Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL CARRIER ASSEMBLY(for 1NR-VE) › from 2015.08
RM19Y0E _52 Drivetrain _002987 AXLE AND DIFFERENTIAL _0197235 REAR DIFFERENTIAL CARRIER ASSEMBLY(for 1NR-VE) A

AXLE AND DIFFERENTIAL  REAR DIFFERENTIAL CARRIER ASSEMBLY(for 1NR-VE)  REASSEMBLY  


PROCEDURE

Hide 41311J 1.ASSEMBLE REAR DIFFERENTIAL CASE

a.
C336083

Install the rear differential side gear thrust washer onto the rear differential side gear.


b.
C197100

Install the rear differential side gears, pinion gears and pinion shaft onto the differential case.


c.
C197101

Using a dial indicator, measure the differential case backlash while holding the pinion toward the case.

Backlash:

0 to 0.075 mm (0 to 0.0030 in.)


If the backlash is not within the specification, install 2 side gear thrust washers of a different thickness.

Thrust washer thickness:
Thickness mm (in.) Thickness mm (in.)
1.10 (0.0433) 1.25 (0.0492)
1.15 (0.0453) 1.30 (0.0512)
1.20 (0.0472) 1.35 (0.0531)



Hide 2.INSTALL DIFFERENTIAL RING GEAR

a.

Clean the contact surfaces of the differential case and ring gear.


b.
C145177C03
2.135,1.438 2.885,1.781 2.885,1.781 2.219,1.594 true 2.979,1.698 3.365,2.042 0.385,0.344 10 *a
*a Matchmark


Align the matchmarks on the ring gear with those of the differential case.

NOTICE:
·

Align the bolt holes in the differential case with the screw holes in the differential ring gear.

·

If it is difficult to install the ring gear, wrap the gear in a cloth to protect it, and tap the outer edge of the gear evenly with a plastic hammer.




c.

Temporarily install the 10 bolts.


d.

Install the 10 bolts by diametrically tightening the bolts uniformly in several steps.

Torque:
97 N*m (989 kgf*cm, 72 ft.*lbf)


Hide 41301A 3.INSTALL REAR DIFFERENTIAL CASE BEARING

a.
C197102C02
0.51,0.167 0.667,0.25 false 0.698,0.563 0.333,0.656 0.333,0.656 0.594,0.854 false 0.323,0.094 0.74,0.458 0.417,0.365 10 *1 0.052,0.583 0.677,0.979 0.625,0.396 10 SST
*1 Press


Using SST and a press, press the bearing RH onto the differential case.

SST
09950-60010  (09951-00500)
09950-70010  (09951-07150)


b.
C145180C02
2.688,0.396 2.906,0.396 false 2.646,0.656 2.969,0.76 2.969,0.76 2.667,0.802 false 2.938,0.313 3.281,0.667 0.344,0.354 10 *1 3.021,0.667 3.427,1.042 0.406,0.375 10 SST
*1 Press


Using SST and a press, press the bearing LH onto the differential case.

SST
09950-60010  (09951-00490, 09951-00500)
09950-70010  (09951-07150)


Hide 4.INSPECT DIFFERENTIAL RING GEAR RUNOUT

a.
C145169

Install the differential case on the carrier, and install the 2 adjusting nuts so that there is no play in the bearing.


b.

Install the 2 bearing caps with the 4 bolts.

Torque:
84 N*m (857 kgf*cm, 62 ft.*lbf)


c.

Using a dial indicator, measure the runout of the ring gear.

Maximum runout:

0.10 mm (0.0039 in.)



d.

Remove the 2 bearing caps, 2 adjusting nuts and the differential case.


Hide 41201B 5.INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C145181N03
1.865,0.698 2.229,0.615 2.229,0.615 1.906,0.99 false 2.292,0.552 2.802,0.906 0.51,0.354 10 SST

Using SST and a press, press in the roller bearing (outer) to the carrier.

