Home › Vehicle Interior › DOOR LOCK › KEY REMINDER WARNING SYSTEM › from 2015.08
RM19Y0E _58 Vehicle Interior _003005 DOOR LOCK _0015188 KEY REMINDER WARNING SYSTEM U

DOOR LOCK  KEY REMINDER WARNING SYSTEM  TERMINALS OF ECU  


CHECK MAIN BODY ECU (FUSE BLOCK ASSEMBLY)


E317948N01
0.781,4.688 1.198,4.938 0.417,0.25 1.896,4.688 2.313,4.938 0.417,0.25 1.323,5.698 1.74,5.948 0.417,0.25 0.594,6.823 1.01,7.073 0.417,0.25 2.031,6.813 2.448,7.063 0.417,0.25 1.344,7.75 1.76,8 0.417,0.25 5.885,6.813 6.302,7.063 0.417,0.25 4.26,4.698 4.677,4.948 0.417,0.25 5.844,4.677 6.26,4.927 0.417,0.25 5.854,5.688 6.271,5.938 0.417,0.25 4.219,5.698 4.635,5.948 0.417,0.25 4.25,6.813 4.667,7.063 0.417,0.25 1.781,2.885 2.167,3.177 0.385,0.292 10 false 3B 2.115,2.906 2.51,3.208 0.396,0.302 10 false 3C 1.708,3.219 2.115,3.5 0.406,0.281 10 false 3D 4.781,2.01 5.25,2.333 0.469,0.323 10 false 3E 4.792,2.625 5.167,2.917 0.375,0.292 10 false 3F 4.771,3.25 5.25,3.583 0.479,0.333 10 false 3G 1.344,3.479 1.74,3.781 0.396,0.302 10 false 3K 1.365,2.99 1.76,3.292 0.396,0.302 10 false 3L 4.521,3.802 4.917,4.104 0.396,0.302 10 false 3H 5.083,3.802 5.479,4.104 0.396,0.302 10 false 3I 5.604,3.792 6.083,4.167 0.479,0.375 10 false 3J 1.729,2.563 2.083,2.833 0.354,0.271 10 false 3A 0.906,4.729 1.333,5 0.427,0.271 10 false 3A 2.01,4.729 2.396,5.021 0.385,0.292 10 false 3B 1.448,5.74 1.917,6.083 0.469,0.344 10 false 3C 0.719,6.865 1.125,7.146 0.406,0.281 10 false 3D 5.979,5.74 6.417,6.083 0.438,0.344 10 false 3E 4.385,6.865 4.802,7.188 0.417,0.323 10 false 3F 6.01,6.865 6.427,7.188 0.417,0.323 10 false 3G 4.385,4.75 4.781,5.052 0.396,0.302 10 false 3H 6,4.729 6.396,5.031 0.396,0.302 10 false 3I 4.365,5.74 4.76,6.042 0.396,0.302 10 false 3J 1.469,7.802 1.865,8.104 0.396,0.302 10 false 3K 2.167,6.865 2.563,7.167 0.396,0.302 10 false 3L

a.

Disconnect the 3A and 3G main body ECU (fuse block assembly) connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connectors disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
3A-1 - Body ground B - Body ground Battery power supply Always 11 to 14 V
3G-1 - Body ground W-B - Body ground Ground Always Below 1 Ω
3G-11 - Body ground W - Body ground Ground Always Below 1 Ω
3G-12 - Body ground BR - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the 3A and 3G main body ECU (fuse block assembly) connectors.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
3I-5 - Body ground W - Body ground ACC power supply Ignition switch off Below 1 V
Ignition switch ACC 11 to 14 V
3C-6 - Body ground B - Body ground Ignition power supply Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
3G-15 - Body ground G - Body ground Unlock warning switch input No key in ignition key cylinder Below 1 V
Key inserted into ignition key cylinder 11 to 14 V
3L-14 - Body ground LG-B - Body ground*1
GR-B - Body ground*2
Door courtesy switch (driver side) input Driver side door open Below 1 V
Driver side door closed Pulse generation (See waveform)

If the result is not as specified, the main body ECU (fuse block assembly) may be malfunctioning.

*1: for LHD

*2: for RHD



e.

Inspect using an oscilloscope.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
B413858N01
2.958,0.979 3.427,1.458 0.469,0.479 10 false GND

Waveform (Reference)

Measurement Condition:
Item Content
Tester Connection 3L-14 - Body ground
Tool Setting 5 V/DIV., 10 ms./DIV.
Condition Driver side door closed