Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › from 2015.08
RM19Y0E _55 Steering _002997 POWER ASSIST SYSTEMS _0015160 POWER STEERING SYSTEM D

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  FREEZE FRAME DATA  


FREEZE FRAME DATA


NOTICE:
·

It is difficult to show the specified values (judgment values) clearly because freeze frame data values change significantly due to differences in measurement conditions, surroundings, or vehicle conditions. For this reason, there may be a problem even when the values are within specifications.

·

Turn the ignition switch to ON and park the vehicle on level ground. Check the freeze frame data by using the GTS or Techstream.



a.

Turn the ignition switch off.


b.

Connect the GTS or Techstream to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS or Techstream on.


e.

Check the freeze frame data by following the prompts on the GTS or Techstream display.

HINT:

Refer to the GTS or Techstream operator's manual for further details.


Chassis > EPS
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle speed Vehicle speed from meter Min.: 0 km/h (0 mph)
Max.: 255 km/h (158.5 mph)
0 km/h (0 mph)
No significant fluctuation
Vehicle stopped
Vehicle driven at constant speed
Engine revolution speed Engine speed Min.: 0 rpm Engine is running at a constant speed No significant fluctuation
Motor actual current Current to motor Min.: -55.91A
Max.: 55.91A
Value changes in proportion to steering effort Power steering is in operation
Motor instruction current Requested current to motor Min.: -55.91A
Max.: 55.91A
Value changes in proportion to steering effort Power steering is in operation
Thermistor temperature ECU substrate temperature Min.: -125°C (-257°F)
Max.: 125°C (257°F)
-125 to 125°C (-257 to 257°F) Ignition switch ON
PIG power supply Power source voltage to activate motor Min.: 0 V
Max.: 21.1531 V
11 to 14 V Power steering is in operation
IG power supply ECU power source voltage Min.: 0 V
Max.: 21.1531 V
11 to 14 V Ignition switch ON
Steering torque Steering wheel torque Min.: -19.60 Nm
Max.: 19.60 Nm
Value changes in proportion to steering effort The engine is running and the steering wheel is being turned.
Output of torque sensor 1 Torque sensor 1 output value Min.: 0 V
Max.: 5 V
2.2 to 2.8 V
2.2 to 4.0 V
1.0 to 2.8 V
Steering wheel not turned (without load)
Steering wheel turned to right with vehicle stopped
Steering wheel turned to left with vehicle stopped
Output of torque sensor 2 Torque sensor 2 output value Min.: 0 V
Max.: 5 V
2.2 to 2.8 V
2.2 to 4.0 V
1.0 to 2.8 V
Steering wheel not turned (without load)
Steering wheel turned to right with vehicle stopped
Steering wheel turned to left with vehicle stopped
Motor voltage (+) Motor terminal M1 voltage Min.: 0 V
Max.: 20.00 V
Below 1 V
11 to 14 V
Steering wheel turned to right
Steering wheel turned to left
Motor voltage (-) Motor terminal M2 voltage Min.: 0 V
Max.: 20.00 V
11 to 14 V
Below 1 V
Steering wheel turned to right
Steering wheel turned to left
IG switch status Ignition switch signal ON or OFF ON: Ignition switch ON
OFF: Ignition switch ACC or off
-
Torque sensor power supply Torque sensor power source voltage Min.: 0 V
Max.: 21.1531 V
5 to 13 V Power steering is in operation
No. of diagnosis codes Number of detected DTCs when freeze frame data stored Min.: 0
Max.: 255
- -