SST
09950-60010  (09951-00620)
09950-70010  (09951-07150)


Hide 41201D 6.INSTALL REAR DIFFERENTIAL DRIVE PINION PLATE WASHER

a.

Install the rear differential drive pinion washer that was removed during the disassembly.

NOTICE:

Inspect the rear differential drive pinion washer.

If there is any wear, scratches or other defects, install a new rear differential drive pinion washer of the same thickness.



Hide 41201A 7.INSTALL REAR DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C145182N01
1.604,0.76 2.104,0.542 2.104,0.542 1.698,1.052 true 2.135,0.458 2.667,0.823 0.531,0.365 10 SST

Using SST and a press, press the roller bearing (outer) into the carrier.

SST
09950-60020  (09951-00720)
09950-70010  (09951-07150)


b.
C145183N03
1.75,1.167 2.365,0.948 true 2.438,0.854 2.979,1.26 0.542,0.406 10 SST

Install the plate washer onto the drive pinion.

HINT:

First fit a washer with the same thickness as the removed washer, and then check the tooth contact pattern. Replace the washer with one of a different thickness if necessary.



c.

Using SST and a press, press the roller bearing (inner) onto the drive pinion.

SST
09506-30012  


Hide 8.ADJUST DIFFERENTIAL DRIVE PINION PRELOAD

a.
F001250

Install the drive pinion and rear drive pinion front tapered roller bearing.

HINT:

Assemble the spacer and oil seal after adjusting the gear contact pattern.



b.
C111780C03
2.302,0.229 1.896,0.208 1.896,0.208 2.073,0.573 false 1.563,0.104 2.073,0.427 0.51,0.323 10 SST 3.052,0.823 3.365,1.135 0.313,0.313 10 *a 1.552,0.833 1.906,1.083 0.354,0.25 10 *b
*a Turn
*b Hold


Using SST, install the companion flange.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09956-03020, 09955-03030)

NOTICE:

Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



c.
C145188C03
1.354,0.667 1.01,0.615 false 0.958,3.208 1,3.385 1,3.385 1.375,3.042 true 0.26,2.208 0.688,2.552 0.427,0.344 10 *B 0.26,0.052 0.656,0.417 0.396,0.365 10 *A 0.667,0.531 1.396,1.208 0.729,0.677 10 SST 0.823,3.417 1.417,3.781 0.594,0.365 10 SST
*A for Manual Transmission
*B for Automatic Transmission


Using SST to hold the companion flange in place, adjust the drive pinion preload by tightening a new companion flange nut.

NOTICE:

As there is no spacer, torque a little at a time. Be careful not to overtighten the nut.


i.

for Manual Transmission:

SST
09330-87301  


ii.

for Automatic Transmission:

SST
09330-00021  
09950-30012  (09955-03030)



d.
C003092

Using a torque wrench, measure the preload.

Preload (at starting):

0.57 to 0.96 N*m (5.8 to 9.8 kgf*cm, 5.0 to 8.5 in.*lbf)


NOTICE:

For a more accurate measurement, rotate the bearing forward and backward several times before measuring.


HINT:

Make a note of the values for the below total preload inspection procedure.



Hide 41311J 9.INSTALL REAR DIFFERENTIAL CASE

a.
C197103

Place the 2 bearing outer races on their respective bearings.

HINT:

Do not interchange the right and left races.



Hide 41315 10.INSTALL REAR DIFFERENTIAL BEARING ADJUSTING NUT

a.
C197104

Install the 2 adjusting nuts onto the carrier, making sure the nuts are threaded properly.


Hide 11.INSPECT AND ADJUST DIFFERENTIAL RING GEAR AND DIFFERENTIAL DRIVE PINION BACKLASH

a.
C145174C08
1.771,1.333 1.396,1.906 1.396,1.906 1.781,1.458 true 1.229,1.896 1.646,2.177 0.417,0.281 10 *a
*a Matchmark


Align the matchmarks on the cap and carrier.


b.
C197105

Install the right and left bearing caps with the 4 bolts.

