Home › Drivetrain › CLUTCH › CLUTCH PEDAL(for 2NR-VE) › from 2015.08
RM19Y0E _52 Drivetrain _002984 CLUTCH _0197227 CLUTCH PEDAL(for 2NR-VE) N

CLUTCH  CLUTCH PEDAL(for 2NR-VE)  ADJUSTMENT  


PROCEDURE

Hide 31301 1.INSPECT AND ADJUST CLUTCH PEDAL SUB-ASSEMBLY

a.

Pull back the floor carpet.


b.
C331590C01
1.396,0.854 1.958,0.26 true 1.802,1.615 2.323,1.76 true 2,0.104 2.313,0.302 0.313,0.198 10 false *a 2.385,1.677 2.698,1.875 0.313,0.198 10 false *b 1.917,4.01 2.229,4.208 0.313,0.198 10 false *c 2.75,4.083 3.063,4.281 0.313,0.198 10 false *d
*a Push Rod and Free Play Adjustment Point
*b Pedal Height Adjustment Point
*c Pedal Stroke
*d Pedal Height


Check that the pedal height is correct.

Pedal height from floor panel (Excluding asphalt sheet):

164.1 mm (6.461 in.)


Pedal height from floor carpet (Reference):

142.0 mm (5.590 in.)



c.

Adjust the pedal height.

i.

Loosen the lock nut of the clutch start switch assembly and adjust the pedal height by turning the clutch start switch assembly.

Torque:
11.8 N*m (120 kgf*cm, 9 ft.*lbf)



Hide 2.INSPECT AND ADJUST PEDAL FREE PLAY AND PUSH ROD PLAY

a.

Check that the pedal free play and push rod play are correct.

HINT:

Pay close attention to the change in resistance to distinguish between pedal free play and push rod play while performing the inspection.


i.
D031462C01
1.833,1.615 2.031,1.76 0.198,0.146 10 *a 1.875,1.927 2.083,2.083 0.208,0.156 10 *b
*a Push Rod Play
*b Pedal Free Play


Depress the pedal until the clutch resistance begins to be felt.

Pedal free play:

3.0 to 20.0 mm (0.118 to 0.787 in.)



ii.

Gently depress the pedal until the resistance begins to increase a little.

Push rod play at pedal top:

1.0 to 8.0 mm (0.039 to 0.315 in.)




b.

If necessary, adjust the pedal free play and push rod play.

HINT:

The push rod play can be adjusted by changing the length of the push rod. Pedal free play changes together with push rod play.


i.

Loosen the lock nut and turn the push rod until the free play and push rod play are correct.

NOTICE:

If pedal free play and push rod play are not within the standard range even after adjustment, inspect the related parts.



ii.

Tighten the lock nut.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


iii.

After adjusting the pedal free play and push rod play, check the pedal height.



Hide 3.INSPECT CLUTCH RELEASE POINT

a.
CL00512C01
1.552,1.604 2.104,1.021 true 0.844,1.563 1.26,1.552 true 1.323,1.104 1.5,1.302 0.177,0.198 10 *b 1.74,1.948 1.917,2.146 0.177,0.198 10 *d 2.135,0.885 2.302,1.083 0.167,0.198 10 *c 0.625,1.469 0.813,1.698 0.188,0.229 10 *a
*a Full Stroke end Position
*b From Pedal Stroke end Position to Release Point
*c Release Point
*d Pedal Stroke


Check the clutch release point.

i.

Pull the parking brake lever and chock the wheels.


ii.

Start the engine and allow it to idle.


iii.

Without depressing the clutch pedal, slowly move the shift lever into the reverse position until the gears engage.


iv.

Gradually depress the clutch pedal and measure the stroke distance from the point that the gear noise stops (release point) up to the full stroke end position.

Standard distance:

25 mm (0.984 in.) or more

(From pedal stroke end position to release point)


Pedal stroke(Reference):

142.5 mm (5.610 in.)


If the distance is not as specified, perform the following operations.

·

Check the pedal height.

·

Check the push rod play and pedal free play.

·

Bleed the clutch line.

·

Check the clutch cover assembly and disc assembly.