ECM
Each ECM terminal's standard voltage or resistance is shown in the table below.
In the table, first follow the information under "Condition". Look under "Symbols (Terminals No.)" for the terminals to be inspected. The standard voltage or resistance between the terminals is shown under "Specified Condition".
Use the illustration above as a reference for the ECM terminals.
| Symbols (Terminals No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A24-1 (+B1) - C50-5 (E02) | G - W-B | Power source of ECM | Ignition switch ON | 11 to 14 V |
| A24-2 (+B2) - C50-5 (E02) | G - W-B | Power source of ECM | Ignition switch ON | 11 to 14 V |
| A24-13 (BAT) - C50-5 (E02) | G - W-B | Battery (for ECU memory) | Always | 11 to 14 V |
| A24-25 (HCAN) - C50-5 (E02) | GR - W-B | CAN communication line | Ignition switch ON | Pulse generation (See waveform 1) |
| A24-26 (LCAN) - C50-5 (E02) | W - W-B | CAN communication line | Ignition switch ON | Pulse generation (See waveform 2) |
| A24-60 (STSW) - A24-46 (STR-) | R - L | Starter signal | Cranking | 11 to 14 V |
| A24-65 (ODCS) - Body ground | SB - Body ground | D shift position indicator signal | Ignition switch ON with shift lever in D | Below 1 V |
| Ignition switch ON with shift lever not in D | 11 to 14 V | |||
| A24-66 (D) - C50-5 (E02) | Y - W-B | 3 shift position switch signal | Ignition switch ON with shift lever in 3 | Below 1 V |
| Ignition switch ON with shift lever not in 3 | 11 to 14 V | |||
| A24-68 (R) - C50-5 (E02) | V - W-B | R shift position switch signal | Ignition switch ON with shift lever in R | 11 to 14 V |
| Ignition switch ON with shift lever not in R | Below 1 V | |||
| C50-4 (E01) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| C50-5 (E02) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| C50-24 (B1+) - C50-25 (B1-) | BR - SB | SL1 solenoid signal | Engine idling speed | Pulse generation (See waveform 3) |
| C50-26 (C2+) - C50-27 (C2-) | LG - R | SL2 solenoid signal | Engine idling speed | Pulse generation (See waveform 4) |
| C50-28 (C3+) - C50-29 (C3-) | B - V | SL3 solenoid signal | Engine idling speed | Pulse generation (See waveform 5) |
| C50-46 (SLS) - C50-5 (E02) | Y - W-B | SL solenoid signal | When electricity is turned on | 11 to 14 V |
| When electricity is not turned on | Below 1 V | |||
| C50-47 (VBTB) - C50-5 (E02) | G-W - W-B | Power source of input speed sensor | Ignition switch ON | 11 to 14 V |
| C50-48 (VBOP) - C50-5 (E02) | L-W - W-B | Power source of output speed sensor | Ignition switch ON | 11 to 14 V |
| C50-49 (NSSB) - C50-5 (E02) | GR-B - W-B | L shift position switch signal | Ignition switch ON with shift lever in L | Below 1 V |
| Ignition switch ON with shift lever not in L | 11 to 14 V | |||
| C50-50 (NSSP) - C50-5 (E02) | P-G - W-B | P shift position switch signal | Ignition switch ON with shift lever in P | Below 1 V |
| Ignition switch ON with shift lever not in P | 11 to 14 V | |||
| C50-66 (SLT+) - C50-44 (SLT-) | W - L | SLT solenoid signal | Engine idling speed | Pulse generation (See waveform 6) |
| C50-67 (OTMP) - C50-89 (ETMP) | P - G | ATF temperature sensor signal | ATF temperature: 80°C (176°F) or more | Below 1.1 V |
| ATF temperature: 20°C (68°F) | Approximately 3.4 V | |||
| C50-69 (RTBN) - C50-91 (ETBN) | V-G - R-W | Input speed sensor signal | Vehicle speed 20 km/h (12 mph) | Pulse generation (See waveform 7) |
| C50-70 (ROTP) - C50-92 (EOPT) | BR-R - W-L | Output speed sensor signal | Vehicle speed 20 km/h (12 mph) | Pulse generation (See waveform 8) |
| C50-71 (SD) - C50-5 (E02) | B-Y - W-B | 2 shift position switch signal | Ignition switch ON with shift lever in 2 | Below 1 V |
| Ignition switch ON with shift lever not in 2 | 11 to 14 V | |||
| C50-88 (SLU+) - C50-45 (SLU-) | GR - BE | SLU solenoid signal | Engine idling speed | Pulse generation (See waveform 9) |
| C50-93 (NSSN) - C50-5 (E02) | LG-R - W-B | N shift position switch signal | Ignition switch ON with shift lever in N | Below 1 V |
| Ignition switch ON with shift lever not in N | 11 to 14 V | |||
| C50-105 (E1) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Waveform 1
| Terminal | HCAN - E02 |
| Tool setting | 1 V/DIV, 10 ms/DIV |
| Vehicle condition | Ignition switch ON |
Waveform 2
| Terminal | LCAN - E02 |
| Tool setting | 1 V/DIV, 10 ms/DIV |
| Vehicle condition | Ignition switch ON |
Waveform 3
| Terminal | B1+ - B1- |
| Tool setting | 5 V/DIV, 1 ms/DIV |
| Vehicle condition | Engine idling speed |
While shifting and adjusting the line pressure, the duty ratio becomes smaller.
Waveform 4
| Terminal | C2+ - C2- |
| Tool setting | 5 V/DIV, 1 ms/DIV |
| Vehicle condition | Engine idling speed |
During the shift, the duty ratio becomes smaller.
Waveform 5
| Terminal | C3+ - C3- |
| Tool setting | 5 V/DIV, 1 ms/DIV |
| Vehicle condition | Engine idling speed |
During the shift, the duty ratio becomes smaller.
waveform 6
| Terminal | SLT+ - SLT- |
| Tool setting | 5 V/DIV, 1 ms/DIV |
| Vehicle condition | Engine idling speed |
During the shift, the duty ratio becomes smaller.
Waveform 7
| Terminal | RTBN - ETBN |
| Tool setting | 5 V/DIV, 1 ms/DIV |
| Vehicle condition | Vehicle speed 20 km/h (12 mph) |
As the turbine speed becomes higher, the frequency becomes shorter.
Waveform 8
| Terminal | ROTP - EOPT |
| Tool setting | 5 V/DIV, 1 ms/DIV |
| Vehicle condition | Vehicle speed 20 km/h (12 mph) |
As the output speed (vehicle speed) becomes higher, the frequency becomes shorter.
Waveform 9
| Terminal | SLU+ - SLU- |
| Tool setting | 5 V/DIV, 1 ms/DIV |
| Vehicle condition | Engine idling speed |
During the shift, the duty ratio becomes smaller.