Torque:
84 N*m (857 kgf*cm, 62 ft.*lbf)

If the bearing cap does not fit tightly on the carrier, the adjusting nuts are not threaded properly.

HINT:

Reinstall the adjusting nuts if necessary.




c.
C267771C02
0.135,0.083 0.677,0.479 0.542,0.396 10 *a 2.729,0.24 3.271,0.635 0.542,0.396 10 SST
*a LH Side


Loosen the 4 bearing cap bolts to the point where the adjusting nuts can be turned using SST.


d.

Using SST, torque the adjusting nut on the ring gear side until the ring has a backlash of about 0.15 mm (0.006 in.).

SST
09504-00011  


e.
C267772C02
0.115,0.083 0.76,0.563 0.646,0.479 10 *a 1.083,1.708 1.49,2.073 0.406,0.365 10 SST
*a RH Side


While turning the ring gear, use SST to fully tighten the adjusting nut on the drive pinion side. After the bearings have settled, loosen the adjusting nut on the drive pinion side.


f.

Using SST, tighten the adjusting nut 1 to 2 notches from the 0 preload position.

SST
09504-00011  


g.
C267773N02
1.531,1.99 2.135,2.167 0.604,0.177 10 SST

Using a dial indicator, adjust the ring gear backlash until it is within the specification.

Standard backlash:

0.08 to 0.13 mm (0.0031 to 0.0052 in.)


HINT:
·

The backlash is adjusted by turning the left and right adjusting nuts an equal amount. For example, loosen the nut on the right side one notch and loosen the nut on the left side one notch.

·

Perform the measurement at 3 or more positions around the circumference of the ring gear.




h.
C145174

Torque the bearing cap bolts.

Torque:
84 N*m (857 kgf*cm, 62 ft.*lbf)


Hide 12.INSPECT TOTAL PRELOAD

a.
C003092

Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

Total preload (at starting):

Drive pinion preload plus 0.20 to 0.39 N*m (2.0 to 4.0 kgf*cm, 1.77 to 3.45 in.*lbf)


If necessary, disassemble and inspect the differential.


Hide 13.INSPECT TOOTH CONTACT BETWEEN RING GEAR AND DRIVE PINION

a.
C014071

Coat 3 or 4 teeth at 3 different positions on the ring gear with prussian blue.


b.

Hold the companion flange firmly in place and rotate the ring gear in both directions.


c.

Inspect the tooth contact pattern.

If the teeth are not engaged properly, use the following chart to select a proper washer.

C289711C02
0.583,1.25 0.896,1.406 0.313,0.156 10 false *a 3.083,0.25 3.396,0.406 0.313,0.156 10 false *b 6.417,0.75 6.729,0.906 0.313,0.156 10 false *c 3.083,2.583 3.396,2.74 0.313,0.156 10 false *d 6.417,3.083 6.729,3.24 0.313,0.156 10 false *e 4.833,1.594 5.146,1.75 0.313,0.156 10 false *f 4.833,4.042 5.167,4.292 0.333,0.25 10 false *g
*a Proper Contact *b Heel Contact
*c Face Contact *d Toe Contact
*e Frank Contact *f Select an adjusting washer that brings the drive pinion closer to the ring gear.
*g Select an adjusting washer that shifts the drive pinion away from the ring gear. - -


Plate Washer Thickness:
Thickness mm (in.) Thickness mm (in.)
0.29 (0.0114) 0.50 (0.0197)
0.32 (0.0126) 0.53 (0.0209)
0.35 (0.0138) 0.56 (0.0220)
0.38 (0.0150) 0.59 (0.0232)
0.41 (0.0161) 0.62 (0.0244)
0.44 (0.0173) 0.65 (0.0256)
0.47 (0.0185) -




Hide 14.REMOVE REAR DRIVE PINION NUT

a.
C145171C05
1.938,0.74 2.177,0.49 true 1.896,2.896 2.177,2.771 2.177,2.771 1.969,3.052 true 0.115,2.208 0.625,2.594 0.51,0.385 10 *B 0.115,0.104 0.594,0.49 0.479,0.385 10 *A 2.25,0.385 2.781,0.719 0.531,0.333 10 SST 2.24,2.677 2.813,3.01 0.573,0.333 10 SST
*A for Manual Transmission
*B for Automatic Transmission


Using SST to hold the companion flange in place, remove the nut.

i.

for Manual Transmission:

SST
09330-87301  


ii.

for Automatic Transmission:

SST
09330-00021  
09950-30012  (09955-03030)



Hide 41204 15.REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

Hide 41201B 16.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

Hide 41231 17.INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER

a.
C289992

Install the bearing spacer onto the drive pinion.

NOTICE:

Install the spacer so that the larger diameter end is facing the rear of the vehicle.



Hide 41201E 18.INSTALL REAR DIFFERENTIAL DRIVE PINION SPACER FRONT ADJUST SHIM

a.

Install the drive pinion spacer front adjust shim that was removed during the disassembly.

NOTICE:

Inspect the drive pinion spacer front adjust shim. If there is any wear, scratches or other defects, install a new drive pinion spacer front adjust shim of the same thickness.



Hide 41201B 19.INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

Hide 41204 20.INSTALL REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

a.
C111780C06
2.302,0.229 1.896,0.177 1.896,0.177 2.073,0.573 false 1.563,0.104 2.125,0.469 0.563,0.365 10 SST 3.052,0.823 3.427,1.167 0.375,0.344 10 *a 1.552,0.833 2.052,1.177 0.5,0.344 10 *b
*a Turn
*b Hold


Using SST, install the companion flange onto the drive pinion.

SST
09950-30012  (09951-03010, 09953-03010, 09955-03030, 09956-03020, 09954-03010)

NOTICE:

Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



b.
C145188C07
1.354,0.667 1.01,0.615 false 0.958,3.208 1,3.385 1,3.385 1.375,3.042 true 0.26,2.219 0.823,2.646 0.563,0.427 10 *B 0.26,0.042 0.802,0.469 0.542,0.427 10 *A 0.656,0.521 1.167,0.823 0.51,0.302 10 SST 0.875,3.479 1.458,3.813 0.583,0.333 10 SST
*A for Manual Transmission
*B for Automatic Transmission


Using SST to hold the flange, torque the nut.

Torque:
157 N*m (1600 kgf*cm, 116 ft.*lbf)

i.

for Manual Transmission:

SST
09330-87301  


ii.

for Automatic Transmission:

SST
09330-00021  09950-30012  (09955-03030)



Hide 21.INSPECT DRIVE PINION PRELOAD

a.
SA02352

Using a torque wrench, measure the preload of the backlash between the drive pinion and ring gear.

Preload (at starting):

0.57 to 0.96 N*m (5.8 to 9.8 kgf*cm, 5.0 to 8.5 in.*lbf)


NOTICE:

For a more accurate measurement, rotate the bearing forward and backward several times before measuring.



b.

If the starting torque is not within the specified range, select a rear differential drive pinion spacer front adjust shim according to the table below and adjust the starting torque.

Adjust shim Thickness:
Thickness mm (in.) Thickness mm (in.)
1.65 (0.0650) 2.10 (0.0827)
1.70 (0.0670) 2.15 (0.0846)
1.75 (0.0689) 2.20 (0.0866)
1.80 (0.0709) 2.25 (0.0886)
1.85 (0.0728) 2.30 (0.0906)
1.90 (0.0748) 2.35 (0.0925)
1.95 (0.0768) 2.40 (0.0945)
2.00 (0.0787) 2.45 (0.0965)
2.05 (0.0807) -


HINT:

Make a note of the values for the below total preload inspection procedure.



Hide 22.INSPECT TOTAL PRELOAD

a.
C003092

Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

Total preload (at starting):

Drive pinion preload plus 0.20 to 0.39 N*m (2.0 to 4.0 kgf*cm, 1.77 to 3.45 in.*lbf)


If necessary, disassemble and inspect the differential.


Hide 41204 24.REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

Hide 41201C 25.INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL

a.
C145189N03
1.323,1.083 1.563,0.677 false 1.625,0.594 2.156,0.885 0.531,0.292 10 SST

Apply MP grease to a new oil seal.


b.

Using SST and a hammer, tap in the oil seal.

SST
09554-22010  

Oil seal depth:

0 to 1.0 mm(0 to 0.039 in.)



Hide 41252 26.INSTALL REAR DIFFERENTIAL DUST DEFLECTOR

HINT:

If the dust deflector has been removed due to damage or deformation, replace it with a new one.


a.
C145190N02
0.448,0.458 0.906,0.729 false 0.115,0.354 0.573,0.552 0.458,0.198 10 false SST

Using SST and a press, install a new dust deflector.

SST
09523-36010  
09950-60010  (09951-00570)

CAUTION:

Be careful not to damage the dust deflector.



Hide 41204 27.INSTALL REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

a.
C111780C04
2.302,0.229 1.896,0.177 1.896,0.177 2.073,0.573 false 1.563,0.104 2.125,0.469 0.563,0.365 10 SST 3.052,0.823 3.427,1.167 0.375,0.344 10 *a 1.552,0.833 2.052,1.177 0.5,0.344 10 *b
*a Turn
*b Hold


Using SST, install the companion flange onto the drive pinion.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020)

NOTICE:

Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



b.
C145188C06
1.354,0.667 1.01,0.615 false 0.958,3.208 1,3.385 1,3.385 1.375,3.042 true 0.26,2.219 0.823,2.646 0.563,0.427 10 *B 0.26,0.042 0.802,0.469 0.542,0.427 10 *A 0.656,0.521 1.167,0.823 0.51,0.302 10 SST 0.875,3.479 1.458,3.813 0.583,0.333 10 SST
*A for Manual Transmission
*B for Automatic Transmission


Using SST to hold the flange, torque the nut.

Torque:
157 N*m (1600 kgf*cm, 116 ft.*lbf)

i.

for Manual Transmission:

SST
09330-87301  


ii.

for Automatic Transmission:

SST
09330-00021  
09950-30012  (09955-03030)



Hide 28.INSPECT DIFFERENTIAL RING GEAR BACKLASH

a.
C028211

Using a dial indicator, check the backlash of the ring gear.

Standard backlash:

0.08 to 0.13 mm (0.0031 to 0.0052 in.)


If the backlash is not as specified, adjust the side bearing preload or repair as necessary.

HINT:

Perform the measurements at 3 or more positions around the circumference of the ring gear.




Hide 41204 29.INSPECT RUNOUT OF REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

a.
C231133C04
2.198,0.094 2.635,0.458 0.438,0.365 10 *b 0.469,0.083 0.844,0.417 0.375,0.333 10 *a 2.281,1.833 2.667,2.167 0.385,0.333 10 *c
*a Vertical Runout
*b Lateral Runout
*c 30 mm (1.18 in.)


Using a dial indicator, measure the runout of the drive pinion companion flange vertically and laterally.

Maximum runout:
Runout Maximum
Vertical runout 0.10 mm (0.0039 in.)
Lateral runout 0.10 mm (0.0039 in.)


If the runout is greater than the maximum, replace the companion flange.



Hide 30.STAKE REAR DRIVE PINION NUT

a.
ZK07449

Using a chisel and hammer, stake the nut.


Hide 41316 31.INSTALL REAR DIFFERENTIAL BEARING ADJUSTING NUT LOCK

a.
C145173

Install 2 new adjusting nut locks onto the bearing caps with the 2 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


b.

Bend the nut locks.

HINT:

Perform the measurements at 3 or more positions around the circumference of the ring gear.