Home › Drivetrain › CLUTCH › CLUTCH PEDAL(for 1NR-VE) › from 2015.08
RM19Y0E _52 Drivetrain _002984 CLUTCH _0197226 CLUTCH PEDAL(for 1NR-VE) N

CLUTCH  CLUTCH PEDAL(for 1NR-VE)  ADJUSTMENT  


PROCEDURE

Hide 31301 1.INSPECT AND ADJUST CLUTCH PEDAL SUB-ASSEMBLY

C331601C01
1.948,1.781 2.385,2.094 false 1.74,1.875 2.031,2.344 false 2.563,3.958 2.875,4.156 0.313,0.198 10 false *a 2.448,2.052 2.76,2.25 0.313,0.198 10 false *1 2.042,2.375 2.354,2.573 0.313,0.198 10 false *2
*1 Clutch Start Switch Assembly
*2 Lock Nut
*a Pedal Height


a.

Turn back the floor carpet to expose the asphalt sheet under the pedal.


b.

Check that the pedal height is correct using a vernier caliper.

Pedal height from floor panel (Excluding asphalt sheet):

167.9 mm (6.610 in.)


Pedal height from floor carpet (Reference):

150.0 mm (5.910 in.)



c.

Adjust the pedal height.

i.

Loosen the lock nut of the clutch start switch assembly and adjust the pedal height by turning the clutch start switch assembly.


ii.

Tighten the lock nut.

Torque:
11.8 N*m (120 kgf*cm, 9 ft.*lbf)



Hide 2.INSPECT AND ADJUST CLUTCH PEDAL FREE PLAY

C151156C01
2.458,1.875 2.625,2.042 0.167,0.167 10 *a
*a Pedal Free Play


a.

Lightly push the pedal by hand and check that the pedal free play is correct.

Standard:

15 to 25 mm (0.591 to 0.984 in.)



b.
C150628C01
1.635,0.667 2.031,0.917 false 2.052,1.75 2.427,1.469 false 1.458,0.573 1.667,0.74 0.208,0.167 10 *1 1.865,1.698 2.063,1.865 0.198,0.167 10 *2
*1 Nut
*2 Grommet


Adjust the pedal free play.

i.

Pull the clutch outer cable towards the front of the vehicle. Stop pulling the cable when the clutch release bearing hub touches the clutch cover diaphragm spring.


ii.

Turn the adjusting nut until the clearance between the nut and the grommet is between 3 to 6 mm (0.118 to 0.236 in.).


iii.

Align the protruding part of the grommet with the closest recess of the adjusting nut and set them in that position.


iv.

Check that clutch pedal free play is within the specified range.



Hide 3.INSPECT CLUTCH RELEASE POINT

CL00512C02
1.552,1.604 2.104,1.021 true 0.875,1.563 1.292,1.552 true 1.313,1.125 1.49,1.323 0.177,0.198 10 *b 1.74,1.948 1.917,2.146 0.177,0.198 10 *d 2.135,0.906 2.302,1.104 0.167,0.198 10 *c 0.656,1.49 0.844,1.719 0.188,0.229 10 *a
*a Full Stroke end Position
*b From Pedal Stroke end Position to Release Point
*c Release Point
*d Pedal Stroke


a.

While the engine is idling, ensure the parking brake is engaged with the brake pedal depressed. Under this condition, move the shift lever into first gear and gradually release the clutch pedal. Inspect the pedal stroke distance from the full stroke end position to the point immediately before the clutch is engaged (release point).

Standard:

25 mm (0.984 in.) or more

(From pedal stroke end position to release point)


Pedal stroke (Reference):

150 mm (5.905 in.)


If the distance is not as specified, perform the following operations.

·

Check the pedal height

·

Check the pedal free play

·

Check the clutch release cable

·

Check the clutch cover and the clutch disc