DATA LIST
Using the GTS or Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Normal Condition: If no conditions are specifically stated for "idling", the shift lever should be in P or N, the A/C switch should be off and all accessory switches should be off.
Warm up the engine.
Turn the A/C switch off.
Turn the ignition switch off.
Connect the GTS or Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the GTS or Techstream on.
Enter the following menus: Powertrain / EFI / Data List.
According to the display on the GTS or Techstream, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Engine oil pressure SW | Engine oil pressure signal status | ON / OFF | ON: Engine running | - |
| Power steering oil pressure | Power steering signal status | ON / OFF | ON: Power steering operating | - |
| Stop lamp SW | Stop light switch signal status | ON / OFF | ·
ON: Brake pedal depressed ·
OFF: Brake pedal released |
- |
| Brake cancel SW | Stop light switch signal status | ON / OFF | ·
ON: Brake pedal depressed ·
OFF: Brake pedal released |
- |
| STA SW | Starter signal | ON / OFF | ·
ON: Starter operating ·
OFF: Starter not operating |
- |
| Electric load signal 1 | Electrical load signal | ON / OFF | - | - |
| Electric load signal 2 | Electrical load signal | ON / OFF | - | - |
| Electric load signal 3 | Electrical load signal | ON / OFF | - | - |
| Shift position P range | Park/neutral position switch status | ON / OFF | ·
ON: Shift lever in P ·
OFF: Shift lever not in P |
- |
| Shift position R range | Park/neutral position switch status | ON / OFF | ·
ON: Shift lever in R ·
OFF: Shift lever not in R |
- |
| Shift position N range | Park/neutral position switch status | ON / OFF | ·
ON: Shift lever in N ·
OFF: Shift lever not in N |
- |
| Shift position D range | Park/neutral position switch status | ON / OFF | ·
ON: Shift lever in D ·
OFF: Shift lever not in D |
- |
| Shift position 3 range | Park/neutral position switch status | ON / OFF | ·
ON: Shift lever in 3 ·
OFF: Shift lever not in 3 |
- |
| Shift position 2 range | Park/neutral position switch status | ON / OFF | ·
ON: Shift lever in 2 ·
OFF: Shift lever not in 2 |
- |
| Shift position L range | Park/neutral position switch status | ON / OFF | ·
ON: Shift lever in L ·
OFF: Shift lever not in L |
- |
| OD SW | Overdrive switch status | ON / OFF | ·
ON: Shift lever in 3 ·
OFF: Shift lever not in 3 |
- |
| Neutral start SW | Park/neutral position switch status | ON / OFF | ·
ON: Shift lever in P or N ·
OFF: Shift lever not in P or N |
- |
| AC SW | A/C switch status | ON / OFF | ON: A/C on | - |
| Test terminal | TC terminal status | ON / OFF | - | - |
| Purge VSV test | VSV status for EVAP control | ON / OFF | - | This parameter displays ON when EVAP (Purge) VSV is approximately 30% or higher, and displays OFF when the VSV duty ratio is less than 30%. |
| A/C magnet clutch relay test | Air conditioner magnet clutch status | ON / OFF | - | - |
| OCV test | Variable Valve Timing (VVT) control status | ON / OFF | - | ·
ON: The ECM is sending commands to change the timing (even when the timing is advanced, when the timing is being maintained and not being retarded or advanced any further, the value changes to OFF). ·
OFF: The system is commanding the timing to change to the most retarded timing. |
| Electrical fan test | Cooling fan motor operation status | ON / OFF | - | - |
| Purge VSV duty ratio | Purge VSV duty | Min.: 0%, Max.: 399.900% | - | - |
| A/F Heater Duty B1S1 | Air fuel ratio sensor heater duty ratio for bank 1 | Min.: 0%, Max.: 399.900% | 0 to 100% | When the value is any value except 0%, current is being supplied to the heater. |
| O2 Heater Curr Val B1S2 | No. 2 oxygen sensor current for bank 1 sensor 2 | Min.: 0 A, Max.: 4.990 A | - | When the value is any value except 0 A, current is being supplied to the heater. |
| O2 Heater B1S2 | No. 2 oxygen sensor heater for bank 1 sensor 2 | ON / OFF | - | - |
| Electrical fan high operation | Electric cooling fan high | ON / OFF | - | - |
| Electrical fan low operation | Electric cooling fan low | ON / OFF | - | - |
| Command throttle angle | Throttle position command value | Min.: 0 V Max.: 4.98 V | - | Command throttle angle is the same value as Request throttle angle. |
| +BM voltage | +BM voltage | Min.: 0 V Max.: 79.990 V | 11 to 14 V: Ignition switch ON and system normal | This is the power supply for the electronic throttle actuator. When the power supply is interrupted for approximately 1 second, DTCs P2118 (open circuit) and P0657 (short circuit, ECU malfunction) are stored and the electronic throttle control system enters fail-safe mode (normal operation is not restored until the ignition switch is turned off). |
| Main accelerator sensor voltage | No. 1 accelerator pedal position sensor voltage | Min.: 0 V Max.: 4.98 V | ·
0.5 to 1.1 V: Accelerator pedal fully released ·
2.6 to 4.5 V: Accelerator pedal fully depressed |
This is the raw voltage from the No. 1 accelerator pedal position sensor. |
| Sub accelerator sensor voltage | No. 2 accelerator pedal position sensor voltage | Min.: 0 V Max.: 4.98 V | ·
1.2 to 2.0 V: Accelerator pedal fully released ·
3.4 to 4.75 V: Accelerator pedal fully depressed |
This is the raw voltage from the No. 2 accelerator pedal position sensor. |
| Main throttle sensor voltage | No. 1 throttle position sensor output voltage | Min.: 0 V Max.: 4.98 V | Almost same as "Throttle Require Position"
·
0.5 to 1.1 V: Accelerator pedal fully released ·
