Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2015.08
RM19Y0E _58 Vehicle Interior _003008 METER / GAUGE / DISPLAY _0015206 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Entire Combination Meter does not Operate  


DESCRIPTION

This circuit provides power to the combination meter assembly.

WIRING DIAGRAM

E305633E02
2.792,0.823 3.729,1.167 0.938,0.344 10 false BACK UP 4.729,2.177 5.281,2.5 0.552,0.323 10 false E34 4.719,2.333 6.802,2.771 2.083,0.438 10 false Combination Meter Assembly 4.979,1.656 5.427,2.042 0.448,0.385 10 false 7 5.208,1.771 5.656,2.156 0.448,0.385 10 false E 4.979,0.552 5.427,0.938 0.448,0.385 10 false 3 4.979,1.104 5.427,1.49 0.448,0.385 10 false 5 5.219,1.208 5.667,1.594 0.448,0.385 10 false IG 5.198,0.656 5.646,1.042 0.448,0.385 10 false +B 3.833,0.823 4.771,1.167 0.938,0.344 10 false BACK UP2 3.917,1.354 4.854,1.698 0.938,0.344 10 false ECU IG2 1.094,0.646 2.385,1.052 1.292,0.406 10 false from Battery 0.563,1.177 1.938,1.99 1.375,0.813 10 false from No. 1 Integration Relay Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY AND BODY GROUND)
E208723C07
1.469,0.177 1.958,0.469 0.49,0.292 1.365,1.875 1.198,1.875 1.198,1.875 1.031,1.208 true 0.448,1.875 0.615,1.875 0.615,1.875 0.781,1.208 true 1.948,1.781 1.781,1.781 1.781,1.781 1.281,1.198 true 0.115,0.073 0.573,0.479 0.458,0.406 10 false *a 1.594,0.24 2.094,0.521 0.5,0.281 10 false E34 2.031,1.708 2.458,2.177 0.427,0.469 10 false E 1.448,1.802 1.823,2.135 0.375,0.333 10 false IG 0.208,1.792 0.635,2.115 0.427,0.323 10 false +B
*a Front view of wire harness connector
(to Combination Meter Assembly connector)


a.

Disconnect the E34 combination meter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E34-3 (+B) - Body ground Always 11 to 14 V
E34-5 (IG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E34-7 (E) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR