Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › from 2015.08
RM19Y0E _55 Steering _002997 POWER ASSIST SYSTEMS _0015160 POWER STEERING SYSTEM U

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the GTS or Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Turn the ignition switch off.


b.

Connect the GTS or Techstream to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS or Techstream on.


e.

Enter the following menus: Chassis / EPS / Data List.


f.

According to the display on GTS or Techstream, read the Data List.

Chassis > EPS > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle speed Vehicle speed from meter Min.: 0 km/h (0 mph)
Max.: 255 km/h (158.5 mph)
Vehicle stopped: 0 km/h (0 mph)
Vehicle driven at constant speed: No significant fluctuation
-
Engine revolution speed Engine speed Min.: 0 rpm Engine is running at a constant speed No significant fluctuation
Motor actual current Current to motor Min.: -55.91A
Max.: 55.91A
Value changes in proportion to steering effort Power steering is in operation
Motor instruction current Requested current to motor Min.: -55.91A
Max.: 55.91A
Value changes in proportion to steering effort Power steering is in operation
Thermistor temperature ECU substrate temperature Min.: -125°C (-257°F)
Max.: 125°C (257°F)
-125 to 125°C (-257 to 257°F) Ignition switch ON
PIG power supply Power source voltage to activate motor Min.: 0 V
Max.: 21.1531 V
11 to 14 V Power steering is in operation
IG power supply ECU power source voltage Min.: 0 V
Max.: 21.1531 V
11 to 14 V Ignition switch ON
Steering torque Steering wheel torque Min.: -19.60 Nm
Max.: 19.60 Nm
Value changes in proportion to steering effort The engine is running and the steering wheel is being turned.
Output of torque sensor 1 Torque sensor 1 output value Min.: 0 V
Max.: 5 V
Steering wheel not turned (without load): 2.2 to 2.8 V
Steering wheel not turned (without load): 2.2 to 4.0 V
Steering wheel turned to left with vehicle stopped: 1.0 to 2.8 V
-
Output of torque sensor 2 Torque sensor 2 output value Min.: 0 V
Max.: 5 V
Steering wheel not turned (without load): 2.2 to 2.8 V
Steering wheel turned to right with vehicle stopped: 2.2 to 4.0 V
Steering wheel turned to left with vehicle stopped: 1.0 to 2.8 V
-
Motor voltage (+) Motor terminal M1 voltage Min.: 0 V
Max.: 20.00 V
Steering wheel turned to right: Below 1 V
Steering wheel turned to left: 11 to 14 V
-
Motor voltage (-) Motor terminal M2 voltage Min.: 0 V
Max.: 20.00 V
Steering wheel turned to right: 11 to 14 V
Steering wheel turned to left: Below 1 V
-
IG switch status Ignition switch signal ON or OFF ON: Ignition switch ON
OFF: Ignition switch ACC or off
-
Torque sensor power supply Torque sensor power source voltage Min.: 0 V
Max.: 21.1531 V
5 to 13 V Power steering is in operation
No. of diagnosis codes Number of detected DTCs when freeze frame data stored Min.: 0
Max.: 255
- -
Diagnosis mode Diagnosis mode Normal/Check - -