3.2 to 4.8 V: Accelerator pedal fully depressed ·
0.6 to 1.4 V: Fail-safe operating |
This is the No. 1 throttle position sensor output voltage. |
| Sub throttle sensor voltage | No. 2 throttle position sensor output voltage | Min.: 0 V Max.: 4.98 V | ·
2.1 to 3.1 V: Accelerator pedal fully released ·
4.6 to 4.98 V: Accelerator pedal fully depressed ·
2.1 to 3.1 V: Fail-safe operating |
This is the No. 2 throttle position sensor output voltage. |
| Request throttle angle | Required throttle position | Min.: 0 V Max.: 4.98 V | 0.5 to 1.1 V: Idling (A/C off and shift lever in N) | This is a value calculated by the ECM showing the voltage for the target throttle valve position. It is almost an exact match of the Main throttle sensor voltage value except during very rapid throttle valve movement, such as that used during wheelspin control. |
| Throttle close learning value | Throttle valve fully closed position (learned value) | Min.: 0 V Max.: 4.98 V | 0.4 to 1.0 V: Accelerator pedal fully released | ·
The ECM uses this learned value to determine the fully closed (and fully open) position of the throttle valve. This learned value is calculated by the ECM with the throttle valve opener angle (approximately 4 to 7°, the position when the ignition switch is ON, the accelerator pedal is released and the throttle actuator is off). ·
Learning is performed immediately after the ignition switch is turned to ON. |
| Throttle motor open duty ratio | Throttle actuator duty ratio (open) | Min.: 0%, Max.: 255% | 0 to 40%: Idling (A/C off and shift lever in N) | This is the duty ratio used to drive the throttle actuator and open the throttle valve. It is an ECM command signal. |
| Throttle motor close duty ratio | Throttle actuator duty ratio (close) | Min.: 0%, Max.: 255% | 0 to 40%: Idling (A/C off and shift lever in N) | This is the duty ratio used to drive the throttle actuator and close the throttle valve. It is an ECM command signal.
|
| Throttle motor current | Throttle actuator current | Min.: 0 A Max.: 19.90 A | 0 to 3.0 A: Idling (A/C off and shift lever in N) | ·
When this value is large but the actual opening angle (Main throttle sensor voltage) does not reach the target opening angle (Request throttle angle), there is an "unable to open" malfunction. ·
This value normally fluctuates around 1 A. |
| ST1 input flag | Brake pedal signal | ON / OFF | ·
ON: Brake pedal depressed ·
OFF: Brake pedal released |
This is the stop light switch assembly signal (ST1- terminal). |
| #1 idle stabilization advance | Individual cylinder timing advance compensation amount (No. 1) | Min.: 0°CA, Max.: 15.90°CA | - | ·
This is the ignition timing advance compensation amount used to stabilize idling (each cylinder has a separate value). When the speed for a certain cylinder drops, the system advances the timing for that particular cylinder in an attempt to restore the speed and stabilize idling. ·
It may be possible to use this item to help determine specific cylinders which are not operating normally. |
| #2 idle stabilization advance | Individual cylinder timing advance compensation amount (No. 2) | Min.: 0°CA, Max.: 15.90°CA | - | ·
This is the ignition timing advance compensation amount used to stabilize idling (each cylinder has a separate value). When the speed for a certain cylinder drops, the system advances the timing for that particular cylinder in an attempt to restore the speed and stabilize idling. ·
It may be possible to use this item to help determine specific cylinders which are not operating normally. |
| #3 idle stabilization advance | Individual cylinder timing advance compensation amount (No. 3) | Min.: 0°CA, Max.: 15.90°CA | - | ·
This is the ignition timing advance compensation amount used to stabilize idling (each cylinder has a separate value). When the speed for a certain cylinder drops, the system advances the timing for that particular cylinder in an attempt to restore the speed and stabilize idling. ·
It may be possible to use this item to help determine specific cylinders which are not operating normally. |
| #4 idle stabilization advance | Individual cylinder timing advance compensation amount (No. 4) | Min.: 0°CA, Max.: 15.90°CA | - | ·
This is the ignition timing advance compensation amount used to stabilize idling (each cylinder has a separate value). When the speed for a certain cylinder drops, the system advances the timing for that particular cylinder in an attempt to restore the speed and stabilize idling. ·
It may be possible to use this item to help determine specific cylinders which are not operating normally. |
| Stored minimum engine speed | Minimum engine speed | Min.: 0 rpm, Max.: 51199.2 rpm | - | ·
This is the lowest engine speed detected throughout the trip after the engine is started and ISC learning is completed. ·
For use when engine stall, starting problems or rough idle is present. |
| Stall avoidance correction value | Intake air compensation flow rate | Min.: -40 L/s, Max.: 39.998 L/s | - | ·
The intake air amount and ignition timing are adjusted when there is a large decrease in engine speed (for example, a decrease to 550 rpm or less) in order to prevent engine stall. ·
For use when engine stall, starting problems or rough idle is present. |
| Amount of deposit air loss | Flow loss due to deposits | Min.: -40 L/s, Max.: 39.998 L/s | - | This value indicates the amount of compensation for a decrease in intake airflow due to the buildup of deposits on the throttle valve.
This value is updated after a long period of time. For use when engine stall, starting problems or rough idle is present. |
| Time after high revolution | Elapsed time since fuel cut due to high engine speed | Min.: 0 s, Max.: 68746.2 s | - | - |
| Throttle chara. learn val zone0 | Throttle air flow learning value of area 0 | Min.: 0 times, Max.: 1.999 times | - | - |
| Throttle chara. learn val zone1 | Throttle air flow learning value of area 1 | Min.: 0 times, Max.: 1.999 times | - | - |
| Throttle chara. learn val zone2 | Throttle air flow learning value of area 2 | Min.: 0 times, Max.: 1.999 times | - | - |
| Throttle chara. anneal value | Throttle air flow learning value (calculated value) | Min.: 0 times, Max.: 1.999 times | - | - |
| Throttle barometric correction | Throttle air flow learning value (atmosphere pressure offset value) | Min.: 0 times, Max.: 2.55 times | - | - |
| Throttle learn veto in. pressure | Throttle air flow learning prohibit (intake air pressure malfunction) | ON / OFF | - | - |
| Throttle learn veto air/fuel | Throttle air flow learning prohibit (air fuel ratio malfunction) | ON / OFF | - | - |
| Stop cylinder engine speed #1 | Engine speed for cylinder No. 1 | Min.: 0 rpm, Max.: 51199.2 rpm | - | ·
This is output only when Check the Cylinder Compression is performed using the Active Test. ·
This is the engine speed for each cylinder measured during the fuel-cut with the engine cranking. ·
When there is compression loss, the engine speed for that cylinder increases.
|
| Stop cylinder engine speed #2 | Engine speed for cylinder No. 2 | Min.: 0 rpm, Max.: 51199.2 rpm | - | ·
This is output only when Check the Cylinder Compression is performed using the Active Test. ·
This is the engine speed for each cylinder measured during the fuel-cut with the engine cranking. ·
When there is compression loss, the engine speed for that cylinder increases.
|
| Stop cylinder engine speed #3 | Engine speed for cylinder No. 3 | Min.: 0 rpm, Max.: 51199.2 rpm | - | ·
This is output only when Check the Cylinder Compression is performed using the Active Test. ·
This is the engine speed for each cylinder measured during the fuel-cut with the engine cranking. ·
When there is compression loss, the engine speed for that cylinder increases.
|
| Stop cylinder engine speed #4 | Engine speed for cylinder No. 4 | Min.: 0 rpm, Max.: 51199.2 rpm | - | ·
This is output only when Check the Cylinder Compression is performed using the Active Test. ·
This is the engine speed for each cylinder measured during the fuel-cut with the engine cranking. ·
When there is compression loss, the engine speed for that cylinder increases.
|
| All cyl. average engine speed | Average engine speed for all cylinders | Min.: 0 rpm, Max.: 51199.2 rpm | - | This is output only when Check the Cylinder Compression is performed using the Active Test. |
| A/F learning value(idle) | Air fuel ratio learned value for idling | Min.: -50%, Max.: 49.6% | - | Learning is performed when idling with the engine warmed up (engine coolant temperature is 80°C (176°F) or higher). |
| A/F learning value(low load) | Air fuel ratio learned value for low engine loads | Min.: -50%, Max.: 49.6% | - | Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C (176°F) or higher) and operating in the low load range (when the range of engine loads is divided into five parts). |
| A/F learning value(mid. load1) | Air fuel ratio learned value for mid-sized engine loads 1 | Min.: -50%, Max.: 49.6% | - | Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C (176°F) or higher) and operating in the mid-size load range closer to the low load range (when the range of engine loads is divided into five parts). |
| A/F learning value(mid. load2) | Air fuel ratio learned value for mid-sized engine loads 2 | Min.: -50%, Max.: 49.6% | - | Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C (176°F) or higher) and operating in the mid-size load range closer to the high and low load range (when the range of engine loads is divided into five parts). |
| A/F learning value(high load) | Air fuel ratio learned value for high engine loads | Min.: -50%, Max.: 49.6% | - | Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C (176°F) or higher) and operating in the high load range (when the range of engine loads is divided into five parts). |
| Number of diagnosis codes | Number of codes | Min.: 0, Max.: 255 | 0 | - |
| Number of all diagnosis codes | Number of all codes | Min.: 0, Max.: 255 | 0 | - |
| Key Cycle | Number of trips | Min.: 0, Max.: 65535 | - | - |
| Original count identification | Original count identification | Normal / IG sys / ACC sys / +B sys | - | - |
| IG-ON Elapsed Time | Time after ignition switch ON | Min.: 0 s, Max.: 1677721.5 s | - | - |
| Check mode | Check mode | ON / OFF | - | - |
| ECT at engine start | Initial engine coolant temperature | Min.: -40°C, Max.: 119.3°C | - | This is the engine coolant temperature stored when the ignition switch is turned to ON. |
| IAT at engine start | Initial intake air temperature | Min.: -40°C, Max.: 119.3°C | - | This is the intake air temperature stored when the ignition switch is turned to ON. |
| Knock corr. learning value | Knocking correction learned value | Min.: -1024°CA, Max.: 1023.96°CA | - | ·
Refer to "Knock control value". ·
When there is knocking or a lack of power, compare the following values to another vehicle of the same model. ·
Engine revolution speed ·
Calculated load value ·
Ignition timing advance No.1 ·
Knock control value ·
Knock corr. learning value ·
Knock corr. learning value is large: There is no knocking and the ignition timing is advanced. ·
Knock corr. learning value is small: Knocking is present and the ignition timing is being retarded.
|
| Knock control value | Knocking feedback value | Min.: -1024°CA, Max.: 1023.96°CA | - | This is the ignition timing retard compensation amount determined by the presence or absence of knocking.
