DATA LIST
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS or Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Turn the ignition switch off.
Connect the GTS or Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the GTS or Techstream on.
Enter the following menus:
for ABS/VSC/TRC: Chassis / ABS/VSC/TRC / Data List.
for Body: Body Electrical / Body / Data List.
According to the display on the GTS or Techstream, read the Data List.
ABS/VSC/TRC
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Wheel speed FR | Front speed sensor RH reading | Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph) |
Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Wheel speed FL | Front speed sensor LH reading | Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph) |
Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Wheel speed RR | Rear speed sensor RH reading | Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph) |
Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Wheel speed RL | Rear speed sensor LH reading | Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph) |
Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| +IG 1 voltage | +IG voltage value | Min.: 0.00 V
Max.: 20.00 V |
Ignition switch on: 11 to 14 V | Changes in proportion to battery voltage |
| Solenoid valve power voltage | +BS voltage value | Min.: 0.00 V
Max.: 20.00 V |
Always: 11.00 to 14.00 V | Changes in proportion to battery voltage |
| +B1 | +BM voltage value | Min.: 0.00 V
Max.: 20.00 V |
Motor ON: 11.00 to 14.00 V
Motor OFF: 0.00 V |
Changes in proportion to battery voltage |
| Stop lamp SW | Stop light switch assembly | ON or OFF | ON: Brake pedal depressed
OFF: Brake pedal released |
- |
| Meter vehicle speed Vout | Maximum wheel speed sensor reading | Min. : 0
Max. : 326.4 |
Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| ABS warning lamp | ABS warning light | ON or OFF | ON: Warning light on
OFF: Warning light off |
- |
| Brake warning lamp | Brake warning light | ON or OFF | ON: Warning light on
OFF: Warning light off |
- |
| Solenoid relay | Solenoid relay | ON or OFF | ON: Solenoid relay on
OFF: Solenoid relay off |
- |
| Motor relay 1 | Motor relay | ON or OFF | ON: Motor relay on
OFF: Motor relay off |
- |
| Retention solenoid FR | Front wheel RH hold solenoid | ON or OFF | ON: Operates
OFF: Does not operate |
- |
| Press. reduction SOL FR | Front wheel RH release solenoid | ON or OFF | ON: Operates
OFF: Does not operate |
- |
| Retention solenoid FL | Front wheel LH hold solenoid | ON or OFF | ON: Operates
OFF: Does not operate |
- |
| Press. reduction SOL FL | Front wheel LH release solenoid | ON or OFF | ON: Operates
OFF: Does not operate |
- |
| Retention solenoid RR | Rear wheel RH hold solenoid | ON or OFF | ON: Operates
OFF: Does not operate |
- |
| Press. reduction SOL RR | Rear wheel RH release solenoid | ON or OFF | ON: Operates
OFF: Does not operate |
- |
| Acceleration FR | Front wheel RH acceleration | Min.: -200.84 m/s2
Max.: 199.27 m/s2 |
- | During deceleration/acceleration: Changes continuously |
| Acceleration FL | Front wheel LH acceleration | Min.: -200.84 m/s2
Max.: 199.27 m/s2 |
- | During deceleration/acceleration: Changes continuously |
| Acceleration RR | Rear wheel RH acceleration | Min.: -200.84 m/s2
Max.: 199.27 m/s2 |
- | During deceleration/acceleration: Changes continuously |
| Acceleration RL | Rear wheel LH acceleration | Min.: -200.84 m/s2
Max.: 199.27 m/s2 |
- | During deceleration/acceleration: Changes continuously |
| FR ABS is being controlled | Front wheel RH ABS operation | ON or OFF | ON: Operates
OFF: Does not operate |
- |
| FL ABS is being controlled | Front wheel LH ABS operation | ON or OFF | ON: Operates
OFF: Does not operate |
- |
| RR ABS is being controlled | Rear wheel RH ABS operation | ON or OFF | ON: Operates
OFF: Does not operate |
- |
| RL ABS is being controlled | Rear wheel LH ABS operation | ON or OFF | ON: Operates
OFF: Does not operate |
- |
| RR EBD is being controlled | Rear wheel RH EBD operation | ON or OFF | ON: Operates
OFF: Does not operate |
- |
| RL EBD is being controlled | Rear wheel LH EBD operation | ON or OFF | ON: Operates
OFF: Does not operate |
- |
