Home › Engine / Hybrid System › 2NR-VE ENGINE CONTROL › SFI SYSTEM(w/ Air Fuel Ratio Sensor) › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042272 2NR-VE ENGINE CONTROL _0196262 SFI SYSTEM(w/ Air Fuel Ratio Sensor) U

2NR-VE ENGINE CONTROL  SFI SYSTEM(w/ Air Fuel Ratio Sensor)  TERMINALS OF ECM  


A348484N05
2,0.5 2.417,0.75 0.417,0.25 4.333,0.5 4.75,0.75 0.417,0.25 2.083,0.542 2.479,0.906 0.396,0.365 10 false A24 4.417,0.542 4.813,0.906 0.396,0.365 10 false C50

HINT:

The standard voltage between each pair of the ECM terminals is shown in the table below. The appropriate conditions for checking each pair of the terminals are also indicated.

The result of checks should be compared with the standard voltage for that pair of terminals, and displayed in the "Specified Condition" column.

The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A24-1 (+B1) - C50-4 (E01) G - W-B Power source of ECM Ignition switch ON 11 to 14 V
A24-2 (+B2) - C50-5 (E02) G - W-B Power source of ECM Ignition switch ON 11 to 14 V
A24-6 (+BM) - C50-4 (E01) LG - W-B Power source of throttle actuator Ignition switch ON 11 to 14 V
A24-8 (FC2) - C50-4 (E01) BE - W-B Fuel pump control signal Ignition switch ON 11 to 14 V
Idling Below 1.5 V
A24-9 (FAN) - C50-4 (E01) LG - W-B*1
V - W-B*2
Cooling fan control signal Ignition switch ON, cooling fan off 11 to 14 V
Cooling fan on*1
Cooling fan on (Low)*2
Below 1.5 V
A24-10 (FAN2) - C50-4 (E01)*2 L - W-B Cooling fan control signal Ignition switch ON, cooling fan off 11 to 14 V
Cooling fan on (High) Below 1.5 V
A24-12 (REV) - C50-4 (E01) R - W-B Engine speed signal Idling with warm engine Pulse generation
(See waveform 1)
A24-13 (BAT) - C50-4 (E01) G - W-B Battery (for measuring battery voltage and for ECM memory) Always 11 to 14 V
A24-14 (IGSW) - C50-4 (E01) Y - W-B Ignition switch signal Ignition switch ON 11 to 14 V
A24-16 (MGC) - C50-4 (E01) P - W-B Magnet clutch control signal Ignition switch ON, magnetic clutch off 11 to 14 V
Magnetic clutch on Below 1.5 V
A24-19 (ETR) - C50-4 (E01) GR - W-B E-THRO relay operation signal Ignition switch ON Below 1.5 V
A24-22 (CLT) - C50-4 (E01)*3 B - W-B Clutch start switch signal Ignition switch ON, clutch pedal released Below 1.5 V
Ignition switch ON, clutch pedal depressed 11 to 14 V
A24-25 (HCAN) - C50-4 (E01) GR - W-B CAN communication line Ignition switch ON Pulse generation
(See waveform 2)
A24-26 (LCAN) - C50-4 (E01) W - W-B CAN communication line Ignition switch ON Pulse generation
(See waveform 3)
A24-28 (MRO) - C50-4 (E01) W - W-B EFI-MAIN relay operation signal Ignition switch ON Below 1.5 V
A24-29 (VCO) - A24-57 (E24) Y - BR Power source of air conditioner pressure sensor Ignition switch ON 4.75 to 5.25 V
A24-30 (VCP1) - A24-58 (EPA) L - R Power source of accelerator pedal sensor (for VPA) Ignition switch ON 4.5 to 5.5 V
A24-31 (VCP2) - A24-59 (EPA2) V - W Power source of accelerator pedal sensor (for VPA2) Ignition switch ON 4.5 to 5.5 V
A24-39 (CANH) - C50-4 (E01) R - W-B CAN communication line Ignition switch ON Pulse generation
(See waveform 2)
A24-40 (CANL) - C50-4 (E01) G - W-B CAN communication line Ignition switch ON Pulse generation
(See waveform 3)
A24-43 (ACAD) - A24-57 (E24) B - BR Air conditioner pressure sensor signal Ignition switch ON 0.5 to 4.8 V
A24-44 (VPA) - A24-58 (EPA) G - R Accelerator pedal sensor signal (for engine control) Ignition switch ON, accelerator pedal fully released 0.5 to 1.1 V
Ignition switch ON, accelerator pedal fully depressed 2.6 to 4.5 V
A24-45 (VPA2) - A24-59 (EPA2) GR - W Accelerator pedal sensor signal Ignition switch ON, accelerator pedal fully released 1.2 to 2.0 V
Ignition switch ON, accelerator pedal fully depressed 3.4 to 4.75 V
A24-46 (STR-) - C50-4 (E01) L - W-B Starter signal Cranking Below 1.5 V
Idling Below 1.5 V
A24-48 (STP) - C50-4 (E01) Y - W-B Stop light switch signal Brake pedal released Below 1.5 V
Brake pedal depressed 11 to 14 V
A24-54 (SIO2) - C50-4 (E01)*4 P - W-B Immobiliser communication Ignition switch ON Pulse generation
A24-60 (STSW) - C50-4 (E01) R - W-B Starter signal Cranking 11 to 14 V
Idling Below 1.5 V
A24-62 (ST1-) - C50-4 (E01) V - W-B Stop light switch signal (opposite of voltage at STP terminal) Ignition switch ON, brake pedal released 7.5 to 14 V
Ignition switch ON, brake pedal depressed Below 1.5 V
A24-63 (PBSW) - C50-4 (E01)*5 W-R - W-B Vacuum warning switch signal Ignition switch ON, brake pedal released 11 to 14 V
Ignition switch ON, brake pedal depressed Below 1.5 V
A24-64 (T) - C50-4 (E01) L - W-B Terminal EFIT of DLC3 Ignition switch ON 11 to 14 V
A24-68 (R) - C50-4 (E01)*3 V - W-B Back-up light switch signal Ignition switch ON, shift lever in R 11 to 14 V
Ignition switch ON, shift lever not in R Below 1.5 V
C50-1 (M+) - C50-3 (MR01) GR - W-B Throttle actuator operation signal (positive terminal) Idling with warm engine Pulse generation
(See waveform 4)
C50-2 (M-) - C50-3 (MR01) L - W-B Throttle actuator operation signal (negative terminal) Idling with warm engine Pulse generation
(See waveform 5)
C50-3 (MR01) - Body ground W-B - - Ground circuit of throttle actuator Always Below 1 Ω
C50-4 (E01) - Body ground W-B - - Ground circuit of ECM Always Below 1 Ω
C50-5 (E02) - Body ground W-B - - Ground circuit of ECM Always Below 1 Ω
C50-7 (AFHG) - Body ground W-B - - Ground circuit of air fuel ratio sensor heater Always Below 1 Ω
C50-8 (OXH1) - C50-4 (E01) B - W-B No. 2 oxygen sensor heater signal Ignition switch ON 11 to 14 V
Idling Below 3.0 V
C50-9 (AFM) - C50-7 (AFHG) Y - W-B Air fuel ratio sensor heater signal Idling Pulse generation
(See waveform 6)
C50-10 (OCV+) - C50-11 (OCV-) P - G Camshaft timing oil control valve signal (for intake camshaft) Idling with warm engine Pulse generation
(See waveform 7)
C50-12 (OCV2+) - C50-13 (OCV2-) GR - V Camshaft timing oil control valve signal (for exhaust camshaft) Idling with warm engine Pulse generation
(See waveform 8)
C50-18 (#10) - C50-4 (E01) R - W-B No. 1 fuel injector signal Ignition switch ON 11 to 14 V
Idling with warm engine Pulse generation
(See waveform 9)
C50-19 (#20) - C50-4 (E01) W - W-B No. 2 fuel injector signal Ignition switch ON 11 to 14 V
Idling with warm engine Pulse generation
(See waveform 9)
C50-20 (#30) - C50-4 (E01) B - W-B No. 3 fuel injector signal Ignition switch ON 11 to 14 V
Idling with warm engine Pulse generation
(See waveform 9)
C50-21 (#40) - C50-4 (E01) BR - W-B No. 4 fuel injector signal Ignition switch ON 11 to 14 V
Idling with warm engine Pulse generation
(See waveform 9)
C50-30 (OX) - C50-51 (OX-) B - W No. 2 oxygen sensor signal Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor Pulse generation
(See waveform 10)
C50-31 (AF+) - C50-4 (E01) R - W-B Air fuel ratio sensor signal Ignition switch ON 3.3 V*6
C50-32 (THW) - C50-100 (E2) V-Y - BR-W Engine coolant temperature sensor Idling with warm engine, engine coolant temperature 80°C (176°F) 0.2 to 1.0 V
C50-33 (VTHO) - C50-99 (ETA) B - W Throttle position sensor signal (for engine control) Ignition switch ON, accelerator pedal fully released 0.5 to 1.1 V
Ignition switch ON, accelerator pedal fully depressed 3.2 to 4.8 V
C50-40 (IG1) - C50-4 (E01) V-W - W-B No. 1 ignition coil signal Idling with warm engine Pulse generation
(See waveform 11)
C50-41 (IG2) - C50-4 (E01) BR-B - W-B No. 2 ignition coil signal Idling with warm engine Pulse generation
(See waveform 11)
C50-42 (IG3) - C50-4 (E01) G-R - W-B No. 3 ignition coil signal Idling with warm engine Pulse generation
(See waveform 11)
C50-43 (IG4) - C50-4 (E01) R-Y - W-B No. 4 ignition coil signal Idling with warm engine Pulse generation
(See waveform 11)
C50-50 (NSSP) - C50-4 (E01)*3 P-G - W-B Ground circuit Always Below 1 Ω
C50-52 (AF-) - C50-4 (E01) G - W-B Air fuel ratio sensor signal Ignition switch ON 2.9 V*6
C50-55 (VCTA) - C50-99 (ETA) R - W Power source of throttle position sensor (specific voltage) Ignition switch ON 4.5 to 5.5 V
C50-57 (VCN) - C50-101 (EN) GR-L - W-L Power source of crankshaft position sensor Ignition switch ON 4.5 to 5.5 V
C50-58 (VCG) - C50-102 (EGIN) P-B - GR-R Power source of camshaft position sensor (for intake camshaft) Ignition switch ON 4.5 to 5.5 V
C50-59 (VCG) - C50-103 (EGEX) W-R - B-W Power source of camshaft position sensor (for exhaust camshaft) Ignition switch ON 4.5 to 5.5 V
C50-74 (THA) - C50-100 (E2) R-L - BR-W Intake air temperature sensor Idling, intake air temperature 0 to 80°C (32 to 176°F) 0.5 to 3.5 V
C50-76 (VG) - C50-98 (E2G) V-R - GR-G Intake air flow meter signal Idling, shift lever in P or N, A/C switch off 0.5 to 3.0 V
C50-77 (VTA2) - C50-99 (ETA) G - W Throttle position sensor signal (for sensor malfunction detection) Ignition switch ON, accelerator pedal fully released 2.1 to 3.1 V
Ignition switch ON, accelerator pedal fully depressed 4.6 to 5.0 V
C50-79 (N) - C50-101 (EN) LG-R - W-L Crankshaft position sensor signal Idling with warm engine Pulse generation
(See waveform 12)
C50-80 (GIN) - C50-102 (EGIN) G-W - GR-R Camshaft position sensor signal (for intake camshaft) Idling with warm engine Pulse generation
(See waveform 13)
C50-81 (GEX) - C50-103 (EGEX) R-G - B-W Camshaft position sensor signal (for exhaust camshaft) Idling with warm engine Pulse generation
(See waveform 13)
C50-84 (MOPS) - C50-4 (E01) G-B - W-B Engine oil pressure switch signal Ignition switch ON Below 1.5 V
Idling 11 to 14 V
C50-87 (PRG) - C50-4 (E01) BR-Y - W-B No. 1 vacuum switching valve signal Idling, under purge control Pulse generation
(See waveform 14)
C50-100 (E2) - Body ground BR-W - - Ground circuit of ECM Always Below 1 Ω
C50-105 (E1) - Body ground W-B - - Ground circuit of ECM Always Below 1 Ω
C50-106 (KNK) - C50-100 (E2) L - BR-W Knock control sensor signal Engine speed maintained at 4000 rpm after warming up engine Pulse generation
(See waveform 15)

*1: w/o Resistor

*2: w/ Resistor

*3: for Manual Transmission

*4: w/ Engine Immobiliser System

*5: for Automatic Transmission

*6: The ECM terminal voltage is constant regardless of the output voltage from the sensor.

WAVEFORM 1


A361952E01
0.177,1.052 0.719,1.344 0.542,0.292 10 false GND 0.292,0.333 0.969,0.646 0.677,0.313 10 false 5 V/DIV. 1.583,1.74 2.594,2.094 1.01,0.354 10 false 20 msec./DIV.

Engine Speed Signal
ECM Terminal Name Between REV and E01
Tester Range 5 V/DIV., 20 msec./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 2


A292386E03
1.344,1.917 2.313,2.146 0.969,0.229 10 false 10 μsec./DIV. 2.76,0.219 3.333,0.427 0.573,0.208 10 false 1 V/DIV. 3,1.406 3.365,1.583 0.365,0.177 10 false GND

CAN Communication Signal (Reference)
ECM Terminal Name Between HCAN and E01, or CANH and E01
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 3


A292387E07
3,1.375 3.344,1.573 0.344,0.198 10 false GND 2.781,0.26 3.417,0.458 0.635,0.198 10 false 1 V/DIV. 1.375,1.885 2.323,2.135 0.948,0.25 10 false 10 μsec./DIV.

CAN Communication Signal (Reference)
ECM Terminal Name Between LCAN and E01, or CANL and E01
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 4


A208000E47
2.854,0.969 3.188,1.115 0.333,0.146 10 false GND 2.635,0.219 3.177,0.365 0.542,0.146 10 false 5 V/DIV. 0.5,0.615 0.719,0.76 0.219,0.146 10 false M+ 1.344,1.823 2.26,2.135 0.917,0.313 10 false 1 msec./DIV.

Throttle Actuator Positive Terminal Signal
ECM Terminal Name Between M+ and MR01
Tester Range 5 V/DIV., 1 msec./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



WAVEFORM 5


A245848E41
2.854,0.99 3.188,1.135 0.333,0.146 10 false GND 2.625,0.271 3.167,0.417 0.542,0.146 10 false 5 V/DIV. 0.479,0.625 0.667,0.771 0.188,0.146 10 false M- 1.323,1.823 2.26,2.104 0.938,0.281 10 false 1 msec./DIV.

Throttle Actuator Negative Terminal Signal
ECM Terminal Name Between M- and MR01
Tester Range 5 V/DIV., 1 msec./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



WAVEFORM 6


A205412E16
2.594,0.073 3.271,0.396 0.677,0.323 10 false 5 V/DIV. 2.698,0.896 3.188,1.198 0.49,0.302 10 false GND 1.156,1.844 2.365,2.125 1.208,0.281 10 false 10 msec./DIV.

Air Fuel Ratio Sensor Heater Signal
ECM Terminal Name Between AFM and AFHG
Tester Range 5 V/DIV., 10 msec./DIV.
Condition Idling

HINT:

The wavelength varies in accordance with the engine operating condition.



WAVEFORM 7


A292381E03
0.615,1.125 1.073,1.323 0.458,0.198 10 false GND 0.594,0.198 1.563,0.448 0.969,0.25 10 false 5 V/DIV. 1.76,1.854 2.719,2.135 0.958,0.281 10 false 1 msec./DIV.

Camshaft Timing Oil Control Valve (for Intake Camshaft) Signal
ECM Terminal Name Between OCV+ and OCV-
Tester Range 5 V/DIV., 1 msec./DIV.
Condition Idling with warm engine


WAVEFORM 8


A292381E03
0.615,1.125 1.073,1.323 0.458,0.198 10 false GND 0.594,0.198 1.563,0.448 0.969,0.25 10 false 5 V/DIV. 1.76,1.854 2.719,2.135 0.958,0.281 10 false 1 msec./DIV.

Camshaft Timing Oil Control Valve (for Exhaust Camshaft) Signal
ECM Terminal Name Between OCV2+ and OCV2-
Tester Range 5 V/DIV., 1 msec./DIV.
Condition Idling with warm engine


WAVEFORM 9


A141947E07
0.354,0.188 1.219,0.708 0.865,0.521 10 false 10 V/DIV. 0.292,1.469 0.854,1.865 0.563,0.396 10 false GND 1.646,1.854 2.542,2.146 0.896,0.292 10 false 2 msec./DIV.

Fuel Injector Signal
ECM Terminal Name Between #10 (to #40) and E01
Tester Range 10 V/DIV., 2 msec./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 10


A283571E07
0.51,0.219 1.292,0.521 0.781,0.302 10 false 0.2 V/DIV. 0.573,1.479 1.021,1.76 0.448,0.281 10 false GND 1.75,1.865 2.938,2.104 1.188,0.24 10 false 200 msec./DIV.

No. 2 Oxygen Sensor Signal
ECM Terminal Name Between OX and OX-
Tester Range 0.2 V/DIV., 200 msec./DIV.
Condition Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor

HINT:

In the Data List, the item O2S B1S2 shows the values input to the ECM from the No. 2 oxygen sensor.



WAVEFORM 11


A357520E01
0.271,0.115 0.938,0.458 0.667,0.344 10 false 2 V/DIV. 2.823,0.948 3.26,1.198 0.438,0.25 10 false GND 1.26,1.854 2.365,2.104 1.104,0.25 10 false 20 msec./DIV.

Ignition Coil Signal
ECM Terminal Name Between IG1 (to IG4) and E01
Tester Range 2 V/DIV., 20 msec./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 12


A200774E12
2.958,1.177 3.344,1.406 0.385,0.229 10 false GND 0.094,0.063 0.823,0.396 0.729,0.333 10 false 2 V/DIV. 1.219,1.875 2.344,2.115 1.125,0.24 10 false 5 msec./DIV.

Crankshaft Position Sensor Signal
ECM Terminal Name Between N and EN
Tester Range 2 V/DIV., 5 msec./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 13


A357521E01
0.135,0.115 0.823,0.396 0.688,0.281 10 false 5 V/DIV. 3.042,0.833 3.396,1.042 0.354,0.208 10 false GND 3.042,1.604 3.396,1.813 0.354,0.208 10 false GND 1.229,1.917 2.354,2.146 1.125,0.229 10 false 20 msec./DIV. 0.156,0.708 0.552,0.938 0.396,0.229 10 false CH1 0.167,1.51 0.563,1.74 0.396,0.229 10 false CH2

Camshaft Position Sensor Signal
ECM Terminal Name CH1: Between GIN and EGIN
CH2: Between GEX and EGEX
Tester Range 5 V/DIV., 20 msec./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 14


A287220E02
0.177,0.135 0.958,0.458 0.781,0.323 10 false 10 V/DIV. 0.24,1.354 0.698,1.677 0.458,0.323 10 false GND 1.563,1.729 2.667,2.073 1.104,0.344 10 false 20 msec./DIV.

No. 1 Vacuum Switching Valve Signal
ECM Terminal Name Between PRG and E01
Tester Range 10 V/DIV., 20 msec./DIV.
Condition Idling, under purge control

HINT:

If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.



WAVEFORM 15


A287225E02
0.198,0.385 0.927,0.854 0.729,0.469 10 false 1 V/DIV. 0.323,1.26 0.885,1.625 0.563,0.365 10 false GND 1.646,1.854 2.542,2.104 0.896,0.25 10 false 1 msec./DIV.

Knock Control Sensor Signal
ECM Terminal Name Between KNK and E2
Tester Range 1 V/DIV., 1 msec./DIV.
Condition Engine speed maintained at 4000 rpm after warming up engine

HINT:
·

The wavelength becomes shorter as the engine speed increases.

·

The waveforms and amplitudes displayed differ slightly depending on the vehicle condition.