Ignition timing = Most retarded timing value*1 + Knock corr. learning value*2 + Knock control value*3 + each compensation amount Example: 21°CA = 10°CA + 14°CA - 3°CA *1: The most retarded timing value is a constant determined by the engine speed and engine load. *2: The Knock corr. learning value is calculated as shown below in order to keep Knock control value as close to -3°CA as possible. When Knock control value is less than -4°CA, Knock corr. learning value is slowly decreased. When Knock control value is higher than -2°CA, Knock corr. learning value is slowly increased. *3: The base value is -3°CA and is adjusted based on the presence or absence of knocking. When there is no knocking, the value is increased, and when knocking is present, the value is decreased. -1°CA: There is no knocking and ignition timing is advanced. -6°CA: Knocking is present and the ignition timing is being retarded.
|
| Purge learning value | Purge density learned value | Min.: -200%/%, Max.: 199.993%/% | - | ·
Purge learning value is the proportion of the decrease in injection volume (based on the change in the air fuel ratio feedback compensation value) related to a 1% purge flow rate. ·
When Purge learning value is a large negative value, the purge effect is large. ·
The purge density is determined from the change in the air fuel ratio feedback compensation value when purge flow is introduced. ·
Purge density learning is performed so that the feedback compensation value is 0 +/-2%.
|
| Purge percentage | Purge flow | Min.: 0%, Max.: 399.993% | - | ·
This is the percentage of total engine airflow contributed by EVAP purge operation. (Purge percentage = Purge flow / Engine airflow x 100 (%)) ·
It is based on Air flow rate and a stored value for airflow and controlled by adjusting the duty cycle for the purge VSV. |
| Distance after battery OFF | Distance driven after battery cable disconnected | Min.: 0 km, Max.: 65535 km | Total distance vehicle driven after battery cable disconnected | - |
| F/C flag | Fuel cut condition | ON / OFF | ON: Fuel cut operating | - |
| Idling flag | Closed throttle position switch status | ON / OFF | ·
ON: Throttle fully closed ·
OFF: Throttle open |
- |
| Idling ON F/C flag | Fuel cut at idle | ON / OFF | ON: Fuel cut operating | Idling ON F/C flag = "ON" when the throttle valve is fully closed and the engine speed is high. |
| Light load F/C flag | Fuel cut TAU (fuel cut during very light load) | ON / OFF | ON: Fuel cut operating | This is the fuel cut performed under a very light load to prevent the engine combustion from becoming incomplete. |
| Crank signal count | Cranking signal count | Min.: 0 times, Max.: 255 times | - | - |
| First combustion time | First combustion time | Min.: 0 ms, Max.: 16711.6 ms | - | - |
| Initial peak RPM time | Time of initial peak engine speed | Min.: 0 ms, Max.: 16711.6 ms | - | - |
| Initial peak RPM | Initial peak engine speed | Min.: 0 rpm, Max.: 2550 rpm | - | - |
| IG-ON elapsed time | Time after ignition switch ON | Min.: 0 ms, Max.: 4177.9 ms | - | - |
| Average engine speed | Average engine speed | Min.: 0 rpm, Max.: 6375 rpm | - | - |
| Max vehicle speed | Maximum vehicle speed | Min.: 0 km/h, Max.: 255 km/h | - | - |
| Average vehicle speed | Average vehicle speed | Min.: 0 km/h, Max.: 255 km/h | - | - |
| Initial engine coolant temp | Initial engine coolant temperature | Min.: -40°C, Max.: 119.3°C | - | - |
| Trip at BOS operation | Trip at brake override system operation | Min.: 0 times, Max.: 65535 times | - | - |
| Trip counter at overheat | Trip counter at overheat | Min.: 0 times, Max.: 65535 times | - | - |
| Brake vacuum SW | Brake pressure switch signal | ON / OFF | - | - |
| A/C evap temperature | A/C evap temperature | Min.: 0°C, Max.: 1023.98°C | Approximately the same temperature as the vehicle cabin. Internal ventilation, MAX COOL, air conditioning is off and blower is on. | - |
| A/C refrigerant pressure | A/C refrigerant pressure | Min.: 0 MPa, Max.: 1023.98 MPa | 0 MPa (0 kgf/cm2) to 3.18 MPa (32.4 kgf/cm2): Ignition switch ON | - |
| Injection volume | Injection volume (cylinder 1) | Min.: 0 ml Max.: 2.047 ml | 0 to 0.15 ml: Idling | This is the fuel injection volume for 10 injections. |
| Injection time | Injection period of the No. 1 cylinder | Min.: 0 μs Max.: 65535 μs | - | This is the injection period of the No. 1 cylinder (the command value from the ECM). |
| DVVT keep duty learning value | VVT hold duty learned value for bank 1 | Min.: 0%, Max.: 399.993% | - | This value represents the duty ratio necessary to operate the camshaft timing oil control valve assembly in order to block the camshaft timing oil control valve assembly path and maintain the advanced state of the VVT controller. |
| DVVT OCV duty learning value | VVT camshaft timing oil control valve operation duty for bank 1 | Min.: 0%, Max.: 399.993% | - | - |
| DVVT actual angle | VVT displacement angle for bank 1 | Min.: 0°FR, Max.: 639.990°FR | - | By checking DVVT actual angle during the Active Test, it is also possible to determine whether or not the camshaft position sensor signal is being output. |
| EX.DVVT keep duty learning value | VVT exhaust hold duty ratio learned value for bank 1 | Min.: 0%, Max.: 399.993% | - | This value represents the duty ratio necessary to operate the camshaft timing oil control valve assembly in order to block the camshaft timing oil control valve assembly path and maintain the retarded state of the VVT controller. |
| EX.DVVT OCV duty learning value | VVT exhaust camshaft timing oil control valve duty for bank 1 | Min.: 0%, Max.: 399.993% | - | - |
| EX.DVVT actual angle | VVT exhaust displacement angle for bank 1 | Min.: 0°FR, Max.: 639.990°FR | - | - |
| Average engine speed at misfiring | Engine speed for first misfire range | Min.: 0 rpm, Max.: 6375 rpm | 0 rpm: 0 misfires | ·
This is the average engine speed recorded when misfiring occurs. ·
This value is closer to the actual conditions of the vehicle at the time misfire occurred than the values of engine speed and engine load stored in the freeze frame data. When reproducing malfunction conditions, use this value as a reference. |
| Average load at misfiring | Engine load for first misfire range | Min.: 0 g/rev, Max.: 3.98 g/rev | 0 g/rev: 0 misfires | ·
This is the average engine load recorded when misfiring occurs. ·
This value is closer to the actual conditions of the vehicle at the time misfire occurred than the values of engine speed and engine load stored in the freeze frame data. When reproducing malfunction conditions, use this value as a reference.
|
| Cylinder #1 misfire count | Misfire count of cylinder 1 | Min.: 0 times, Max.: 255 times | 0 | ·
This is the misfire count for each individual cylinder. ·
This counter is increased by one for each misfire and is cleared every 200 revolutions. ·
Check this item to help determine the malfunctioning cylinder. |
| Cylinder #2 misfire count | Misfire count of cylinder 2 | Min.: 0 times, Max.: 255 times | 0 | ·
This is the misfire count for each individual cylinder. ·
This counter is increased by one for each misfire and is cleared every 200 revolutions. ·
Check this item to help determine the malfunctioning cylinder. |
| Cylinder #3 misfire count | Misfire count of cylinder 3 | Min.: 0 times, Max.: 255 times | 0 | ·
This is the misfire count for each individual cylinder. ·
This counter is increased by one for each misfire and is cleared every 200 revolutions. ·
Check this item to help determine the malfunctioning cylinder. |
| Cylinder #4 misfire count | Misfire count of cylinder 4 | Min.: 0 times, Max.: 255 times | 0 | ·
This is the misfire count for each individual cylinder. ·
This counter is increased by one for each misfire and is cleared every 200 revolutions. ·
Check this item to help determine the malfunctioning cylinder. |
| All cylinder misfire count | Misfire count of all cylinders | Min.: 0 times, Max.: 255 times | 0 to 35 | ·
This is the total misfire count of all cylinders. ·
This counter is increased by one for each misfire, has a maximum value of 255 and is cleared every 1000 revolutions. |
| Misfire count parameter | Ignition counter | Min.: 0, Max.: 65535 | 0 to 400 | ·
This is the cumulative number of ignitions. ·
This counter is incremented by one for each ignition (this stops when misfire monitoring stops). This value is cleared every 200 revolutions. ·
The misfire rate for each cylinder is calculated by dividing the misfire count for each cylinder by Misfire count parameter. ·
The misfire rate for each cylinder = Cylinder #1 to #4 misfire Count / Misfire count parameter
|
| Margin of misfire ratio monitor | Misfire monitoring | Min.: -128%, Max.: 127% | 0 to 127%: Idling | ·
This is the misfire detection margin. ·
Margin of misfire ratio monitor = (Misfire detection threshold - maximum engine speed variation) / misfire detection threshold x 100% ·
When the variation in the engine speed is large and exceeds the misfire detection threshold, the misfire count starts. Margin of misfire ratio monitor is a measure of how much the engine speed variation can increase with respect to the threshold before the engine is determined to be misfiring. ·
A large value means there is a large margin for the engine speed to vary before the engine is determined to be misfiring. ·
Example: When the engine is determined to be misfiring, Margin of misfire ratio monitor = -128 to 0%. |
| Engine starting time | Time elapsed before engine starts (after starter turns on until engine speed reaches 400 rpm) | Min.: 0 ms, Max.: 655350 ms | - | ·
This is the time elapsed after the starter turns on until the engine speed reaches 400 rpm. ·
This value is cleared 5 seconds after the engine is started and the value is displayed as 0 ms. |
| Engine speed (starter OFF) | Engine speed when starter off | Min.: 0 rpm, Max.: 51199.2 rpm | - | This is the engine speed immediately after starting the engine. |
| Starter count | Number of times starter turned on after ignition switch turned to ON | Min.: 0 times, Max.: 255 times | - | ·
Indicates the number of times starter turned on in the current driving cycle. ·
Number of times starter turned on before engine started displayed in the 1 position. ·
Number of times starter turned on after engine started displayed in the 10 position. Example: If "21" is displayed on the GTS or Techstream, the starter was turned on 1 time before engine start and turned on 2 times after engine start. (The maximum value for each counter is 9 times before engine start and 11 times after engine start) |
| Run distance of previous trip | Distance driven during previous trip | Min.: 0 km, Max.: 655.35 km | - | ·
Before 5 seconds elapse after starting the engine, which is the detection duration of DTC P1604 (Startability Malfunction), this parameter indicates the distance driven during the previous trip. ·
After 5 seconds elapse after starting the engine, this parameter indicates the distance driven during the current trip calculated from the vehicle speed signal.
|
| Stored coolant temperature | Engine coolant temperature during previous trip | Min.: -40°C, Max.: 215°C | - | ·
Before 120 seconds elapse after starting the engine, this parameter indicates the engine coolant temperature at the end of the previous trip. ·
After 120 seconds elapse after starting the engine, this parameter indicates the engine coolant temperature during the current trip. |
| Stored intake air temperature | Intake air temperature during previous trip | Min.: -40°C, Max.: 215°C | - | ·
Before 120 seconds elapse after starting the engine, this parameter indicates the intake air temperature at the end of the previous trip. ·
After 120 seconds elapse after starting the engine, this parameter indicates the intake air temperature during the current trip. |
| Throttle opening angle | Throttle valve opening angle | Min.: 0°, Max.: 499.992° | - | This value has no meaning when the ignition switch is ON and the engine is stopped. |
| ISC opening angle | Requested throttle opening amount calculated using ISC control | Min.: 0°, Max.: 499.992° | - | This is the throttle valve opening amount while the engine is idling (the throttle valve opening amount necessary to maintain ISC air flow). |
| N/D flag | Shift lever N status | P or N / Except P,N | ON: Shift lever is P or N | - |
| Eng. speed decrease control flag | Low engine speed control operation state | ON / OFF | - | ·
This parameter indicates whether the engine speed dropped immediately after starting due to poor combustion, etc. This parameter changes to ON when the engine speed drops to below the following speeds 1 to 7 seconds after the engine is started (when the A/C is on, the engine speed thresholds below increase by 100 to 200 rpm). ·
900 rpm (when the engine coolant temperature is 10°C (50°F)) ·
850 rpm (when the engine coolant temperature is 30°C (86°F)) ·
750 rpm (when the engine coolant temperature is 60°C (140°F)) Before 5 seconds elapse after starting the engine, this parameter indicates the status of the previous trip. After 5 seconds elapse after starting the engine, this parameter indicates the status of the current trip.
