the E58 transponder key ECU assembly connector.


b.

Disconnect the E80 transponder key coil connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
E58-5 (COL+) - E80-1 (COL+) Always Below 1 Ω
E58-16 (COL-) - E80-5 (COL-) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
E58-5 (COL+) or E80-1 (COL+) - Body ground Always 10 kΩ or higher
E58-16 (COL-) or E80-5 (COL-) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

4.REPLACE TRANSPONDER KEY COIL

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE TRANSPONDER KEY COIL
a.

Replace the transponder key coil with a new one.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>TRANSPONDER KEY AMPLIFIER>REMOVAL

Result:
Proceed to
NEXT




NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > IMB > Trouble Codes
50001 586
OK:

DTC B2792/13 is not output.


Result:
Proceed to
OK
NG




OK

END (TRANSPONDER KEY COIL WAS DEFECTIVE)

NG

REPLACE TRANSPONDER KEY ECU ASSEMBLY