Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM › from 2015.08
RM19Y0E _58 Vehicle Interior _003005 DOOR LOCK _0015187 WIRELESS DOOR LOCK CONTROL SYSTEM D

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM  CUSTOMIZE PARAMETERS  


CUSTOMIZE WIRELESS DOOR LOCK CONTROL SYSTEM (w/o Theft Warning ECU Assembly)


HINT:

The following items can be customized.


NOTICE:
·

When the customer requests a change in a function, first make sure that the function can be customized.

·

Be sure to make a note of the current settings before customizing.

·

When troubleshooting a function, first make sure that the function is set to the default setting.



a.

Customizing with the GTS or Techstream

i.

Connect the GTS or Techstream to the DLC3.


ii.

Turn the ignition switch to ON.


iii.

Turn the GTS or Techstream on.


iv.

Enter the following menus: Customize Setting / Hazard.


v.

Select the setting by referring to the table below.

Tester Display Description Default Setting ECU
Answer back hazard operation When the doors are locked by wireless operation, the hazard warning lights flash once.
When the doors are unlocked by wireless operation, the hazard warning lights flash twice.
ON 00:OFF,01:ON Main body ECU (Fuse Block Assembly)




CUSTOMIZE WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Theft Warning ECU Assembly)



HINT:

The following item can be customized.


NOTICE:
·

When the customer requests a change in a function, first make sure that the function(s) can be customized.

·

Be sure to write down the current setting before customizing.



Item Default Contents Setting Relevant ECU
Wireless answer-back function Hazard warning lights flash and security warning buzzer sounds Function that makes hazard warning lights flash and security warning buzzer sound for answer-back when transmitter LOCK/UNLOCK switch pressed Only hazard warning lights flash/Hazard warning lights flash and security warning buzzer sounds/None Theft Warning ECU assembly

CUSTOMIZE METHOD FLOWCHART OF ANSWER-BACK FUNCTION


·

During customization mode, the alarm control functions are disabled.

·

During customization mode, the following wireless control functions are disabled: remote alarm function, automatic locking function, operation stop function and illuminated entry function.

·

In the flowchart, "lock operation" and "unlock operation" refer to wireless transmitter lock operation and unlock operation.

·

During customization mode, the ECU will not output lock/unlock signals.

·

At any time during customization mode, inserting the key into the key cylinder will end customization mode.



1.KEY IS NOT INSERTED INTO IGNITION KEY CYLINDER


Proceed to
NEXT


2.INSERT KEY AND PULL OUT KEY. REPEAT ONCE WITHIN 5 SECONDS.


a.

Insert the key into the ignition key cylinder, and then pull it out. Repeat this within 5 seconds (ending with key pulled out).

HINT:

If the key is inserted into the key cylinder and the ignition switch is turned ON, the customization mode will be canceled.


Proceed to
NEXT



3.PERFORM LOCK OPERATION


a.

Perform the lock operation once.

NOTICE:

Perform this procedure within 5 seconds of completing the previous step.


HINT:

If the lock operation is performed over 5 times, customization mode will end.


Proceed to
NEXT



4.PERFORM UNLOCK OPERATION


a.

Perform the unlock operation once.

NOTICE:

Perform this procedure within 2 seconds of performing the last lock operation of the previous step.


HINT:
·

After the hazard warning lights flash once, the user can confirm the customize setting, customize the setting, or end customization mode.

·

A selection must be made within 10 seconds.



Proceed to
NEXT



5.SELECT CUSTOMIZE MODE SETTING


Customize:
Item Proceed to
Check current setting Go to step 6
Wireless answer-back function: Only hazard warning lights flash Go to step 7
Wireless answer-back function: Hazard warning lights flash and security warning buzzer sounds Go to step 8
Wireless answer-back function: None Go to step 9
End customization mode Go to step 10



6.CHECK CURRENT SETTING


a.

Perform the unlock operation once.

Result:
Result Wireless Answer-back Function
Hazard warning lights flash once Only hazard warning lights flash
Hazard warning lights flash twice Hazard warning lights flash and security warning buzzer sounds
Hazard warning lights flash 3 times None


Proceed to
NEXT



END



7.TURN FUNCTION AND SETTING ON


a.

Perform the lock operation once. Then perform the unlock operation again within 2 seconds.

HINT:

The hazard warning lights will flash once.


Proceed to
NEXT



END



8.TURN FUNCTION AND SETTING ON


a.

Perform the lock operation twice. Then perform the unlock operation again within 2 seconds.

HINT:

The hazard warning lights will flash twice.


Proceed to
NEXT



END



9.TURN FUNCTION AND SETTING OFF


a.

Perform the lock operation 3 times. Then perform the unlock operation again within 2 seconds.

HINT:

The hazard warning lights will flash 3 times.


Proceed to
NEXT



END



10.END CUSTOMIZE MODE


a.

Perform the lock operation 4 times.

Proceed to
NEXT



END