·
For use when engine stall, starting problems or rough idle is present. |
| DVVT advance fail flag | VVT control failure status | ON / OFF | OFF | ON: There is a VVT timing advance malfunction. |
| Low rev for engine start | History of low engine speed after engine start | ON / OFF | - | This item changes to ON when the engine speed drops to 200 rpm or less within approximately 2 seconds of starting the engine. |
| Engine start hesitation | History of hesitation during engine start | ON / OFF | - | This value changes to ON when the engine speed does not reach 500 rpm during cranking. |
| Immobilizer fuel cut flag | Status of immobiliser fuel cut | ON / OFF | - | - |
| Immobilizer F/C history flag | Immobiliser fuel cut history | ON / OFF | OFF | When DTC P1604 is output and Immobilizer F/C history flag indicates ON, the engine could not start due to engine immobiliser operation. |
| Calculated load value | Load calculated by ECM | Min.: 0%, Max.: 100.0% | - | ·
This is the engine load calculated based on the estimated intake manifold pressure. ·
Calculated load value = Estimated intake manifold pressure / maximum intake manifold pressure x 100 (%) (For example, when the estimated intake manifold pressure is the same as atmospheric pressure, Calculated load value is 100%.) |
| Air flow rate | Airflow rate from intake air flow meter assembly | Min.: 0 g/s, Max.: 655.35 g/s | ·
1.0 to 3.0 g/s: Idling with warm engine (A/C off and shift lever in N) ·
3.0 to 8.0 g/s: 3000 rpm (A/C off and shift lever in N) |
This is the intake air amount from the intake air flow meter assembly. |
| Intake air temperature | Intake air temperature | Min.: -40°C, Max.: 215°C | Equivalent to temperature at location of intake air flow meter assembly | This is the intake air temperature.
|
| Barometric pressure | Atmospheric pressure | Min.: 0 kPa, Max.: 255 kPa | Equivalent to atmospheric pressure (absolute pressure) | ·
This value is calculated from the intake air amount. ·
Standard atmospheric pressure: 101 kPa (758 mmHg) ·
For every 100 m (328 ft) increase in altitude, pressure drops by 1 kPa (7.5 mmHg). This varies by weather. |
| Engine coolant temperature | Engine coolant temperature | Min.: -40°C, Max.: 215°C | 75 to 100°C (167 to 212°F): After warming up engine | This is the engine coolant temperature.
|
| Engine revolution speed | Engine speed | Min.: 0 rpm, Max.: 16383.7 rpm | 550 to 650 rpm (for Manual Transmission):
650 to 750 rpm (for Automatic Transmission): Idling with warm engine, shift lever in N, A/C off |
When the crankshaft position sensor is malfunctioning, "Engine revolution speed" is approximately 0 rpm or varies greatly from the actual engine speed. |
| Vehicle speed | Vehicle speed | Min.: 0 km/h, Max.: 255 km/h | Actual vehicle speed | ·
This is the current vehicle speed. ·
The vehicle speed is detected using the wheel speed sensors. ·
There is a delay in when the vehicle speed data is displayed. Therefore, even if the vehicle speed listed in the freeze frame data is 0 km/h (0 mph), this does not always mean that the malfunction occurred when the vehicle was stopped. |
| Time after engine starting | Engine run time | Min.: 0 s, Max.: 65535 s | Time after engine start | This is the time elapsed since the engine was started.
|
| Relative throttle position | Throttle sensor position | Min.: 0%, Max.: 100.0% | ·
0%: Accelerator pedal fully released ·
50 to 80%: Accelerator pedal fully depressed |
·
This is the throttle valve opening amount used for engine control. (100% signifies 125° of throttle valve rotation. This does not include the amount the throttle valve is opened to maintain the idle speed during idling.) ·
This value has no meaning when the ignition switch is ON and the engine is stopped. |
| Main throttle position | Absolute No. 1 throttle position sensor | Min.: 0%, Max.: 100.0% | ·
10 to 22%: Accelerator pedal fully released ·
64 to 96%: Accelerator pedal fully depressed |
The No. 1 throttle position sensor output is converted using 5 V = 100%.
|
| Sub throttle position | Absolute No. 2 throttle position sensor | Min.: 0%, Max.: 100.0% | ·
42 to 62%: Accelerator pedal fully released ·
92 to 100%: Accelerator pedal fully depressed |
The No. 2 throttle position sensor output is converted using 5 V = 100%. |
| Main accelerator position | Absolute No. 1 accelerator pedal position | Min.: 0%, Max.: 100.0% | ·
10 to 22%: Accelerator pedal fully released ·
52 to 90%: Accelerator pedal fully depressed |
The No. 1 accelerator pedal sensor output is converted using 5 V = 100%.
|
| Sub accelerator position | Absolute No. 2 accelerator pedal position | Min.: 0%, Max.: 100.0% | ·
24 to 40%: Accelerator pedal fully released ·
68 to 95%: Accelerator pedal fully depressed |
The No. 2 accelerator pedal sensor output is converted using 5 V = 100%. |
| Target throttle position | Throttle actuator | Min.: 0%, Max.: 100.0% | 0 to 40%: Idling (A/C off and shift lever in N) | This is the output duty ratio of the throttle actuator drive circuit. |
| Warm-up cycle cleared DTC | Warmup cycles after DTCs cleared | Min.: 0 times, Max.: 255 times | - | ·
This is the number of warmup cycles after the DTCs were cleared. ·
This is the number of times the engine was warmed up* after DTCs were cleared (or after the vehicle left the factory). *: An engine warmup is defined as the engine coolant temperature rising 20°C (68°F) or higher and reaching a temperature of 70°C (158°F) or higher after the engine is started. |
| Distance from DTC cleared | Distance driven after DTCs cleared | Min.: 0 km, Max.: 65535 km | Distance driven after DTCs cleared | This is the distance driven since DTCs were cleared (or since the vehicle left the factory). |
| Time after DTC cleared | Time after DTCs cleared | Min.: 0 min, Max.: 65535 min | Time after DTCs cleared | This is the time elapsed since DTCs were cleared (or since the vehicle left the factory). Time elapsed since the ignition switch is turned off is not counted. |
| Battery voltage | Battery voltage | Min.: 0 V, Max.: 65.535 V | 11 to 14 V: Idling | If 11 V or less, characteristics of some electrical components may change. |
| Fuel system sutatus bank1 | Fuel system status for bank 1 | - / OL / CL / OL-Drv / OL-Flt / CL-Flt | CL: Idling after warming up | ·
OL (Open Loop): Has not yet satisfied conditions to go to closed loop. ·
CL (Closed Loop): Feedback to perform fuel control. ·
OL-Drv: Open loop due to driving conditions (fuel enrichment). ·
OL-Flt: Open loop due to a detected system fault. ·
CL-Flt: Closed loop but the air fuel ratio sensor, which is used for fuel control, is malfunctioning. |
| Fuel system sutatus bank2 | Fuel system status for bank 2 | - / OL / CL / OL-Drv / OL-Flt / CL-Flt | Unused | - |
| Short term fuel trim bank 1 | Short-term fuel trim for bank 1 | Min.: -100%, Max.: 99.2% | -15 to 15% | This item is the "short-term fuel injection volume compensation ratio" used to maintain the air fuel ratio at the stoichiometric ratio using the air fuel ratio sensor for feedback. |
| Long term fuel trim bank 1 | Long-term fuel trim for bank 1 | Min.: -100%, Max.: 99.2% | -15 to 15% | ·
The ECM will learn the Long term fuel trim bank 1 values based on Short term fuel trim bank 1. The goal is to keep Short term fuel trim bank 1 at 0% to keep the air fuel ratio mixture at the stoichiometric ratio. ·
This value is used to determine whether the system related to air fuel ratio control is malfunctioning. ·
The condition of the system is determined based on the sum of Short term fuel trim bank 1 and Long term fuel trim bank 1 (excluding times when the system is in transition). ·
15% or higher: There may be a lean air fuel ratio. ·
-15 to 15%: The air fuel ratio can be determined to be normal. ·
-15% or less: There may be a rich air fuel ratio. ·
Air fuel ratio feedback learning is divided up according to the engine operating range (engine speed x load), and a separate value is stored for each operating range. "Long term fuel trim bank 1" indicates the learned value for the current operating range. |
| Ignition timing advance No.1 | Ignition timing advance for No. 1 cylinder | Min.: -64°, Max.: 63.5° | -10 to 10 deg: Idling with warm engine (A/C off and shift lever in N) | - |
| Taget air fuel ratio | Target air fuel ratio | Min.: 0, Max.: 1.999 | 0.8 to 1.2: During idling | ·
This is the target air fuel ratio used by the ECM. ·
1.0 is the stoichiometric air fuel ratio. Values that are more than 1.0 indicate the system attempting to make the air fuel ratio leaner. Values that are less than 1.0 indicate the system attempting to make the air fuel ratio richer. ·
Target Air-Fuel Ratio and AF Lambda B1S1 are related. |
| AF Lambda B1S1 | Output air fuel ratio associated with bank 1 sensor 1 | Min.: 0, Max.: 1.999 | Value less than 1 (0.000 to 0.999) = Rich 1 = Stoichiometric air fuel ratio Value more than 1 (1.001 to 1.999) = Lean | ·
This is the actual air fuel ratio calculated based on the air fuel ratio sensor output. ·
Performing the "Control the Injection Volume" function of the Active Test enables the technician to check the voltage output of the sensor. |
| AFS Voltage B1S1 | Air fuel ratio sensor output voltage for bank 1 sensor 1 | Min.: 0 V, Max.: 7.999 V | 2.6 to 3.8 V: Idling | ·
This is the voltage output of the air fuel ratio sensor (the voltage cannot be measured at the terminals of the sensor). This value is calculated by the ECM based on the current output of the air fuel ratio sensor (refer to AFS Current B1S1 below for the actual sensor output). ·
Performing the "Control the Injection Volume" function of the Active Test enables the technician to check the voltage output of the sensor. |
| AFS Current B1S1 | Air fuel ratio sensor output current for bank 1 sensor 1 | Min.: -128 mA, Max.: 127.996 mA | -0.5 to 0.5 mA: Idling | ·
With a stoichiometric air fuel ratio (for example, during idling after the engine is warmed up), the air fuel ratio sensor current output is approximately -0.5 to 0.5 mA. ·
When the value is outside the range of 0.7 to 2.2 mA when the fuel-cut is being performed, there is a malfunction in the air fuel ratio sensor or sensor circuit. |
| O2S B1S2 | No. 2 oxygen sensor output voltage | Min.: 0 V, Max.: 1.275 V | 0 to 1 V | This is the output voltage of the No. 2 oxygen sensor. |
| Catalyst Temp B1S1 | Catalyst temperature for bank 1 sensor 1 | Min.: -40°C (-40°F), Max.: 6513.5°C (11756.3°F) | - | ·
This is the temperature of the front catalyst estimated by the ECM. ·
This value is included in the conditions used to detect catalyst deterioration (DTC P0420), etc., and should therefore be used as a reference when recreating malfunction conditions. |
| Catalyst Temp B1S2 | Catalyst temperature for bank 1 sensor 2 | Min.: -40°C (-40°F), Max.: 6513.5°C (11756.3°F) | - | This is the temperature of the rear catalyst estimated by the ECM. |
| MIL status | MIL status | ON / OFF | OFF | - |
| Comprehensive component Support | Comprehensive component monitor | Avail / Not Avi | - | ·
* |
| Fuel system Support | Fuel system monitor | Avail / Not Avi | - | ·
* |
| Misfire monitoring | Misfire monitor | Avail / Not Avi | - | ·
* |
| EGR/VVT system Support | EGR/VVT monitor | Avail / Not Avi | - | ·
* |
| Oxygen sensor heater Support | O2S (A/FS) heater monitor | Avail / Not Avi | - | ·
* |
| Oxygen sensor Support | O2S (A/FS) monitor | Avail / Not Avi | - | ·
* |
| A/C system refrigerant Support | A/C monitor | Avail / Not Avi | - | ·
* |
| Secondary air system Support | 2nd air monitor | Avail / Not Avi | - | ·
* |
| Evaporative system Support | EVAP monitor | Avail / Not Avi | - | ·
* |
| Heated catalyst system Support | Heated catalyst monitor | Avail / Not Avi | - | ·
* |
| Catalyst Support | Catalyst monitor | Avail / Not Avi | - | ·
* |
| EGR/VVT system monitoring | EGR/VVT monitor | Incompl / Compl | - | ·
* |
| Oxygen sensor heater monitoring | O2S (A/FS) heater monitor | Incompl / Compl | - | ·
* |
| Oxygen sensor monitoring | O2S (A/FS) monitor | Incompl / Compl | - | ·
* |
| A/C system refrigerant monitoring | A/C monitor | Incompl / Compl | - | ·
* |
| Secondary air system monitoring | 2nd air monitor | Incompl / Compl | - | ·
* |
| Evaporative system monitoring | EVAP monitor | Incompl / Compl | - | ·
* |
| Heated catalyst system monitoring | Heated catalyst monitor | Incompl / Compl | - | ·
* |
| Catalyst monitoring | Catalyst monitor | Incompl / Compl | - | ·
* |
| Distance after MIL ON | Distance driven with MIL on | Min.: 0 km, Max.: 65535 km | - | This is the distance driven since the MIL was illuminated. |
| Time after MIL ON | Running time from MIL on | Min.: 0 min, Max.: 65535 min | Running time after MIL turned on | - |
*:
Avail: The monitor is available on the vehicle.
Not Avl: The monitor is not available on the vehicle.
Incmpl / Compl: The item changes from Incmpl to Compl if the monitor was completed at least once at some time in the past. This item does not change when the ignition switch is turned off. However, the item changes back to Incmpl when DTCs are cleared or the battery cable is disconnected.
ACTIVE TEST
Using the GTS or Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS or Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the GTS or Techstream on.
Enter the following menus: Powertrain / EFI / Active Test.
According to the display on the GTS or Techstream, perform the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Injection volume | Control the injection volume | Between -12.5% and 24.8% | ·
All fuel injector assemblies are tested at the same time. ·
Perform the test at 3000 rpm or less. ·
Injection volume can be changed in fine gradations within the control range. ·
Control the Injection Volume enables the checking of the air fuel ratio sensor and No. 2 oxygen sensor voltage outputs. |
| Purge VSV | Activate purge VSV control | 0%/100% | The purge VSV is opened with a approximately 30% duty ratio. |
| A/C magnet clutch relay | Control air conditioner magnet clutch | ON/OFF | - |
| DVVT | Activate VVT system | ON/OFF | - |
| Terminal T | Turn on and off T and E connection | ON/OFF | ·
ON: T and E terminals of DLC3 are connected. ·
OFF: T and E terminals of DLC3 are disconnected. |
| Idle fuel cut prohibit | Prohibit idling fuel cut control | ON/OFF | - |
| Radiator fan | Control electric cooling fan motor | ON/OFF | - |
| Air-bleeding for fuel return less | Control fuel pump air bleeding | Between 0.1 to 25.5 | - |
| Throttle valve (slow) | Throttle actuator | Close/Open
Open: Throttle valve opens slowly |
- |
| Throttle valve (fast) | Throttle actuator | Close/Open
Open: Throttle valve opens quickly |
- |
| Select Cylinder Fuel Cut | Selected cylinder (cylinder #1 to #4) injector fuel cut | #1/#2/#3/#4
ON/OFF |
- |
| All cylinders fuel cut | Fuel cut for all cylinders | ON/OFF | - |
| Check the Cylinder Compression | Check the cylinder compression pressure | ON/OFF | Fuel injection and ignition stop of all cylinders. |
| IN.DVVT Linear | Control camshaft timing oil control valve assembly (for intake camshaft) | -128 to 127% (This value added to present camshaft timing oil control valve control duty)
100%: Maximum advance -100%: Maximum retard |
Engine stalls or idles roughly when the camshaft timing oil control valve assembly (for intake camshaft) is set to 100%. |
| EX.DVVT Linear | Control camshaft timing oil control valve assembly (for exhaust camshaft) | -128 to 127% (This value added to present camshaft timing oil control valve control duty)
100%: Maximum retard -100%: Maximum advance |
Engine stalls or idles roughly when the camshaft timing oil control valve assembly (for exhaust camshaft) is set to 100%. |