Home › Drivetrain › A4R AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM › from 2015.08
RM19Y0E _52 Drivetrain _041457 A4R AUTOMATIC TRANSMISSION / TRANSAXLE _0192556 AUTOMATIC TRANSMISSION SYSTEM D

A4R AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  DTC CHECK / CLEAR  


CHECK DTC (Using GTS or Techstream)


a.

DTCs which are stored in the ECM can be displayed with the GTS or Techstream or a generic OBD scan tool.

These scan tools can display pending DTCs and current DTCs. Some DTCs are not stored if the ECM does not detect a malfunction during consecutive driving cycles. However, the detected malfunction during one driving cycle is stored as a pending DTC.

i.

Connect the GTS or Techstream to the DLC3.


ii.

Turn the ignition switch to ON.


iii.

Turn the GTS or Techstream on.


iv.

Enter the following menus: Powertrain / A/T / Trouble Codes

Powertrain > A/T > Trouble Codes
50001 565

v.

Confirm the DTCs and freeze frame data and then write them down.


vi.

Confirm the details of the DTCs.

Click hereDrivetrain>A4R AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>DIAGNOSTIC TROUBLE CODE CHART

NOTICE:

For DTCs in the DIAGNOSTIC TROUBLE CODE CHART, which are subject to 2-trip detection logic, perform the following actions.


Turn the ignition switch off after the symptom is simulated once. Then repeat the simulation process again. When the problem has been simulated twice, the AT indicator light blinks (MIL illuminates) and the DTCs are recorded in the ECM.




CHECK DTC (Not using GTS or Techstream)


a.
F100115C01
1.594,0.333 1.594,0.781 true 1.823,1.458 1.823,1.813 true 1.563,0.125 1.885,0.417 0.323,0.292 10 false E 1.646,1.854 2.229,2.177 0.583,0.323 10 false ECUT 0.156,0.104 0.479,0.396 0.323,0.292 10 false *1
*1 DLC3


Turn the ignition switch to ON.


b.

Using SST, connect terminals 13 (ECUT) and 4 (E) of the DLC3.

SST
09843-18040  

NOTICE:
·

If the connecting position is wrong, trouble occurs.

·

When the check terminal is connected, the warning lamps, which are not for the electronic controlling automatic transmission system turn on, however, this is not a malfunction in the system.




c.
C143853E03
1.51,0.115 2.552,0.479 1.042,0.365 10 0.25 Seconds 1.354,1.781 2.458,2.094 1.104,0.313 10 0.25 Seconds 0.052,0.063 1.146,0.448 1.094,0.385 10 Normal Code

Read the DTC indicated by the number of times the AT indicator light blinks.

HINT:

If the system is operating normally, the light will blink 2 times per second.



d.
C143841E05
2.979,0.917 2.979,0.406 false 3.25,2.5 3.177,2.615 false 0.073,2.271 1.083,2.719 1.01,0.448 10 4.0 Seconds 1.198,2.271 2.094,2.74 0.896,0.469 10 1.5 Seconds 2.25,2.271 3.292,2.75 1.042,0.479 10 4.0 Seconds 2.729,2.615 3.375,3.021 0.646,0.406 10 Repeat 0.167,1.521 0.677,1.833 0.51,0.313 10 OFF 0.177,1.188 0.656,1.521 0.479,0.333 10 ON 0.552,0.76 1.604,1.208 1.052,0.448 10 0.5 Seconds 1.948,0.76 2.938,1.156 0.99,0.396 10 2.5 Seconds 0.073,0.083 1.688,0.51 1.615,0.427 10 Trouble Code "42" 2.354,0.167 3.417,0.573 1.063,0.406 10 For Next Code

The trouble code is indicated as shown on the left (DTC "42" is shown as an example).

HINT:

When 2 or more trouble codes are stored in the memory, the lower-numbered code is displayed first.




CLEAR DTC (Using GTS or Techstream)


a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Powertrain / A/T / Trouble Codes

Powertrain > A/T > Clear DTCs
50002 565


CLEAR DTC (Not using GTS or Techstream)


a.

Disconnect the battery cable or remove the EFI fuse from the Engine room relay block for 60 seconds or more.