Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM › from 2015.08
RM19Y0E _58 Vehicle Interior _003006 THEFT DETERRENT / KEYLESS ENTRY _0015192 ENGINE IMMOBILISER SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  Security Indicator Light Does not Blink  


DESCRIPTION

When the engine immobiliser system is set, the security indicator light blinks continuously, but does not illuminate if the engine immobiliser system is not set.

WIRING DIAGRAM

E317949E02
2.104,0.802 2.979,1.125 0.875,0.323 10 false ECU-B 2.063,1.292 2.938,1.615 0.875,0.323 10 false ECU IG2 3.156,0.646 4.208,1.01 1.052,0.365 10 false from Battery 3.156,1.125 5.677,1.531 2.521,0.406 10 false from No. 1 Integration Relay 0.26,3.219 2.771,3.625 2.51,0.406 10 false Transponder Key ECU Assembly 4.604,2.417 6.594,2.833 1.99,0.417 10 false Combination Meter Assembly 4.615,2.26 5.052,2.573 0.438,0.313 10 false E34 4.698,1.708 5.135,2.021 0.438,0.313 10 false 26 6.052,1.708 6.49,2.021 0.438,0.313 10 false 7 5,1.833 5.719,2.219 0.719,0.385 10 false SECR 5.802,1.833 6.24,2.146 0.438,0.313 10 false E 1.24,1.813 1.813,2.115 0.573,0.302 10 false IND 1.573,1.719 1.927,2 0.354,0.281 10 false 12 1.573,2.51 1.927,2.792 0.354,0.281 10 false 14 1.354,2.625 1.792,2.938 0.438,0.313 10 false E 1.333,1.125 1.688,1.406 0.354,0.281 10 false IG 1.271,0.646 1.625,0.927 0.354,0.281 10 false +B 1.583,0.552 1.938,0.833 0.354,0.281 10 false 1 1.604,1.031 1.958,1.313 0.354,0.281 10 false 2 0.26,3.052 0.698,3.365 0.438,0.313 10 false E58

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the transponder key ECU assembly, refer to the Service Bulletin.

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > IMB > Trouble Codes
50001 586
OK:

DTC is not output.


Result:
Proceed to
OK
NG




OK

2.PERFORM ACTIVE TEST USING GTS OR TECHSTREAM (SECURITY INDICATOR)

NG

2.PERFORM ACTIVE TEST USING GTS OR TECHSTREAM (SECURITY INDICATOR)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Body Electrical / IMB / Active Test.


e.

Perform the Active Test according to the display on the GTS or Techstream.

Body Electrical > IMB > Active Test
Tester Display Control Range Inspection Item Diagnostic Note
Security indicator ON/OFF Combination meter assembly (security indicator light) The test is possible when the following condition is met: The key is in the ignition key cylinder.
Body Electrical > IMB > Active Test
Tester Display
Security indicator
50004 586 2
OK:

Combination meter assembly (security indicator light) can be turned on and off using the GTS or Techstream.


Result:
Proceed to
OK
NG




OK

3.READ VALUE USING GTS OR TECHSTREAM (IMMOBILISER CONDITION)

NG

5.CHECK HARNESS AND CONNECTOR (BTRANSPONDER KEY ECU ASSEMBLY - COMBINATIN METER ASSEMBLY AND BODY GROUND)
3.READ VALUE USING GTS OR TECHSTREAM (IMMOBILISER CONDITION)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Body Electrical / IMB / Data List.


e.

Read the Data List according to the display on the GTS or Techstream.

Body Electrical > IMB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Immobilizer condition Immobiliser system status determined by transponder key ECU assembly UNSET or SET UNSET: Immobiliser unset (engine start permitted [key inserted in ignition key cylinder])
SET: Immobiliser set (engine start prohibited [no key in ignition key cylinder])
-
Body Electrical > IMB > Data List
Tester Display
Immobilizer condition
50003 586 6
OK:

On the GTS or Techstream screen, the display changes between Set and Unset as shown in the table above.



Result:
Proceed to
OK
NG



OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

4.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - BATTERY AND BODY GROUND)
4.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - BATTERY AND BODY GROUND)
B242622C06
1.521,0.302 1.938,0.552 0.417,0.25 2.177,1.396 2.333,1.948 2.333,1.948 2.469,1.948 true 0.906,1.094 0.771,0.677 0.771,0.677 0.583,0.677 true 1.063,1.094 0.875,0.406 0.875,0.406 0.688,0.406 true 0.115,0.073 0.521,0.385 0.406,0.313 10 false *a 0.354,0.604 0.792,0.969 0.438,0.365 10 false +B 2.531,1.865 2.885,2.115 0.354,0.25 10 false E 0.5,0.323 0.958,0.625 0.458,0.302 10 false IG 1.604,0.354 2.219,0.74 0.615,0.385 10 false E58
*a Front view of wire harness connector
(to Transponder Key ECU Assembly)


a.

Disconnect the E58 transponder key ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E58-14 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E58-1 (+B) - Body ground Always 11 to 14 V
E58-2 (IG) - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG




OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (BTRANSPONDER KEY ECU ASSEMBLY - COMBINATIN METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the E58 transponder key ECU assembly connector.


b.

Disconnect the E34 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
E58-12 (IND) - E34-26 (SECR) Always Below 1 Ω
E34-7 (E) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
E58-12 (IND) or E34-26 (SECR) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

6.CHECK TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK TRANSPONDER KEY ECU ASSEMBLY
a.
B396096C03
1.479,0.5 1.896,0.75 0.417,0.25 1.854,2.083 1.667,2.083 1.667,2.083 1.542,1.469 true 0.927,2.083 1.115,2.083 1.115,2.083 1.25,1.458 true 0.156,0.104 0.542,0.427 0.385,0.323 10 false *a 1.563,0.552 2.073,0.844 0.51,0.292 10 false E58 1.938,2 2.417,2.271 0.479,0.271 10 false IND 2.656,3.396 3.135,3.667 0.479,0.271 10 false GND 0.781,2.01 1.073,2.26 0.292,0.25 10 false E
*a Component with harness connected
(Transponder Key ECU Assembly)


Reconnect the E58 transponder key ECU assembly connector.


b.

Using an oscilloscope, check the waveform.

Measurement Condition:
Item Content
Tester Connection E58-12 (IND) - E58-14 (E)
Tool Setting 5 V/DIV., 500 ms./DIV.
Condition No key in ignition key cylinder


OK:

Waveform is output normally (refer to illustration).



Result:
Proceed to
OK
NG



OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPLACE COMBINATION METER ASSEMBLY