Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › from 2015.08
RM19Y0E _54 Brake _002992 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0015137 ANTI-LOCK BRAKE SYSTEM D

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  FREEZE FRAME DATA  


FREEZE FRAME DATA


a.

Whenever a DTC is stored, the skid control ECU (brake actuator assembly) stores the current vehicle (sensor) state as freeze frame data.


b.

The skid control ECU (brake actuator assembly) stores the number of times (maximum: 31) the ignition switch has been turned from off to ON since the last time the ABS was activated.

HINT:
·

If the vehicle is stopped or at a low speed (7 km/h (4 mph) or less), or if a DTC is stored, the skid control ECU (brake actuator assembly) stops counting the number of times the ignition switch has been turned from off to ON.

·

Freeze frame data at the time the ABS operates:

The skid control ECU (brake actuator assembly) stores and updates data whenever the ABS operates.

When the ECU stores data at the time a DTC is stored, the data stored during ABS operation is cleared.

·

Freeze frame data at the time a DTC is stored:

When the skid control ECU (brake actuator assembly) stores data at the time a DTC is stored, no updates are performed until the data is cleared.





CHECK FREEZE FRAME DATA


a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.


e.

According to the display on the GTS or Techstream, select the trouble code data display with freeze frame data.

Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle speed Maximum wheel speed sensor reading Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Vehicle acceleration Vehicle acceleration Min.: -25.10 m/s2
Max.: 24.90 m/s2
Vehicle stopped: 0 km/h (0 mph) During deceleration/acceleration: Changes continuously
Wheel speed sensor FR Front speed sensor RH reading Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Wheel speed sensor FL Front speed sensor LH reading Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Wheel speed sensor RR Rear speed sensor RH reading Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Wheel speed sensor RL Rear speed sensor LH reading Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
+IG1voltage +IG voltage value Min.: 0.00 V
Max.: 20.00 V
Ignition switch on: 11 to 14 V Changes in proportion to battery voltage
Solenoid valve power voltage +BS voltage value Min.: 0.00 V
Max.: 20.00 V
Always: 11.00 to 14.00 V Changes in proportion to battery voltage
+B1 +BM voltage value Min.: 0.00 V
Max.: 20.00 V
Motor ON: 11.00 to 14.00 V
Motor OFF: 0.00 V
Changes in proportion to battery voltage
IG-ON elapsed time Time elapsed after ignition switch turned on Min.: 0 sec
Max.: 65535 sec
- -
Operation system Operated system status ABS, VSC(TRC), PBA, PB, Unknown, No Sys - ABS : ABS activated
VSC : VSC activated
PBA : PBA activated
PB : PB activated
Sys : System prohibited
Stop lamp SW Stop light switch assembly ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
IG ON frequency Number of operations of ignition switch being turned to ON after storing Freeze Frame Data 0 to 31 - -
Freeze elapsed Time Elapsed time after storing freeze frame data Min.: 0 ms
Max.: 500 ms
- -
Elapse time (STP ON - control ON) Elapsed time Min.: 0 ms
Max.: 12750 ms
- -
Control continuous time Elapsed time Min.: 0 ms
Max.: 12750 ms
- -
Number of diagnosis codes Number of DTCs stored Min. : 0
Max. : 255
- -



CLEAR FREEZE FRAME DATA


NOTICE:

Clearing the DTCs will also clear the freeze frame data.


a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream to ON.