Home › Drivetrain › A4R AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM › from 2015.08
RM19Y0E _52 Drivetrain _041457 A4R AUTOMATIC TRANSMISSION / TRANSAXLE _0192556 AUTOMATIC TRANSMISSION SYSTEM U

A4R AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  FAIL-SAFE CHART  


FAIL-SAFE


a.

Fail-safe function:

The fail-safe function operates to maintain vehicle drivability as much as possible even when a malfunction occurs in the input/output signal system in the ECM.

If the system returns to normal after a malfunction is detected, the fail-safe function is cancelled, but the diagnostic results remain stored.

The AT indicator light blinks during fail-safe operation.

DTC No. Detection Item Fail-safe control Release condition of fail-safe control
P0562 System Voltage Low When a malfunction is detected, hold in 3rd. After the system condition returns to normal, turn the ignition switch off.
P0642 Sensor Reference Voltage "A" Circuit Low
P0705 Transmission Range Sensor Circuit Malfunction Perform normal gear change controlling as the shift lever in D. The system condition returns to normal.
Transmission Range Sensor Circuit Malfunction
P0710 Transmission Fluid Temperature Sensor "A" Circuit When a malfunction is detected, shift into the 3rd and then shift into the 1st to 3rd depending on the vehicle speed and throttle opening angle. After the system condition returns to normal, shift into P or N when the vehicle speed is 0 km/h.
P0711 Transmission Fluid Temperature Sensor Circuit Range / Performance
P0717 Turbine Speed Sensor Malfunction
P0722 Output Speed Sensor Circuit
·

If the malfunction is in the sensor system, keep the gear position just before the malfunction is detected and if the vehicle stops, hold in 1st.

·

When a malfunction is detected, shift into the 3rd and then shift into the 1st to 3rd depending on the vehicle speed and throttle opening angle.


·

If the trouble is in the sensor system, after the system condition returns to normal, shift into P or N when the vehicle speed is 0 km/h.

·

If the trouble is in the automatic transmission assembly, after the system condition returns to normal, turn the ignition switch off.


P0730 Gear Ratio Malfunction Prohibit activation of line pressure control
If abnormal gear ratio is detected even when the line pressure control is prohibited, the following controls are performed.
·

If the abnormal gear ratio is detected with the shift lever in D, 3rd or 2nd, hold in 3rd.

·

If the abnormal gear ratio is detected with the shift lever in R or L, shift into the 1st to 3rd.


After the system condition returns to normal, turn the ignition switch off.
P0741 Lock up Speed is not Conformable Prohibit locking up. After the system condition returns to normal, shift into P or N when the vehicle speed is 0 km/h.
P0743 Shift Solenoid "E" Electrical
(Shift Solenoid Valve DSL)
·

Prohibit electricity from flowing into the malfunctioning solenoid.

·

When the type of trouble is a short circuit, shift into the 1st to 3rd using a normal solenoid. However, if a short circuit has occurred in the SL3 solenoid and SLT solenoid, hold in 3rd.

·

When the type of trouble is open circuit or the trouble exists in at least 2 solenoids, hold in 3rd.


After the system condition returns to normal, turn the ignition switch off.
P0748 Shift Solenoid "A" Electrical
(Shift Solenoid Valve SL1)
P0778 Shift Solenoid "B" Electrical
(Shift Solenoid Valve SL2)
P0798 Shift Solenoid "C" Electrical
(Shift Solenoid Valve SL3)
P2716 SLT solenoid system malfunction
(Line Pressure Control Solenoid Assembly)
P2759 Shift Solenoid "D" Electrical
(Lock Up Control Solenoid Assembly)