| FR wheel speed sensor temp cutout | Front speed sensor RH open detection | Error or Normal | Error: Momentary interruption
Normal: Normal |
Refer to DTC C0200/21. |
| FL wheel speed sensor temp cutout | Front speed sensor LH open detection | Error or Normal | Error: Momentary interruption
Normal: Normal |
Refer to DTC C0205/22. |
| RR wheel speed sensor temp cutout | Rear speed sensor RH open detection | Error or Normal | Error: Momentary interruption
Normal: Normal |
Refer to DTC C0210/23. |
| RL wheel speed sensor temp cutout | Rear speed sensor LH open detection | Error or Normal | Error: Momentary interruption
Normal: Normal |
Refer to DTC C0215/24. |
| IG voltage low | IG voltage value decreased | Error or Normal | Error: Momentary interruption
Normal: Normal |
Refer to DTC C1241/15. |
| IG voltage high | IG voltage value increased | Error or Normal | Error: Momentary interruption
Normal: Normal |
Refer to DTC C1241/16. |
| FR wheel speed sensor power temp cutout | Front speed sensor RH voltage open detection | Error or Normal | Error: Momentary interruption
Normal: Normal |
Refer to DTC C0200/21. |
| FL wheel speed sensor power temp cutout | Front speed sensor LH voltage open detection | Error or Normal | Error: Momentary interruption
Normal: Normal |
Refer to DTC C0205/22. |
| RR wheel speed sensor power temp cutout | Rear speed sensor RH voltage open detection | Error or Normal | Error: Momentary interruption
Normal: Normal |
Refer to DTC C0210/23. |
| RL wheel speed sensor power temp cutout | Rear speed sensor LH voltage open detection | Error or Normal | Error: Momentary interruption
Normal: Normal |
Refer to DTC C0215/24. |
| Number of diagnosis codes | Number of DTCs stored | Min. : 0
Max. : 255 |
- | - |
Body
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Stop SW | Stop light switch signal | ON or OFF | ON: Stop light switch on
OFF: Stop light switch off |
- |
| Brake Fluid SW | Brake level warning switch | ON or OFF | ON: Brake fluid switch on
OFF: Brake fluid switch off |
- |
ACTIVE TEST
Using the GTS or Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Turn the ignition switch off.
Connect the GTS or Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the GTS or Techstream on.
Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.
According to the display on the GTS or Techstream, perform the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| ABS motor relay | ABS motor relay | Relay ON/OFF | Operating sound of motor can be heard.
Vehicle condition: Vehicle stopped |
| Brake warning lamp | Brake warning light | Warning light ON/OFF | Observe the combination meter assembly.
Vehicle condition: Vehicle stopped |
| ABS warning lamp | ABS warning light | Warning light ON/OFF | Observe the combination meter assembly.
Vehicle condition: Vehicle stopped |
| SRRR | Rear wheel RH release solenoid | Solenoid ON/OFF | Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped |
| SRRH | Rear wheel RH hold solenoid | Solenoid ON/OFF | Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped |
| SFLR | Front wheel LH release solenoid | Solenoid ON/OFF | Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped |
| SFLH | Front wheel LH hold solenoid | Solenoid ON/OFF | Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped |
| SFRR | Front wheel RH release solenoid | Solenoid ON/OFF | Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped |
| SFRH | Front wheel RH hold solenoid | Solenoid ON/OFF | Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped |
| 2nd system air bleed | 2nd system air bleed | Secondary solenoid ON/OFF | Pump motor drive (used when removing air inside ABS actuator) |
| ACT RL | Rear left pressure reduction and retention solenoid | Solenoid ON/OFF | Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped |
| ACT RR | Rear right pressure reduction and retention solenoid | Solenoid ON/OFF | Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped |
| ACT FL | Front left pressure reduction and retention solenoid | Solenoid ON/OFF | Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped |
| ACT FR | Front right pressure reduction and retention solenoid | Solenoid ON/OFF | Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped |